Texecom Premier 816 - Page 82

Quick Reference Guide Premier 412/816/832 Installation Manual
82 INS159-13
Menu
Function
Page
 Use Delay Timer to Defer Non-Zone Restorals
 Inhibit Keyswitch Operation Upon EOL Tamper
 Away Arm Overrides Alarm Transmission Delay
 Defer Reporting of Zone Restorals
 Use Delay Timer to Defer Zone Restorals

System Options 3
37
 Away Arm Exit Error Doesn’t Sound Bell
 Zone Test - Silence on No Violation
 Alarm Status Light Indicates Fire
 Enable Entry/Exit Tones for Panel Speaker
 Enable Cross Partitioning
 Enable EN 50131-1 Requirements
 Reinstate Bypassed Zones on Disarm
 Invert Panel Bell/Siren Output

Hardware Options
38
 Panel Output 1 Supervised for Faults
 Panel Output 2 Supervised for Faults
 Siren/Bell Output Supervised for Faults
 Panel Box Tamper Switch Monitored
 Auxiliary Fuse Supervised for Faults
 Battery Supervised for Faults
 AC Mains Supply is Monitored
 Telephone Line Is Monitored

Auxiliary Input Options
38
 Not Used
 Auxiliary Tamper
 Remote Reset
 Telephone Line Monitor
 Panic Alarm
 Silent PA
 Latched Key switch
 Momentary Key switch
-
Miscellaneous Options 1
38
 Enable Bell Squawk on AWAY Arm/Disarm
 Enable Bell Squawk on STAY Arm/Disarm
 Disable AC Fail Acknowledgement
 Disable Open/Close Reporting on STAY Arm
 Cross/Double Knock Timer is in Minutes
 Disable Zone Bypass when Armed
 Activated Zones Cause Alarm during Exit
 Control Timer 4 Performs Battery Test
-
Miscellaneous Options 2
39
 Disable Service Fault Acknowledgement
 Enable User Reset for Alarms
 Disable Online Printing
 Enable Bell Module and UK Options
 Enable DD 243:2002 Options
 Enable Confirmation after Entry Time-Out
 Invert Auxiliary Input Operation
 Auto BST/GMT Time Change
-
Miscellaneous Options 3
39
 Enable User Tamper Reset
 Allow Engineer Access when Armed

EN50131
40
 Fob Low Battery Arming
 Indicate Zone Soak Test
 Soak Test Acknowledgement
 Entry Stray Notification
 Entry Timeout Notification
Menu
Function
Page
 Expander Lost
 User Code Entry
 AC & Battery Fail Latch
Programming Remote Keypads

Keypad Options 1
42
 Partition 1 Operation
 Partition 2 Operation
 Partition 3 Operation
 Partition 4 Operation
 Permanent Keypad Status Display
 Press Any Key for Display
 Display Zones vs. Partitions
 Wrong Code Attempts = Code Tamper

Keypad Options 2
42
 Code Tamper Causes a Tamper Alarm
 Keypad Activation of Fire Alarm
 Keypad Activation of Medical Alarm
 Keypad Activation of PA Alarm
 Keypad PA Alarm is Silent
 Quick Arm with Keypad ARM Key
 Quick Disarm with Keypad DISARM Key
 Quick Bypass with Keypad BYPASS Key

Keypad Options 3
42
 Fire Alarm Tones from Keypad
 Burglary Alarm Tones from Keypad
 Trouble Tones from Keypad
 Acceptance Tones from Keypad
 Error Tones from Keypad
 Chime Tones from Keypad
 Entry Tones from Keypad
 Exit Tones from Keypad

Keypad Options 4
43
 Enable Keypad Zones (RKP8/16 Plus & Premier LCD/LCD-P/LCDL/LCDL-P)
 Disable Keypad Lid Tamper
 Zone Shift by 4
 Zone Shift by 8
 Zone Shift by 16
Programming Remote Expanders

Expander Partitions
44
 Partition 1 Operation
 Partition 2 Operation
 Partition 3 Operation
 Partition 4 Operation

Expander Tones
44
 Fire Alarm Tones from Expander
 Burglary Alarm Tones from Expander
 Trouble Tones from Expander
 Acceptance Tones from Expander
 Error Tones from Expander
 Chime Tones from Expander
 Entry Tones from Expander
 Exit Tones from Expander

Expander Volume Level
44