Tikom L9000 - User Manual

Start with Tuya Smart APPAPP Connection
Getting Started
Product Overview
5
A
5
B
D
2.56 in / 65 mm -3.5 in / 90 mm
“No-Go Zone”
“No-Go Zone”
“No-Go Zone”
Front Bumper
Laser Distance Sensor (LDS)
Wi-Fi Status Light
ON :󵿎Wi-Fi Connected
Flash :󵿎Wi-Fi not connected
Off :󵿎Sleep Mode or Power off
Clean/Power Button
Power on or Power off Robot :󵿎
Press and hold this button 3s.
Start/ Stop Cleaning :󵿎Short press this button.
Home Button
Return to Charging Station :󵿎
Short press this button.
Reset Wi-Fi :󵿎
Press and hold and buttons for 3s
in the same time.
Robot Status Light
Solid󵾯Blue :󵿎Full󵿎Charged(On󵿎Charging󵿎station)/
Normal󵿎(Not󵿎on󵿎Charging󵿎station)
Flash󵾯Blue :󵿎Charging󵿎(On󵿎Charging󵿎station)
Solid󵾯Red :󵿎Low󵿎Battery
Flash󵾯Red :󵿎Abnormal
Off :󵿎Power Off or Sleep Mode
3
4
5
1
7
6
8
2
Wi-Fi Only
2.4GHz
Remo ve
Remove
1 2
3 4
5
Notes:
Notes:
Please search “Tikom Technology” in YouTube to find installation videos.
Notes:
1
2
21
21
Charging: Flash Blue
Full Charged: Solid Blue
Low Battery: Solid Red
L9K_V1.5
Customer Service: support.us@tikom.com
— Always keep the charging station plugged in to ensure the robot can
automatically return to recharge when the battery level is low.
— Clear objects within 1.6 ft / 0.5 m of the left and right sides, and within
4.9 ft / 1.5 m in front of the Charging Station.
— Recommend to use adhesive tapes to fix Charging Station on the ground.
Please ensure your robot is fully charged before its first use. Attach Robot to the
Charging Station by aligning its charging Contacts with the charging Contacts
on the Charging Station. Once the robot is successfully connected to the
charging station, the voice prompt, “Start charging”.
Step 1: Mapping Whole House Layout
A. Children's playroom: where have too
many toys on the ground, robot easily gets
stuck in this place.
B. Bathroom: Where there is too much water
on the ground, and robot would be damaged
by water.
C. Certain Room: There are high steps in
some places, and the robot can’t get out once
it goes in. Robot is trapped.
D. Some furniture: Where robot would easily
get stuck because its height exceeds the
bottom height of certain furniture.
Step 3 : Edit room layout on APP
No-Mop Zone(Max 7): Special for Carpet areas. When Robot installs Mopping cloth holder, Robot
can't enter this zone to mop.
Virtual Wall (Max 20): Robot can't go cross virtual Wall.
Enter “Map Edit” in APP to merge, split rooms and rename each room to make sure the whole map is
same as your house layout.
Step 4: Enter “Map Management” to save current map
When the current map is lost or corrupted for some reason, you can use a saved map from the list of
Map Management."
4. Open Tuya Smart App,
Tap “Add Device” or “+”
at the upper right corner.
5. Robot is discovered,
then tap "Add" button.
6. Select the same router's
2.4GHz Wi-Fi as mobile
phone and enter the
correct password.
Tap ”Next”.
3. Press and hold and
buttons on the robot at the
same time for 3 seconds,
Robot will say “Wi-Fi reset,
ready for Wi-Fi
connection”, and Wi-Fi
Status Light will Fast Flash.
1. Search for Tuya Smart on
the App Store/Google
Play, or scan the QR code
above to download and
install it on your mobile
device.
2. Register and log in on
the app.
7. Connecting to Wi-Fi.
Robot will say
“Connecting to Wi-Fi”.
8. Connection successful,
and Robot will say “Wi-Fi
Connection Successful”, and
Wi-Fi Status light will be
If fail to connect Wi-Fi in Quick
Mode as above, please try Wi-Fi
connecting in AP Mode,
details please check
"3.4.4.2 Connect Wi-Fi with AP
Mode" on user manual at page
20.
Notes:
1. Place the robot docked on the charging station.
2. Press on the robot or press on App to let the robot start mapping.
Step 2: Set Restricted Zone
No matter when robot is cleaning or mapping, you could stop robot and set “No-Go Zone”,
“No-Mop Zone” or “Virtual Wall” in Tuya smart APP “Restricted Zone Setting” as you want, then let the
robot continue cleaning.
No-Go Zone (Max 7): To prevent Robot enter this zone in any time. For some place where robot
couldn’t clean, or don’t want robot enter in, or somewhere robot is easily stuck or trapped. Examples
are as below.
1. Ensure that Bluetooth on your smartphone or
tablet is turned ON.
2. Ensure that the robot and your mobile device are
in close proximity to the router during the
connection process.
3. Ensure that your smartphone or tablet is connected to a 2.4GHz Wi-Fi
network.
4. If your router is a dual-band 2.4GHz/5GHz router, select the 2.4GHz
network.
5. If both bands use the same Wi-Fi name in your router, rename the 2.4GHz
network on the router's control page and connect your mobile phone to
this newly named 2.4GHz network.
L9000 Installation Video
Release Button of Dust Bin
Reset Button
Use a needle to press this
button to reset device
Dust Outlet Port to
Self-Empty Base
Dust Bin & Water Tank
Release Button of Mopping
Cloth Holder
Mopping Cloth Holder
Charging Contacts on Dust Bin
(For Self-Empty Base)
During the initial cleaning, ensure that each room's door is open to assist the robot in fully exploring
your house.
Since the robot can cross thresholds up to 0.7 in / 18 mm high, if any room's outer threshold is
less than 0.7 in / 18 mm, but the threshold measured from the inside of the room is higher than
0.7 in / 18 mm due to height differences, the robot may enter but not exit the room, potentially
becoming trapped. In such cases, set up a "No-Go Zone" or "Virtual Wall" for this room as instructed
on page 37 to prevent the robot from being trapped in this room.
Please remove any objects from the floor that may entangle the robot vacuum, such as pet waste,
socks, clothing, tissues, toys, slippery items, and power cords. You can utilize the provided Cable Ties
to organize your wires and power cords.
2
3
1
5
＜
0.7 in
＜
0.7 in
1
32
＞0.7 in / 18 mm
＜0.7 in / 18 mm
C
“No-Go Zone”

Tikom L9000 Specifications

General

Brand	Tikom
Model	L9000
Category	Vacuum Cleaner
Language	English