CN301 PWA-F-LGC (CN301) <-> COIN CONTROLLER (OPTION)/
COPY KEY CARD (OPTION)
CN302 PWA-F-LGC (CN302) <-> KEY COPY COUNTER (OPTION)
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM,
MAIN-SW (RESET), TEMP/HUMI-SNR, FRNT-COV-SW
(e-STUDIO202L)
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM,
MAIN-SW (RESET), TEMP/HUMI-SNR, FRNT-COV-SW
(e-STUDIO232)
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM,
MAIN-SW (RESET), TEMP/HUMI-SNR, FRNT-COV-SW
(e-STUDIO282)
CN304 PWA-F-LGC (CN304) <-> PWA-F-ADU (CN211, 212), ADU-CLT,
SID-COV-SNR, SFB-SIZE-SNR, SFB-SNR, SFB-FEED-CLT,
SFB-SOL, SFB-FEED-SNR-2
CN305 PWA-F-LGC (CN305) <-> FEED-SNR-1, RGST-SNR,
TR-COV-SW, TNR-SW, AUG-LOCK-SW, TNR-MOT, MAIN-MOT,
REAR-FAN-MOT, MID-FAN-MOT, RGST, CLT.TR-U-CLT, TR-M-CLT
CN306 PWA-F-LGC (CN306) <-> EXIT-MOT, EXIT-FAN-MOT, JOB
SEPARATOR (OPTION)/OFFSET TRAY (OPTION)/
BRIDGE UNIT (OPTION)
CN307 PWA-F-LGC (CN307) <-> EMP-U-SNR, CST-U-TRY-SNR,
CST-U-FEED-CLT, NEMP-U-SNR, TRY-MOT, TR-L-CLT,
EMP-L-SNR, CST-L-TRY-SNR, CST-L-FEED-CLT, NEMP-L-SNR,
CST-U-SW, CST-L-SW
CN308 PWA-F-LGC (CN308) <-> PS-HVT (CN720)/THMS-C-HTR,
THMS-S-HTR, THMS-EDG-HTR, EXT-SNR
CN310 PWA-F-LGC (CN310) <-> PFP (OPTION)/LCF (OPTION)
CN312 PWA-F-LGC (CN312) <-> M/DC-POL
CN313 PWA-F-LGC (CN313) <-> PWA-F-LRL (CN204)
CN316 PWA-F-LGC (CN316) <-> DOWNLOAD JIG (LGC)
CN317 PWA-F-LGC (CN317) <-> IPC BOARD (OPTION)
CN101 PWA-F-SYS (CN101) <-> PWA-F-SLG (CN4)
CN102 PWA-F-SYS (CN102) <-> FAX BOARD (CN701) (OPTION)
CN104 PWA-F-SYS (CN104) <-> PWA-F-DSP (J427)
CN107 PWA-F-SYS (CN107) <-> COIN CONTROLLER (OPTION)/
COPY KEY CARD (OPTION)
CN108 PWA-F-SYS (CN108) <-> DOWNLOAD JIG (SYS)
CN105 PWA-F-SYS (CN105) <-> DDR DIMM
CN109 PWA-F-SYS (CN109) <-> PWA-F-LGC (CN309)
CN110 PWA-F-SYS (CN110) <-> LAN (10BASE-T/100BASE-TX)
CN111 PWA-F-SYS (CN111) <-> INTERNAL USB CONNECTOR
CN112 PWA-F-SYS (CN112) <-> HDD (CN170) (STANDARD)
CN113 PWA-F-SYS (CN113) <-> BLUETOOTH MODULE
CN114 PWA-F-SYS (CN114) <-> USB CONNECTOR (HOST)
CN115 PWA-F-SYS (CN115) <-> USB CONNECTOR (DEVICE)
CN117 PWA-F-SYS (CN117) <-> HDD-FAN-MOT
CN118 PWA-F-SYS (CN118) <-> WIRELESS LAN MODULE (OPTION)
CN119 PWA-F-SYS (CN119) <-> HDD (CN17 1)
CN121 PWA-F-SYS (CN124) <-> PCI (CN801)/SCRAMBLER BOARD
(OPTION)
CN1 PWA-F-SLG (CN1) <-> PWA-F-CCD (CN14)
CN2 PWA-F-SLG (CN2) <-> PLTN-SNR, HOME-SNR
CN7 PWA-F-SLG (CN7) <-> RADF (CN2) (OPTION)
CN9 PWA-F-SLG (CN9) <-> INV-EXP (CN1)
CN10 PWA-F-SLG (CN10) <-> SLG-FAN-MOT,
APS1 (A4 SERIES ONLY), APS2, APS3, APS4, AP S5
CN19 PWA-F-SLG (CN19) <-> SCAN-MOT
CN22 PWA-F-SLG (CN22) <-> DOWNLOAD JIG (SLG)
CN2 INV-EXP (CN2) <-> LP-EXPO
CN206 PWA-F-LRL (CN206) <-> PER-F-LDR (C201)
CN207 PWA-F-LRL (CN207) <-> PWA-F-SNS (CN202)
CN705 PS-ACC (CN705) <-> PWA-F-SYS (CN120)
CN706 PS-ACC (CN706) <-> PWA-F-LGC (CN311), PWA-F-FUS (CN431)
CN707 PS-ACC (CN707) <-> FINISHER (J 599) (OPTION)/
PWA-F-ADU (CN212) (OPTION)/MAIN MOTOR
CN708 PS-ACC (CN708) <-> PWA-F-SLG (CN6)/RADF (CN1) (OPTION)
CN721 PS-HVT (OUT1) <-> MAIN CHARGER WIRE
CN722 PS-HVT (OUT2) <-> MAIN CHARGER GRID
CN723 PS-HVT (OUT3) <-> DEVELOPER BIAS
CN724 PS-HVT (OUT4) <-> TRANSFER BIAS
CN725 PS-HVT (OUT5) <-> SEPARATION BIAS
CN726 PS-HVT (OUT6) <-> TRANSFER GUIDE BIAS/REGISTRATION
ROLLER BIAS
J422 PWA-F-DSP (J422) <-> LCD PANEL
J423 PWA-F-DSP (J423) <-> LCD BACK LIGHT
J424 PWA-F-DSP (J424) <-> LCD PANEL
J425 PWA-F-DSP (J425) <-> PWA-F-KEY (J428)
J426 PWA-F-DSP (J426) <-> PWA-F-KEY (J429)
CN213 PWA-F-ADU (CN213) <-> ADU-TRL-SNR
CN214 PWA-F-ADU (CN214) <-> ADU-TRU-SNR
CN215 PWA-F-ADU (CN215) <-> ADU-MOT
CN217 PWA-F-ADU (CN217) <-> ADU-SET-SW
CN501 FAX (CN501) <-> NCU (1) (OPTION)
CN502 FAX (CN502) <-> NCU (2) (OPTION)
CN503 FAX (CN503) <-> SPEAKER (OPTION)
CN600 FAX (CN600) <-> MODEM BOARD (CN401) (OPTION)
CN602 FAX (CN602) <-> DOWNLOAD JIG (FAX) (OPTION)
J600 IPC BOARD (J600) <-> FINISHER (J598) (OPTION)
Pin No Symbol Name Active
A1 +24VD2 +24 V -
A2 CTRON Total counter ON signal -
A3 CTRCNT Copy key card connection detection signal L
