78
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
(E) 32/37/HL95 *Web 213 : 276
Locking video inputs
You can use the Input Lock feature to lock the video input
sources (VIDEO 1, VIDEO 2, ColorStream HD-1,
ColorStream HD-2, HDMI) and channels 3 and 4. You will not
be able to view the input sources or channels until you turn off
the input lock.
To lock the video inputs:
1. Press MENU and highlight the Locks menu icon.
2. Press z to display the PIN code entering screen.
3. Enter your four-digit PIN code and press ENTER.
4. Press z to highlight Input Lock and press ENTER.
5. Press • to select the level of video input locking you prefer,
as described below:
Video: Locks VIDEO 1,
VIDEO 2, ColorStream
HD1/HD2, and
HDMI.
Video+: Locks
VIDEO 1, VIDEO 2,
ColorStream HD1/
HD2, HDMI, and
channels 3 and 4. Select
Video+ if you use the antenna terminal to play a video tape.
Off: Unlocks all video input sources.
Blocking channels
With the Channels Block feature, you can block specific
channels. You will not be able to tune locked channels unless
you clear the setting first.
To block channels:
1. Press MENU and highlight the Locks menu icon.
2. Press z, which displays
the PIN code entering
screen.
3. Enter your four-digit
PIN code (see page 76
for details).
4. Press z to highlight
Channels Block and
then press ENTER.
5. Press yz to select the input that you want to change the
rating limits for (ANT1, ANT2 or Cable Box if connected)
and press ENTER. A list of the channels available for that
input will be displayed along with the call letters for each
channel, if available.
6. Press yzx • to
highlight the channel
you want to block, then
press ENTER, which
puts an “X” in the box
next to that channel.
7. Repeat step 5 for other
channels you want to
block.
8. Highlight Save and press ENTER or select another input in
this window, and the setting will automatically be selected.
To unlock individual channels:
In step 5 above, press yzx • to highlight the channel you
want to unblock, and then press ENTER to remove the “X”
from the box.
To block all channels at once:
Highlight Block All in step 5 above.
To unlock all locked channels at once:
Highlight Allow All in step 5 above.
Channel Block
ANT 1
1
ANT 1
ANT 2
Cancel
Save
Block All
Allow All
Cable Box
2
3
4
5
6
7
8
9
10
Chapter 9: Using the Locks menu
Unlocking programs temporarily
If you try to watch a TV program that exceeds the rating limits
you set, the TV enters program lock mode. You can either
unlock the program temporarily or select a non-locked program
to watch.
To temporarily unlock the program:
1. Press MUTE.
2. Enter your four-digit PIN code and press ENTER. If the
correct code is entered,
the program lock mode
is released and the
normal picture appears.
All locking is disabled
until the TV is turned
off, and will be enabled
when the TV is turned on again.
Navigate
Select
Back Exit
CH RTN
EXIT
Edit Rating Limits
Channels Block
Input Lock Off
Off
Off
Off
Front Panel Lock
Game Timer
New PIN Code
Locks
Enable Rating Blocking
Locks Active
Enter PIN code to temporaily un-
block.
Cancel
****
OK
Navigate
Select
Back Exit
CH RTN
EXIT
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock Off
Off
Off
Front Panel Lock
Game Timer
New PIN Code
Locks
Off
Off
Video
Video +
Channel Block
ANT 1
1
ANT 1
ANT 2
Cancel
Save
Block All
Allow All
Cable Box
2
3
4
5
6
7
8
9
10
#01E_076-079_3237HL95 5/20/05, 2:45 AM78
Black
To Next Page
Loading...
