Frequency: 433MHz;
Operating Range: Up to 300ft* (in open area);
Motion Sensor Range Detection Area: see picture;
Power Supply of Call Button: 23A 12V battery x 1
(included);
Power Supply of Motion Sensor: AA battery x 3
(included) or 6-12V AC adaptor (not included);
Power Supply of Pager: AA battery x 2 (included);
USER MANUAL
Please read this manual carefully before using the product.
For questions – email: .
Thank you for
your purchase.
support.synlett@gaxintech.com
Introduction
This simple caregiver pager system is an effective call and alert solution for staff
or caregiver when assistance is required.
Call Button may be mounted on the headboard of a bed or worn as a pendant
with lanyard. Press the call button to alert the pager remotely up to 300 feet*
range.
The Motion Sensor alerts the caregiver wearing the pager of a resident’s activities
when the resident interrupts the motion sensor’s infrared field, as long as they
are within 300 feet* of each other.
The Caregiver Pager has an option of an audible alarm/chime to choose from and
is compact enough to be carried in a pocket, clipped to a belt, or placed on a desk.
This system allows both caregiver and resident freedom while calling for help.
SIMPLE CAREGIVER PAGER SYSTEM
Caregiver Pager
M091B
Call Button
F100
Motion Sensor
QF029
Product Specifications
*Note: surrounding metal walls or other electronic devices
might interfere or affect the signal range.
Mount Call Button with Double Sided Tape (Optional)
Call Button - Setup
Battery Installation for Call Button
1 3
2
Insert the battery
(included) inside the
call button.
Gently pry open with
the flathead screwdriver
to access the battery
compartment.
Push the button on the call
button, the indicator lights
up which means the call
button is working correctly.
Front View
Side View
Inside View
12V 23A
+
_
Double
Sided
Tape
Top View
Place double sided tape on back of call button and mount to wall.
Call Button Installation
Lace Lanyard Strap thru Call Button (Optional)
Lace lanyard strap thru top
of call button.
Wrap loop around dark
blue cord and pull tight.
Double
Sided
Tape
Screw
Guides
A. Wall Mount with Double Sided Tape The
mounting brackets may be affixed to most smooth,
clean surfaces with the included double sided tape.
B. Wall Mount with Screws (included)
The mounting bracket may be more securely
mounted to walls or headboards with screws. Use
the recessed guides for screw placement on the
bracket.
Mount Call Button to Wall with Bracket (Optional)
1
Hang call
button from
the strap.
3
2
1 2 3
DC 8-12V
Motion Sensor - Setup
Motion Sensor - Setup
Push in to release the battery
compartment cover. Remove the
insulating pull tab from the battery
and close the battery compartment
cover.
Slide the main switch to :
waving a hand in front of the infrared
sensor. If the indicator lights up, it
means the motion sensor is working
correctly and a signal is being sent to
the pager.
SEND
2
Motion Sensor
- +
Bracket
Indicator
Light
Call Button
Infrared Sensor
Main
Switch:
Send/Off
/Push
Antenna
Detection
Distance
Knob
Battery
Compartment
Adaptor
Input
(adaptor
not
included)
Front View
Back View
Montion Sensor Installation
Double
Sided
Tape
Bracket
Recessced
Holes
Screws
A. Wall Mount with Double Sided Tape
The motion sensor may be affixed to most smooth,
clean surfaces with the included double sided tape.
B. Wall Mount with Screws
The motion sensor may be more securely mounted
to walls or headboards with the included screws. Use
the recessed holes for screw placement on the
motion sensor.
Mount the Motion Sensor
If you use screws to fix the motion sensor to a
permanent position, you will need to separate it from
the bracket before you screw the bracket to a fixture.
- Rotate the motion sensor in its bracket 90 degrees
so that it is facing the ceiling.
- Apply gentle pressure to one arm of the bracket so
the motion sensor can easily pop out.
1
To Next Page
General