A4 M/C RUN M/C run signal L
A5 EXTCTR Exit sensor ON signal L
A6 PG Power ground -
A7 BKCTR
Black and white mode counter ON signal and
CST-CTR signal
-
A8 MNCTR Mono-color mode counter ON signal -
B1 FLCTR
Full color mode counter ON signal and reverse
side counter signal
-
B2 SG Signal ground -
B3 TSIZE3 Paper size signal-3 -
B4 TSIZE2 Paper size signal-2 -
B5 TSIZE1 Paper size signal-1 -
B6 TSIZE0 Paper size signal-0 -
B7 +5.1VB +5.1 V -
B8 CTRCNT2 Copy key card /Coin counter judgment signal -
Pin No Symbol Name Active
1 NC Not connected -
2 SG Signal ground
3 KCTRC-0
Key copy counter/Copy key card connection
detection signal
L
4 +24VD2 +24 V -
5 KCTRO-0 Key copy counter ON signal -
6 NC Not connected -
Pin No Symbol Name Active
A1 ATSCNT-1 PU connection detection signal L
A2 ERSLP-0A Exposure lamp drive signal -
A3 +24VD1 +24 V -
A4 PG Power ground -
A5 ATS-1A Auto-toner sensor detection signal Analog
A6 +24VD1 +24 V (Auto-toner sensor) -
A7 ATSVR-1A Auto-toner sensor detection signal Analog
A8 DRTH-1 Drum thermistor detection signal Analog
A9 SG Signal ground -
A10 SG Signal ground -
B1 RSTSW-0A Reset signal to the main switch H
B2 +24VD1 +24 V -
B3 +5.1VB +5.1 V -
B4 HMS-1A Humidity sensor signal Analog
B5 SG Signal ground -
B6 TEMP-1 Temperature sensor signal Analog
B7 FCOVSW-1 Front cover opening/closing switch signal -
B8 SG Signal ground -
B9 NC Not connected -
B10 NC Not connected -
Pin No Symbol Name Active
A1 ATSCNT-1 PU connection detection signal L
A2 ERSLP-0A Exposure lamp drive signal -
A3 +24VD1 +24 V -
A4 PG Power ground -
A5 ATS-1A Auto-toner sensor detection signal Analog
A6 +24VD1 +24 V (Auto-toner sensor) -
A7 ATSVR-1A Auto-toner sensor detection signal Analog
A8 DRTH-1 Drum thermistor detection signal Analog
A9 SG Signal ground -
A10 SG Signal ground -
A11 NC Not connected -
B1 NC Not connected -
B2 RSTSW-0A Reset signal to the main switch H
B3 +24VD1 +24 V -
B4 +5.1VB +5.1 V -
B5 HMS-1A Humidity sensor signal Analog
B6 SG Signal ground -
B7 TEMP-1 Temperature sensor signal Analog
B8 FCOVSW-1 Front cover opening/closing switch signal -
B9 SG Signal ground -
B10 NC Not connected -
B11 NC Not connected -
Pin No Symbol Name Active
A1 ATSCNT-1 PU connection detection signal L
A2 ERSLP-0A Exposure lamp drive signal -
A3 +24VD1 +24 V -
A4 PG Power ground -
A5 ATS-1A Auto-toner sensor detection signal Analog
A6 +24VD1 +24 V (Auto-toner sensor) -
A7 ATSVR-1A Auto-toner sensor detection signal Analog
A8 DRTH-1 Drum thermistor detection signal Analog
A9 SG Signal ground -
A10 SG Signal ground -
A11 NC Not connected -
A12 NC Not connected -
B1 CPSW2-0 Not used -
B2 SG Signal ground -
B3 RSTSW-0A Reset signal to the main switch H
B4 +24VD1 +24 V -
B5 +5.1VB +5.1 V -
B6 HMS-1A Humidity sensor signal Analog
B7 SG Signal ground -
B8 TEMP-1 Temperature sensor signal Analog
B9 FCOVSW-1 Front cover opening/closing switch signal L
B10 SG Signal ground -
B11 NC Not connected -
B12 NC Not connected -
Pin No Symbol Name Active
A1 ADM1D-0A ADU motor drive signal-D -
A2 ADM1B-0A ADU motor drive signal-B -
A3 ADM1C-0A ADU motor drive signal-C -
A4 ADM1A-0A ADU motor drive signal-A -
A5 ADUVR-1 A DU motor current control reference voltage -
A6 ADTR2-1 ADU exit sensor detection signal -
A7 5.1VB +5.1 V -
A8 SG Signal ground -
A9 ADCNT-1 ADU connection detection signal L
A10 ADTR1-1 ADU entrance sensor detection signal L
A11 ADCOV-1 ADU opening/closing switch detection signal -
A12 +24VD2 +24 V -
A13 ADUCL-0A ADU clutch drive signal L
A14 SG Signal ground L
A15 CSTCSW-1
Side cover opening/closing sensor detection signal
L
A16 +5.1VB +5.1 V -
A17 NC Not connected -
A18 NC Not connected -
A19 NC Not connected -
A20 NC Not connected -
B1 SFSZ3-0 Not used -
B2 SG Signal ground -
B3 SG Signal ground -
B4 SFSZ0-0 Bypass paper size detection signal-1 -
B5 SFSZ1-0 Bypass paper size detection signal-2 -
B6 SFSZ2-0 Bypass paper size detection signal-3 -
B7 SG Signal ground -
