Toky DL8A Series - User Manual

DL8ASeries
①When you use the meter, please pay attention that input channel should correspond to range, otherwise, the meter will be malfunction.
②Input signal < 1.2 times of range.
③When measuring AC signal, aviliable for 0～200Hz. When frequency is higher than 100Hz, the measuring accuracy is ±1%FS.
△
Model
DL8A-RC10V600
DL8A-IRC10V600
DL8A-IRC18V600
DL8A-RC10A1000
DL8A-IRC10A1000
DL8A-IRC18A1000
DL8A-RC10A1
DL8A-IRC10A1
DL8A-IRC18A1
IN1：0～10V；IN2：0～100V；IN3：0～600V
IN1：0～10V；IN2：0～100V；IN3：0～600V
IN1：0～10V；IN2：0～100V；IN3：0～600V
IN1：AC 0～5A IN2:DC 0～75mV
IN1：AC 0～5A IN2:DC 0～75mV
IN1：AC 0～5A IN2:DC 0～75mV
IN1:0～100mA、0～10mA IN2:0～1000mA
IN1:0～100mA、0～10mA IN2:0～1000mA
IN1:0～100mA、
0～10mA IN2:0～1000mA
Alarm
2 alarm
2 alarm
2 alarm
2 alarm
2 alarm
2 alarm
2 alarm
2 alarm
2 alarm
NO
4-20mA
4-20mA
NO
4-20mA
4-20mA
NO
4-20mA
4-20mA
NO
NO
RS485
NO
NO
RS485
NO
NO
RS485
Analog output
CommunicationInput channel and Range Default channel and range
IN3:600V
IN1:5A
IN2:1000mA
DL8A Voltage/Ampere Meter User Manual
⊙Accuracy: 0.5%F.S.
⊙AC/DC universal (for AC signal it measures true value).
⊙Different input channel has different range, wide measuring range.
⊙Two Hi/Lo setting alarm output.
⊙With analog output 4-20mA.
⊙RS485 communication interface, Modbus RTU protocol.
I. Code Illustration
Range
Version code
A：AC/DC current V：AC/DC voltage
10：No RS485 18：With RS485
B：One alarm C：Two alarms
A：No alarm R：Relay alarm
DL8A series voltage/ampere meter
Blank: No analogue output I：4~20mA analogue output
DL8A
Features:
Safe Caution
※ Please comply with the below important points.
Warning
Notice
Warning
1.
1.
A safty protection equipment must be installed or please contact with us for the relative information if the product is used under the
circumstance such as nuclear control, medical treatment equipment, automobile, train, airplane, aviation and equipment etc.. Otherwise,
it may cause serious loss, fire or person injury.
2.
2.
A panel must be installed, otherwise it may cause creepage (leakage).
3.
3.
Do not touch wire connectors when the power is on, otherwise you may get an electric shock.
4.
4.
Do not dismantle or modify the product. If you have to do so, please contact with us first. Otherwise it may cause electric shock and fire.
5.
5.
Please check the connection number while you connect the power supply wire or input signal, otherwise it may cause fire.
1
.This product cannot be used outdoors. Otherwise the working life of the product will become shorter, or an electric shock accident may happen.
2.
2.
When you connect wire to the power input connectors or signal input connectors, the moment of the No.20 AWG (0.50 mm） screw
tweaked to the connector is 0.74n.m - 0.9n.m. Otherwise the connectors may be damaged or get fire.
3.
3.
Please comply with the rated specification. Otherwise it may cause electric shock or fire, and damage the product.
4
.Do not use water or oil base cleaner to clean the product. Otherwise it may cause electric shock or fire and damage the product.
5.
5.
This product should be avoid working under the circumstance that is flammable, explosive, moist, under sunshine, heat radiation and vibration.
Otherwise it may cause explosion.
6.
6.
In this unit it must not have dust or deposit, otherwise it may cause fire or mechanical malfunction.
7.
7.
Do not use gasoline, chemical solvent to clean the cover of the product because such solvent can damage it. Please use some soft cloth with water
or alcohol to clean the plastic cover.
Caution
For your safe, please read the below content carefully before you use the meter!
KKDL8AE01A-A/0-20170822Psge 01
An accident danger may happen in a special condition.
The instruction of the symbol in the manual is as below.
An operation that does not comply with the instruction may lead to product damage.
An accident may happen if the operation does not comply with the instruction.
Please read the manual carefully before you use the meter.
-
B

Toky DL8A Series Specifications