DESCRIPTION
The ARM200 automated system for swing gates is an electro-
mechanical non-reversing actuator that transmits motion to the leaf
via a worm screw system.
The actuator is available in more versions in 12 Vdc and 230 Vac.
The non-reversing system ensures the leaf is mechanically locked
when the motor is not operating. A convenient and safe release
system with customised key makes it possible to manually move
the leaf in the event of a malfunction or of a power failure.
ATTENTION:
The correct operation and the declared specications
only apply if TAU accessories and safety devices
are used.
In the absence of a mechanical clutch, the use of
a control unit with an adjustable electronic clutch,
or the installation of a sensitive edge, is required in
order to ensure crush-proof safety.
The ARM200 automated system was designed and
built for controlling vehicle access. Avoid any other
use whatever.
ACTUATOR PARTS (g.1)
Pos. Description
1 Actuator
2 Release device
3 Rod
4 Wing connection bracket
5 Rear bracket
6 Terminal board cover
DIMENSIONS (g.2)
INSTALLATION (g.3)
Electrical set-up (standard system - ARM200)
Pos. Description Cables
1 Attuatore 4x1,5 mm²
2 Control unit
3x1,5 mm²
(power supply)
3 TX photocells 4x0,5 mm²
4 RX photocells 2x0,5 mm²
5 Key-operated selector switch 3x0,5 mm²
6 Flashing light and aerial 2x1 mm² + 1RG58
7 Mechanical stops -
Electrical set-up (standard system
- ARM200BENC)
Pos. Description Cables
1 Attuatore 2x2,5 mm² + 3x0,5 mm²
2 Control unit
3x1,5 mm²
(power supply)
3 TX photocells 4x0,5 mm²
4 RX photocells 2x0,5 mm²
5 Key-operated selector switch 3x0,5 mm²
6 Flashing light and aerial 2x1 mm² + 1RG58
7 Mechanical stops -
Notes:
• Use suitable tubes and/or hoses to lay electric cables
• Choose short routes for cables and keep power cables separate
from control cables.
Preliminary checks
Prior to installing the automation, make all structural modications
in order to ensure safety distances and protect and segregate
areas in which people may be exposed to the risk of crushing,
shearing, dragging or similar dangers.
• Make sure the existing structure is sufciently sturdy and
stable;
• the mechanical parts must conform to the provisions of
Standards EN 12604 and EN 12605;
• leaf length in compliance with the actuator specications;
• regular and uniform movement of the leaves, without any
friction and dragging during their entire travel;
• stiff hinges in good conditions;
• presence of both opening and closing mechanical limit stops;
• presence of an efcient earthing for electrical connection of the
actuator.
Perform any necessary metalwork job before installing the
automated system.
The condition of the gate structure directly affects the
reliability and safety of the automated system.
Installation dimensions (g.4)
Determine the tting position of the actuator with reference to
g.4.
Check with care if the distance between the open leaf and
any obstacles (walls, fences etc.) is higher than the actuator
dimensions.
A
R
M
2
2
5
X° A (mm) B (mm) C (mm)
90 80 ÷ 85 110 ÷ 200 20 mm
90 90 110 ÷ 195 20 mm
90 95 110 ÷ 190 20 mm
90 100 110 ÷ 185 20 mm
90 105 110 ÷ 180 20 mm
90 110 ÷ 115 110 ÷ 175 20 mm
90 120 110 ÷ 170 20 mm
90 125 110 ÷ 165 20 mm
90 130 110 ÷ 160 20 mm
90 135 110 ÷ 155 20 mm
90 140 110 ÷ 150 20 mm
90 145 ÷ 150 110 ÷ 145 20 mm
90 155 110 ÷ 140 20 mm
90 160 110 ÷ 135 20 mm
90 165 110 ÷ 130 20 mm
90 170 110 ÷ 125 20 mm
90 175 ÷ 180 110 ÷ 120 20 mm
100 100 ÷ 120 110 ÷ 150 20 mm
100 125 110 ÷ 145 20 mm
100 130 110 ÷ 140 20 mm
100 135 110 ÷ 135 20 mm
100 140 110 ÷ 130 20 mm
100 145 110 ÷ 125 20 mm
100 150 110 ÷ 120 20 mm
A
R
M
2
5
0
X° A (mm) B (mm) C (mm)
90 80 ÷ 175 115 ÷ 250 20 mm
90 180 ÷ 185 115 ÷ 245 20 mm
90 190 115 ÷ 240 20 mm
90 195 115 ÷ 235 20 mm
90 200 115 ÷ 230 20 mm
100 100 ÷ 150 115 ÷ 250 20 mm
100 155 115 ÷ 245 20 mm
100 160 115 ÷ 240 20 mm
100 165 115 ÷ 235 20 mm
100 170 115 ÷ 230 20 mm
100 175 115 ÷ 225 20 mm
100 180 115 ÷ 220 20 mm
100 185 115 ÷ 215 20 mm
100 190 115 ÷ 210 20 mm
100 195 115 ÷ 205 20 mm
100 200 115 ÷ 200 20 mm
ENGLISH
To Next Page
Loading...
Need help?
General