B8 SFBEMP-1 Bypass paper detection signal -
B9 5.1VB +5.1 V -
B10 +24VD2 +24 V -
B11 SFBCL1-0 Bypass feed clutch drive signal L
B12 +24VD2 +24 V -
B13 SFBCL2-0 Bypass pickup solenoid drive signal -
B14 SG Signal ground -
B15 SFBTRY-1 Not used -
B16 +5.1VB +5.1 V -
B17 SG Signal ground -
B18 2NDFED-1 2nd transport sensor detection signal -
B19 +5.1VB +5.1 V -
B20 SFBCNT-1 Bypass unit connection detection signal -
Pin No Symbol Name Active
A1 SG Signal ground
A2 1STFEED-1 1st transport sensor detection signal
A3 +5.1VB +5.1 V
A4 SG Signal ground
A5 PSTPSW-1 Registration sensor detection signal -
A6 +5.1VB +5.1 V -
A7 SG Signal ground -
A8 SDCSW-1 Transfer cover opening/closing detection signal -
A9 NC Not connected -
A10 TNRSW-1 Toner cartridge installation detection signal -
A11 SG Signal ground -
A12 TNRFULL-1 Cleaner auger lock detection signal -
A13 SG Signal ground -
A14 TNRMT-0A Toner motor drive signal -
A15 TNRMT-1A Toner motor drive signal -
A16 NC Not connected -
A17 NC Not connected -
B1 RGTCL-0A Registration roller clutch drive signal -
B2 +24VD1 +24 V -
B3 1STCLL-0A Middle transport clutch drive signal -
B4 +24VD1 +24 V -
B5 1STCLH-0A Upper transport clutch drive signal -
B6 +24VD1 +24 V -
B7 MAMBK-0A Main motor brake signal
L: Braking
H: Normal
B8 MAMPL-1 Main motor PLL signal L: Normal
B9 MAMCW-0A Main motor rotational direction signal
L: CW,
H: CCW
B10 MAMCK-1 Main motor reference clock signal -
B11 MAMON-0A Main motor ON/OFF signal
L: ON,
H: OFF
B12 SG Signal ground -
B13 +5.1VB +5.1 V -
B14 +24VD1 +24 V -
B15 PWRFN-0A Internal cooling fan2 motor drive signal -
B16 +24VD1 +24 V -
B17 CLNFN-0A Internal cooling fan1 motor drive signal
Pin No Symbol Name Active
A1 +24VD2 +24 V
A2 EXTMA-0A Exit motor drive signal-A
A3 EXTMB-0A Exit motor drive signal-B
A4 EXTMC-0A Exit motor drive signal-C
A5 EXTMD-0A Exit motor drive signal-D
A6 +24VD2 +24 V -
A7 +24VD2 +24 V -
A8 VCMFN-0 Exhaust fan motor drive signal -
A9 NC Not connected -
A10 NC Not connected -
A11 NC Not connected -
A12 NC Not connected -
A13 NC Not connected -
A14 NC Not connected -
A15 NC Not connected -
A16 NC Not connected -
A17 NC Not connected -
A18 NC Not connected -
B1 RLC2S-1 JS P/OCT unit exit sensor signal -
B2 +5.1VB +5.1 V -
B3 RLHSW-1
JSP: lower stack sensor detection signal /
OCT: stack sensor detection signal
-
B4 SG Signal ground -
B5 JSPSW-0 JSP/OCT judgment signal L
B6 RLCNT-0 JSP/OCT judgment signal -
B7 OPCHK1-1 JSP/OCT judgment signal
L: OCT,
H: JSP
B8 RLCSW-1 JSP/OCT cover opening/closing detection signal L
B9 RLTRS-1
JSP: paper jam sensor detection signal /
OCT: paper feed sensor detection signal
-
B10 JFSL2OH-1
JSP: upper stack sensor detection signal /
OCT: separate sensor detection signal
-
B11 GASOL-0A JSP/OCT gate solenoid driving signal -
B12 +24VD2 +24 V -
B13 PG Power ground -
B14 OFFSET1 OCT motor drive signal-1 -
B15 OFFSET2 OCT motor drive signal-2 -
B16 NC Not connected -
B17 NC Not connected -
B18 NC Not connected -
Pin No Symbol Name Active
A1 SG Signal ground -
A2 CUEMP-1 Upper drawer empty sensor detection signal -
A3 +5.1VB +5.1 V -
A4 SG Signal ground -
A5 CUTOP-1 Upper drawer tray-up sensor detection signal -
A6 +5.1VB +5.1 V -
A7 CURGC-0A Upper drawer feed clutch drive signal -
A8 +24VD1 +24 V -
A9 SG Signal ground -
A10 CUFLS-1 Upper drawer paper stock sensor detection signal -
A11 +5.1VB +5.1 V -
A12 CLTRM-0A Tray-up motor drive signal -
A13 CLTRM-1A Tray-up motor drive signal -
A14 2NDCL-0A Lower transport clutch drive signal -
A15 +24VD1 +24 V -
B1 SG Signal ground -
B2 CLEMP-1 Lower drawer empty sensor detection signal -
B3 +5.1VB +5.1 V -
B4 SG Signal ground -
B5 CLTOP-1 Lower drawer tray-up sensor detection signal -
B6 +5.1VB +5.1 V -
B7 CLRGC-0 Lower drawer feed clutch drive signal -
B8 +24VD1 +24 V -
B9 SG Signal ground -
B10 CLFLS-1 Upper drawer paper stock sensor detection signal -
B11 +5.1VB +5.1 V
B12 SG Signal ground -
B13 CUSW-0 Upper drawer detection signal -
