Toshiba 1600XP SERIES - 10.5 Battery Backup Time and Discharge Process; 10.6 Battery Low Voltage Tolerances

8
1600XP/XPi Series Installation and Operation Manual – 60616-012
5. Installation Precautions
NOTICE
1. Observe the following environmental restrictions:
• Install the unit in a well-ventilated location; allow at least 4 inches (10 cm) on all sides for air
ventilation and for maintenance.
• Install the unit where the ambient temperature is within the range specied in Appendix A -
“Specications”.
• DO NOT install the UPS in areas that are subject to high humidity.
• DO NOT install the UPS in areas that allow exposure to direct sunlight.
• DO NOT install the UPS in areas that allow exposure to high levels of airborne dust, metal
particles, or ammable gases.
• DO NOT install the UPS in areas near sources of electrical noise. Ensuring a proper earth ground
will reduce the effects of electrical noise and will reduce the potential for electrical shock.
• DO NOT install the UPS in areas that would allow uids or any foreign object to get inside the
UPS.
2. UPS is intended for permanent installation only. Install the unit in a stable, level and upright position
that is free of excessive vibration.
3. Follow the instructions on the unpacking label afxed to the exterior of the UPS.
4. Retain the shipping rails for use as permanent mounting of the UPS.
WARNING
This unit contains se ale d lead a cid bat terie s.
La ck of p re venta tive m ainte nan ce cou ld result
in b atte ries explod in g a nd e mittin g ga sses an d/o r
flam e. An nu al preven tative maintena nce must be
pe rformed by a n a utho rized, traine d te chnician.
WARNING
CR IT ICAL FUSE SIZ ING
Incor rect fu se replacem ent size
may result in fir e or inadeq uate
equ ipment protection.
Re pla ce only with same type
and rating of fuse.
49455 SHEET
CAUTIO N/
A TTEN TI O N
Do not di sco nne ct
whi le unit is
o pe rati ng
on battery power.
Nes pas debrancher
sous cha rg e.
48524 SHEET
Risk of electric sho ck. Do not remove cover.
. Refer servicing to qualified se rvice personnel.
N O USER SERVIC E AB LE PA RTS
INSIDE
To reduce the risk of fire or electric shock, install in a temperature and
humid ity controlled indoor area free of conductive contamina nts.
En c as utilisation en atm osphere controlee. Consulter la notice technique.
Note: Service pe rsonnel only.
Hazardous live parts inside the UPS are energized from the battery supp ly
even when the input AC power is d isconnected.
Capac itors store hazardous energy. Do not remove cover until 5 minutes
after disconnecting all sources of supp ly.
Battery b ackup time, which was factory-set at a predetermined level,
decreases gradually b etween service periods. The ba tterie s should be
replaced every three yea rs after the last servicing, the date of which is
written on the ID plate lo cated on the rea r side of the UPS unit, or in the
boxes b elow.
Date of last battery charge:
WARNING
CAUTION
Do not i n sert ba tte ry trays w i th the power o ff !
Th is uni t is desi gned for ho t chan geable batt eries!
When i nstalli ng batteries, the UPS must b e in the
onlin e or b ypass mode. Contact Toshiba
Intern ati onal Co rporation fo r further details.
6041 2
PN 51727
EXTERNAL BATTERY CABINET
The battery cabinet must have
a nominal battery voltage of
288VDC.
WARNING
DANGER/ATTENTION
Risk of electrical shock. Do not touch u ninsulated
batt ery terminals . Batteries should be serviced by
qua lified service repre se ntative only. Miswiring of
batt ery could result in ele ctrcal sh ock and/or fire.
Risque de choc electrique . Le circuit des ba tteries
nest pa s e so led e secteur. Les cosses des ba tteries
peu vent presenter une te nsion dange reuse part
rapport a la terre . Verifier avan t de to uch er.
DANGER
Batte ry fuse is always
l iv e . R i sk of ele ctr i ca l
shock. Check fuse
voltage an d discon nect
exter nal batte ries
befo re cha nging fuse.
48518 SHEET
fig 1
fig 2
1
2
3
Unpacking Instructions
P/N 48537
TYPEFORM
OUTPUT
MFD. IN U.S.A. FROM FOREIGN AN D DOMESTIC COMPONENTS HOUSTON, TEXAS
UNINTERRUPTIBLE POWER SUPPLY
INPUT
SERIAL NO.
PN 60381
LISTED
POWER
SUPPLY
27E5
C US
EPO
14
15
16
17
EPO 1
EPO 2
RE M O TE
REMOTE
1
L1
L2 G
X1 X2
208V
120V
120V
20 8/ 2 40 V
O UTPUT
I N PUT
N
X3
G
208V
USE COPPER 90 C ONDUC TORS ON LY. REFER TO IN STRUCTION MANUAL REGARDING TIGHTENING TO RQUE OF TERMINAL BLOCKS. FACTORY WIRED FO R 2 08V INPUT.
C OM
2
3
4
5
6 7
8
11
12
13
240V
240V
RE M O TE
JUMPE R SELECTION
50802