Toshiba BC Series - Page 33

31 / 73
Copyright © 2019 Toshiba Teli Corporation, All Rights Reserved. http://www.toshiba-teli.co.jp/en/
D4296087A
* 0.4M : BC040M, 1.6M : BC160M
R/W ：Read / Write possible
R.O. ：Read Only
W.O. ：Write Only
N.A. ：Not available
Register
address
Read
Write
AC(*)
Memory
save
Default
Register name
0xC0
W.O.
-
-
Update scalable
0x1: Update registers related to scalable.
0xC4
R/W
✓
0x0
Offset Y
0.4M:0x0 (0)～0x1DC (476) OffsetY setting unit 2
0.4M:0x0 (0)～0x3F8 (1016) OffsetY setting unit 2
0xC8
R/W
✓
0.4M:0x21C
1.6M:0x438
Height
0.4M:0x40 (64)～0x21C (540) Height setting unit 2
1.6M:0x40 (64)～0x438 (1080) Height setting unit 2
0xCC
R/W
✓
0x0
Offset X
0.4M:0x0 (0)～0x290 (656) OffsetX setting unit 4
1.6M:0x0 (0)～0x560 (1376) OffsetX setting unit 4
0xD0
R/W
✓
0.4M:0x2D0
1.6M:0x5A0
Width
0.4M:0x40 (64)～0x2D0 (720) Width setting unit 4
1.6M:0x40 (64)～0x5A0 (1440) Width setting unit 4
0xD8
R/W
-
0x0
User area : address
Sets address of user area.
0x0～0xF(15)
0xDA
R/W
-
-
User area : data
Read /Write data to the specified by [User area : address].
The data length is specified by [User area : byte number].
0xDB
W.O.
-
-
User area : erase
0x1: erase all data in User area.
0xDC
R/W
-
0x10
User area : byte number
Sets the byte number of R/W length of user area.
0x1, 0x4, 0x8, 0x10(16)
0xF0
R/W
✓
0x0
SequentialShutter Enable
0x0:OFF,0x1:ON
0xF1
R/W
✓
0x1
SequentialShutter TerminateAt
Sets the number of Tables to repeat the sequence.
0x1 ～ 0x4
0xF3
R/W
✓
0x1
SequentialShutter Entry1
Sets the UserSet number to register to the first sequence.
0x1 ～ 0x4
0xF4
R/W
✓
0x1
SequentialShutter Entry2
Sets the UserSet number to register to the 2nd sequence.
0x1 ～ 0x4
0xF5
R/W
✓
0x1
SequentialShutter Entry3
Sets the UserSet number to register to the 3rd sequence.
0x1 ～ 0x4
0xF6
R/W
✓
0x1
SequentialShutter Entry4
Sets the UserSet number to register to the 4th sequence.
0x1 ～ 0x4
0xF7
W.O.
-
-
SequenceMemory Load
0x1: Load the parameters from the memory specified [Memory bank] register.
0xF8
W.O.
-
-
SequenceMemory Save
0x1: Save the parameters from the memory specified [Memory bank] register.
If camera teruned off, the data in memory for SS is erased.