B14 SG Signal ground -
B15 CLSW-0 Lower drawer detection signal -
Pin No Symbol Name Active
A1 HVCLK-0A Developer AC bias high-voltage clock signal -
A2 HVSDWN-1A
High-voltage power supply leakage detection signal
L
A3 HVSAV-1A Separation bias voltage output reference voltage Analog
A4 HVTSP-0A Separation bias voltage ON/OFF signal -
A5 HVTGB-0A Transfer guide bias voltage ON/OFF signal -
A6 HVTVR-1A
Transfer bias high-voltage output reference voltage
Analog
A7 HVTT-0A Transfer bias high-voltage ON/OFF signal -
A8 HVAVR-1A
Developer AC bias high-voltage output reference voltage
Analog
A9 HVTAC-0A Developer AC bias high-voltage ON/OFF signal -
A10 HVDVR-1A
Developer DC bias high-voltage output reference voltage
Analog
A11 HVMVR-1A Main charger grid output reference voltage Analog
A12 HVTM-0A
Main needle electrode charger voltage ON/OFF signal
-
A13 SG Signal ground -
A14 +24VD2 +24 V
B1 FUSSW-1A Fuser roller thermistor connection detection signal -
B2 MTH+-1A Fuser roller center thermistor + signal Analog
B3 MTH--1A Fuser roller center thermistor - signal Analog
B4 STH+-1A Fuser roller side thermistor + signal Analog
B5 STH--1A Fuser roller side thermistor - signal Analog
B6 ETH+-1A Fuser roller edge thermistor + signal Analog
B7 ETH--1A Fuser roller edge thermistor - signal Analog
B8 +5.1VSW + 5.1 V -
B9 SG Signal ground -
B10 EXTSW-1 Exit sensor detection signal -
B11 +5.1VB +5.1 V -
B12 NC Not connected -
B13 NC Not connected -
B14 NC Not connected -
Pin No Symbol Name Act ive
A1 CLKC-1A PFP/LCF driver control latch signal (C) -
A2 CLKB-1A PFP/LCF driver control latch signal (B) -
A3 SCSWC-0A PFP/LCF sensor detection port enable signal (C) -
A4 DRV7-1A PFP/LCF driver control signal -
A5 DRV6-1A PFP/LCF driver control signal -
A6 DRV5-1A PFP/LCF driver control signal -
A7 DRV4-1A PFP/LCF driver control signal -
A8 DRV3-1A PFP/LCF driver control signal -
A9 DRV2-1A PFP/LCF driver control signal -
A10 DRV1-1A PFP/LCF driver control signal -
A11 DRV0-1A PFP/LCF driver control signal -
A12 PFRST-0 Reset signal -
A13 +5.1VB +5.1 V -
A14 SG Signal ground -
A15 +24VD1 +24 V -
A16 +24VD1 +24 V -
B1 PG Power ground -
B2 PG Power ground -
B3 SIZE0-0A Size data bus-0 -
B4 SIZE1-0A Size data bus-1 -
B5 SIZE2-0A Size data bus-2 -
B6 SIZE3-0A Size data bus-3 -
B7 RETS0-0A PFP/LCF sensor detection signal -
B8 RETS1-0A PFP/LCF sensor detection signal -
B9 RETS2-0A PFP/LCF sensor detection signal -
B10 RETS3-0A PFP/LCF sensor detection signal -
B11 RETS4-0A PFP/LCF sensor detection signal -
B12 RETS5-0A PFP/LCF sensor detection signal -
B13 RETS6-0A PFP/LCF sensor detection signal -
B14 RETS7-0A PFP/LCF sensor detection signal -
B15 SCSWB-0A PFP/LCF sensor detection port enable signal (B) -
B16 LCCNT-0 LCF connection detection signal L
Pin No Symbol Name Act ive
1 POMCK-0 Polygonal motor reference clock signal -
2 POMOL-0 Polygonal motor PLL signal L: Normal
3 POMON-0 Polygonal motor ON/OFF signal
L: ON
H: OFF
4 PG Power ground -
5 +24VD1 +24 V -
Pin No Symbol Name Act ive
1 SG Signal ground -
2 +5VD +5.1 V -
3 +5VD +5.1 V -
4 SG Signal ground -
5 WRLVL-1 Laser power control signal (reference voltage) -
6 SG Signal ground -
7 BDIN-1 Laser beam position detection signal (H-sync) -
8 SG Signal ground -
9 PIDT-1 Laser image data (differential signal +) -
10 PIDT-0 Laser image data (differential signal -) -
11 SG Signal ground -
12 WRAPC-0 APC write signal -
13 +5.1VB +5.1 V -
14 SHDWM-1 Laser shut down signal -
15 SG Signal ground -
16 +5.1VD +5.1 V
17 +5.1VD +5.1 V -
18 SG Signal ground -
Pin No Symbol Name Act ive
1 D[0] ROM data bus [0] -
2 D[2] ROM data bus [2] -
3 D[4] ROM data bus [4] -
4 D[6] ROM data bus [6] -
5 RD-0 ROM data read signal -
6 A[0] ROM address bus [0] -
7 A[2] ROM address bus [2] -
8 A[4] ROM address bus [4] -
9 A[6] ROM address bus [6] -
10 A[8] ROM address bus [8] -
11 A[10] ROM address bus [10] -
12 A[12] ROM address bus [12] -
13 A[14] ROM address bus [14] -
14 A[16] ROM address bus [16] -
15 A[18] ROM address bus [18] -
16 SG Signal ground -
17 SG Signal ground -
18 D[1] ROM data bus [1] -
19 D[3] ROM data bus [3] -
20 D[5] ROM data bus [5] -
21 D[7] ROM data bus [7] -
22 CS2-0 Chip select signal L
23 A[1] ROM address bus [1] -
24 A[3] ROM address bus [3] -
25 A[5] ROM address bus [5] -
26 A[7] ROM address bus [7] -
27 A[9] ROM address bus [9] -
28 A[11] ROM address bus [11] -
29 A[13] ROM address bus [13] -
30 A[15] ROM address bus [15] -
31 A[17] ROM address bus [17] -
32 ROMDT-0 Download board connection detection signal L
33 +5.1VB +5.1 V -
34 LED-0A External ROM loading status signal L
Pin No Symbol Name Act ive
1 SG Signal ground -
2 +5.1VB +5.1 V -
3 AD0 System address bus [0] -
4 AD2 System address bus [2] -
5 AD4 System address bus [4] -
6 AD6 System address bus [6] -
7 I/O0 System data bus [0] -
8 I/O2 System data bus [2] -
9 I/O4 System data bus [4] -
10 I/O6 System data bus [6] -
11 SG Signal ground -
12 WE Write signal -
13 CSIP2-0A IPC chip select signal -
14 +5.1VB +5.1 V -
15 IPCSW-0 IPC board connection detection signal L
16 SG Signal ground -
17 +5.1VB +5.1 V -
18 AD1 System address bus [1] -
19 AD3 System address bus [3] -
20 AD5 System address bus [5] -
21 AD7 System address bus [7] -
22 I/O1 System data bus [1] -
23 I/O3 System data bus [3] -
24 I/O5 System data bus [5] -
25 I/O7 System data bus [7] -
26 SG Signal ground -
27 OE O utput enable signal -
28 IPRST-0A IPC reset signal -
29 +5.1VB +5.1 V -
30 SG Signal ground -
Pin No Symbol Name Act ive
1 SYSRST System reset signal -
2 SCTS Transmission enabled -
3 STXD Transmitted SLG data -
4 SRXD Received SLG data -
5 SRTS Transmission request signal -
6 SCNT SLG board connection detection signal -
7 SG Signal ground -
8 SVDEN Vertical scanning synchronized signal -
9 SDCLK Clock signal for scanning data transmission -
10 SHDEN Horizontal scanning synchronized signal -
11 SG Signal ground -
12 SG Signal ground -
13 SCD7 Scanning data [7] -
14 SCD6 Scanning data [6] -
15 SCD5 Scanning data [5] -
16 SCD4 Scanning data [4] -
17 SCD3 Scanning data [3] -
18 SCD2 Scanning data [2] -
19 SCD1 Scanning data [1] -
20 SCD0 Scanning data [0] -
Pin No Symbol Name Act ive
1 +5.1VB +5.1 V -
2 DA1 IDE Address [1] -
3 +5.1VB +5.1 V -
4 DD0 FAX data bus [0] -
5 +5.1VB +5.1 V -
6 DD3 FAX data bus [3] -
7 +5.1VB +5.1 V -
8 DD6 FAX data bus [6] -
9 +5.1VB +5.1 V -
10 DD9 FAX data bus [9] -
11 SG Signal ground -
12 DD12 FAX data bus [12] -
13 SG Signal ground -
14 SG Signal ground -
15 SG Signal ground -
16 SG Signal ground -
17 SG Signal ground -
18 SG Signal ground -
19 +3.3VB +3.3 V -
20 INTRQ IDE Interrupt request signal -
21 +3.3VB +3.3 V -
22 +5.1VA +5.1 V -
23 -12VB -12 V -
24 SG Signal ground -
25 +12VB +12 V -
26 DA0 IDE Address [0] -
27 DA2 IDE Address [2] -
28 IDECS IDE chip select signal -
29 DD1 FAX data bus [1] -
30 DD2 FAX data bus [2] -
31 DD4 FAX data bus [4] -
32 DD5 FAX data bus [5] -
33 DD7 FAX data bus [7] -
34 DD8 FAX data bus [8] -
35 DD10 FAX data bus [10] -
36 DD11 FAX data bus [11] -
37 DD13 FAX data bus [13] -
38 DD14 FAX data bus [14] -
39 DD15 FAX data bus [15] -
40 /DIOR IDE I/O read signal -
41 /DIOW IDE I/O write signal -
42 /DMACK DMA acknowledge signal -
43 /DLDCS0 Chip select signal -
44 /RESET Reset signal L
45 DMARQ DMA request signal -
46 NC Not connected -
47 FXWP FAX wake-up signal -
48 SG Signal ground -
49 SG Signal ground -
50 NC Not connected -
Pin No Symbol Name Act ive
1 XSCL-1A LCD data transmission clock -
2 LP-1A LCD data latch pulse H
3 WF-1A LCD frame signal H
4 YD-1A LCD scanning line start signal H
5 INVGND Signal ground -
6 BZON-0A Buzzer-ON signal L
7 CPPOW-1A Panel connection detection signal H
8 LDCLK-1A LED serial clock -
9 LDDAT-1A LED serial data -
10 LDLTH-1A LED data latch signal L
11 LDON1-0A LED drive selection signal-1 L
12 LDON0-0A LED drive selection signal-0 L
13 SG Signal ground -
14 +5.1VA +5.1 V -
15 +5.1VA +5.1 V -
16 +5.1VA +5.1 V -
17 +5.1VA +5.1 V -
18 CPRST-0A Reset signal L
19 SG Signal ground -
20 RTS0-0A Key controller SIO Transmission request signal -
21 CTS0-0A Key controller SIO Transmission enabled signal -
22 SOUT(0) Key controller SIO transmitted serial data -
23 SIN(0) Key controller SIO received serial data -
24 SG Signal ground -
25 UD3-1A LCD display data-3 -
26 UD2-1A LCD display data-2 -
27 UD1-1A LCD display data-1 -
28 UD0-1A LCD display data-0 -
29 SG Signal ground -
30 LCDEN-1A LCD enable signal H
Pin No Symbol Name Act ive
1 L/S Paper size signal -
2 FULL-C Full-color mode signal -
3 MONO-C Mono-color mode signal -
4 B/W Black and white mode signal -
5 +5.1VA +5.1 V -
6 SG Signal ground -
7 NC Not connected -
Pin No Symbol Name Act ive
1 DATA0 System data bus [0] -
2 DATA2 System data bus [2] -
3 DATA4 System data bus [4] -
4 DATA6 System data bus [6] -
5 DATA8 System data bus [8] -
6 DATA10 System data bus [10] -
7 DATA12 System data bus [12] -
8 DATA14 System data bus [14] -
9 A21 System address bus [19] -
10 A19 System address bus [17] -
11 A17 System address bus [15] -
12 A15 System address bus [13] -
13 A13 System address bus [11] -
14 A11 System address bus [9] -
15 A09 System address bus [7] -
16 A07 System address bus [5] -
17 A05 System address bus [3] -
18 A03 System address bus [1] -
19 RDX System read signal -
20 CS0-A Chip select signal (0-A) -
21 CS0-B Chip select signal (0-B) -
22 +3.3VA +3.3 V -
23 +3.3VA +3.3 V -
24 SG Signal ground -
25 SG Signal ground -
26 DATA1 System data bus [1] -
27 DATA3 System data bus [3] -
28 DATA5 System data bus [5] -
29 DATA7 System data bus [7] -
30 DATA9 System data bus [9] -
31 DATA11 System data bus [11] -
32 DATA13 System data bus [13] -
33 DATA15 System data bus [15] -
34 A20 System address bus [18] -
35 A18 System address bus [16] -
36 A16 System address bus [14] -
37 A14 System address bus [12] -
38 A12 System address bus [10] -
39 A10 System address bus [8] -
40 A08 System address bus [6] -
41 A06 System address bus [4] -
42 A04 System address bus [2] -
43 A02 System address bus [0] -
44 A22 System address bus [21] -
45 /CS0 Chip select signal -
46 +3.3VA +3.3 V -
47 RMSL System control signal -
48 /WRX System write signal -
49 SG Signal ground -
50 SG Signal ground -
Pin No Symbol Name Active
1 VREF Reference voltage -
2 DQ0 Memory data bus [0] -
3 SG Signal ground -
4 DQ1 Memory data bus [1] -
5 DQS0 Data strobe signal [0] -
6 DQ2 Memory data bus [2] -
7 VDD +2.5 V -
8 DQ3 Memory data bus [3] -
9 NC Not connected -
10 NC Not connected -
11 SG Signal ground -
12 DQ8 Memory data bus [8] -
13 DQ9 Memory data bus [9] -
14 DQS1 Data strobe signal [1] -
15 VDD +2.5 V -
16 CK1 Clock-1 input -
17 /CK1 Differential clock-1 input -
18 SG Signal ground -
19 DQ10 Memory data bus [10] -
20 DQ11 Memory data bus [11] -
21 CKE0 Clock enable signal -
22 VDD +2.5 V -
23 DQ16 Memory data bus [16] -
24 DQ17 Memory data bus [17] -
25 DQS2 Data strobe signal [2] -
26 SG Signal ground -
27 A9 Memory address bus [9] -
28 DQ18 Memory data bus [18] -
29 A7 Memory address bus [7] -
30 VDD +2.5 V -
31 DQ19 Memory data bus [19] -
32 A5 Memory address bus [5] -
33 DQ24 Memory data bus [24] -
34 SG Signal ground -
35 DQ25 Memory data bus [25] -
36 DQS3 Data strobe signal [3] -
37 A4 Memory address bus [2] -
38 VDD +2.5 V -
39 DQ26 Memory data bus [26] -
40 DQ27 Memory data bus [27] -
41 A2 Memory address bus [1] -
42 SG Signal ground -
43 A1 Memory address bus [1] -
44 CB0 Not used -
45 CB1 Not used -
46 VDD +2.5 V -
47 DQS8 Data strobe signal [8] -
48 A0 Memory address bus [0] -
49 CB2 Not used -
50 SG Signal ground -
51 CB3 Not used -
52 BA1 Bank select-1 -
53 DQ32 Memory data bus [32] -
54 VDD +2.5 V -
55 DQ33 Memory data bus [33] -
56 DQS4 Data strobe signal [4] -
57 DQ34 Memory data bus [34] -
58 SG Signal ground -
59 BA0 Bank select-0 -
60 DQ35 Memory data bus [35] -
61 DQ40 Memory data bus [40] -
62 VDD +2.5 V -
63 /WE Data write enable signal -
64 DQ41 Memory data bus [41] -
65 /CAS Column address strobe signal -
66 SG Signal ground -
67 DQS5 Data strobe signal [5] -
68 DQ42 Memory data bus [42] -
69 DQ43 Memory data bus [43] -
70 VDD +2.5 V -
71 NC Not connected -
72 DQ48 Memory data bus [48] -
73 DQ49 Memory data bus [49] -
74 SG Signal ground -
75 /CK2 Differential clock-2 input -
76 CK2 Clock-2 input -
77 VDD +2.5 V -
78 DQS6 Data strobe signal [6] -
79 DQ50 Memory data bus [50] -
80 DQ51 Memory data bus [51] -
81 SG Signal ground -
82 VDD-ID Not used -
83 DQ56 Memory data bus [56] -
84 DQ57 Memory data bus [57] -
85 VDD +2.5 V -
86 DQS7 Data strobe signal [7] -
87 DQ58 Memory data bus [58] -
88 DQ59 Memory data bus [59] -
89 SG Signal ground -
90 WP Not connected -
91 SDA Presence-detect serial data -
92 SCL Presence-detect serial clock -
93 SG Signal ground -
94 DQ4 Memory data bus [4] -
95 DQ5 Memory data bus [5] -
96 VDD +2.5 V -
97 DM0 Data write mask signal [0] -
98 DQ6 Memory data bus [6] -
99 DQ7 Memory data bus [7] -
100 SG Signal ground -
101 NC Not connected -
102 NC Not connected -
103 NC Not connected -
104 VDD +2.5 V -
105 DQ12 Memory data bus [12] -
106 DQ13 Memory data bus [13] -
107 DM1 Data write mask signal [1] -
108 VDD +2.5 V -
109 DQ14 Memory data bus [14] -
110 DQ15 Memory data bus [15] -
111 CKE1 Clock enable signal -
112 VDD +2.5 V -
113 NC Not connected -
114 DQ20 Memory data bus [20] -
115 A12 Memory address bus [12] -
116 SG Signal ground -
117 DQ21 Memory data bus [21] -
118 A11 Memory address bus [11] -
119 DM2 Data write mask signal [2] -
120 VDD +2.5 V -
121 DQ22 Memory data bus [22] -
122 A8 Memory address bus [4] -
123 DQ23 Memory data bus [23] -
124 SG Signal ground -
125 A6 Memory address bus [3] -
126 DQ28 Memory data bus [28] -
127 DQ29 Memory data bus [29] -
128 VDD +2.5 V -
129 DM3 Data write mask signal [3] -
130 A3 Memory address bus [3] -
131 DQ30 Memory data bus [30] -
132 SG Signal ground -
133 DQ31 Memory data bus [31] -
134 CB4 Not used -
135 CB5 Not used -
136 VDD +2.5 V -
137 CK0 Clock-0 input -
138 /CK0 Differential clock-0 input -
139 SG Signal ground -
140 DM8 Data write mask signal [8] -
141 A10 Memory address bus [10] -
142 CB6 Not used -
143 VDD +2.5 V -
144 CB7 Not used -
145 SG Signal ground -
146 DQ36 Memory data bus [36] -
147 DQ37 Memory data bus [37] -
148 VDD +2.5 V -
149 DM4 Data write mask signal [4] -
150 DQ38 Memory data bus [38] -
151 DQ39 Memory data bus [39] -
152 SG Signal ground -
153 DQ44 Memory data bus [44] -
154 /RAS Row address strobe signal -
155 DQ45 Memory data bus [45] -
156 VDD +2.5 V -
157 /CS0 Chip select signal-0 -
158 /CS1 Chip select signal-1 -
159 DM5 Data write mask signal [5] -
160 SG Signal ground -
161 DQ46 Memory data bus [46] -
162 DQ47 Memory data bus [47] -
163 NC Not connected -
164 VDD +2.5 V -
165 DQ52 Memory data bus [52] -
166 DQ53 Memory data bus [53] -
167 NC Not connected -
168 VDD +2.5 V -
169 DM6 Data write mask signal [6] -
170 DQ54 Memory data bus [54] -
171 DQ55 Memory data bus [55] -
172 VDD +2.5 V -
173 NC Not connected -
174 DQ60 Memory data bus [60] -
175 DQ61 Memory data bus [61] -
176 SG Signal ground -
177 DM7 Data write mask signal [7] -
178 DQ62 Memory data bus [62] -
179 DQ63 Memory data bus [63] -
180 VDD +2.5 V -
181 SA0 Presence-detect address [0] -
182 SA1 Presence-detect address [1] -
183 SA2 Presence-detect address [2] -
184 +3.3VA +3.3 V -
Pin No Symbol Name Active
A1 +5.1VB +5.1 V -
A2 CBSY-0 System command busy -
A3 CMD-0 Command data -
A4 SACK-0 System status acknowledge signal -
A5 SERR-0 System status error signal -
A6 SBSY-0 System status busy signal -
A7 STS-0 Status data -
A8 CACK-0 System command acknowledge signal -
A9 CERR-0 System command error signal -
A10 SG Signal ground -
A11 SG Signal ground -
A12 SG Signal ground -
A13 IRCLK-1 Clock signal input for image data transmission -
A14 SG Signal ground -
A15 HSYNC-0 Horizontal scanning synchronized signal -
A16 SG Signal ground -
A17 VSYNC-0 Vertical scanning synchronized signal -
B1 MCNT-1 LGC board connection detection signal -
B2 SYSRST-0 System reset signal -
B3 IDATX[0] IDA Transmitted data bus [0] -
B4 IDATX[1] IDA Transmitted data bus [1] -
B5 IDATX[2] IDA Transmitted data bus [2] -
B6 IDATX[3] IDA Transmitted data bus [3] -
B7 IDATX[4] IDA Transmitted data bus [4] -
B8 IDATX[5] IDA Transmitted data bus [5] -
B9 IDATX[6] IDA Transmitted data bus [6] -
B10 IDATX[7] IDA Transmitted data bus [7] -
B11 SG Signal ground -
B12 IDCLK-1 Clock signal output for image data transmission -
B13 SG Signal ground -
B14 IHDEN-0 Data enable of the horizontal scanning direction -
B15 SG Signal ground -
B16 IVDEN-0 Data enable of the vertical scanning direction -
B17 +3.3VB +3.3 V -
Pin No Symbol Name Active
1 TXD+ Transmitted data + -
2 TXD- Transmitted data - -
3 RXIN+ Received data + -
4 GND Not used -
5 GND Not used -
6 RXIN- Received data - -
7 GND Not used -
8 GND Not used -
Pin No Symbol Name Active
1 VBUS +5.1 V -
2 D0- USB serial data -
3 D0+ USB serial data -
4 SG Signal ground -
5 VBUS +5.1 V -
6 D1- USB serial data -
7 D1+ USB serial data -
8 SG Signal ground -
Pin No Symbol Name Active
1 /RESET Reset signal -
2 SG Signal ground -
3 DD7 Data bus [7] -
4 DD8 Data bus [8] -
5 DD6 Data bus [6] -
6 DD9 Data bus [9] -
7 DD5 Data bus [5] -
8 DD10 Data bus [10] -
9 DD4 Data bus [4] -
10 DD11 Data bus [11] -
11 DD3 Data bus [3] -
12 DD12 Data bus [12] -
13 DD2 Data bus [2] -
14 DD13 Data bus [13] -
15 DD1 Data bus [1] -
16 DD14 Data bus [14] -
17 DD0 Data bus [0] -
18 DD15 Data bus [15] -
19 SG Signal ground -
20 NC(KEY) Not connected -
21 MDARQ DMA request signal H
22 SG Signal ground -
23 /DIOW I/O write signal -
24 SG Signal ground -
25 /DIOR I/O read signal -
26 SG Signal ground -
27 IORDY I/O ready signal -
28 SG Signal ground -
29 /DMACK DMA acknowledge signal L
30 SG Signal ground -
31 INTRQ Interrupt request signal H
32 RESERVED Reserve signal -
33 DA1 Device address [1] -
34 /PDIAG Passed diagnostics L
35 DA0 Device address [0] -
36 DA2 Device address [2] -
37 /CS0 Chip select-0 L
38 /CS1 Chip select-1 L
39 /DASP Device active or slave present signal L
40 SG Signal ground -
Pin No Symbol Name Active
1 VDD +5.1 V -
2 NC Not connected -
3 NC Not connected -
4 D- Serial data -
5 D+ Serial data -
6 NC Not connected -
7 NC Not connected -
8 DETACH Signal ground -
9 NC Not connected -
10 SG Signal ground -
11 NC Not connected -
12 NC Not connected -
13 /RESET Reset signal -
14 NC Not connected -
15 NC Not connected -
16 NC Not connected -
17 NC Not connected -
18 NC Not connected -
19 NC Not connected -
20 SG Signal ground -
Pin No Symbol Name Active
1 VBUS +5.1 V -
2 D0- USB serial data -
3 D0+ USB serial data -
4 SG Signal ground -
5 VBUS +5.1 V -
6 D1- USB serial data -
7 D1+ USB serial data -
8 SG Signal ground -
Pin No Symbol Name Active
1 VBUS +5.1 V -
2 D- USB serial data -
3 D+ USB serial data -
4 SG Signal ground -
Pin No Symbol Name Active
1 +12V +12 V -
2 SG Signal ground -
Pin No Symbol Name Active
1 TIP Not used -
2 RING Not used -
3 8PMJ-3 Not used -
4 8PMJ-1 Not used -
5 8PMJ-6 Not used -
6 8PMJ-2 Not used -
7 8PMJ-7 Not used -
8 8PMJ-4 Not used -
9 8PMJ-8 Not used -
10 8PMJ-5 Not used -
11 LED1 GRNP Not used -
12 LED2 YELP Not used -
13
ENABLE/DIS-
ABLE
Wireless LAN enable signal -
14 LED2 YELN Not used -
15 CHSGND Signal ground -
16 RSV Not used -
17 INTB# Interrupt request-B -
18 +5.1VA +5.1 V -
19 +3.3VA +3.3 V -
20 INTA# Interrupt request-A -
21 RSV Not used -
22 RSV Not used -
23 SG Signa l ground -
24 +3.3VA +3.3 V -
25 CLK PCI clock -
26 RST# Reset signal -
27 SG Signa l ground -
28 +3.3VA +3.3 V -
29 REQ# Data request signal -
30 GNT# Grant -
31 +3.3VA +3.3 V -
32 SG Signa l ground -
33 AD[31] PCI address/data bus [31] -
34 PME# +3.3 V -
35 AD[29] PCI address/data bus [29] -
36 RSV Not used -
37 SG Signa l ground -
38 AD[30] PCI address/data bus [30] -
39 AD[27] PCI address/data bus [27] -
40 +3.3VA +3.3 V -
41 AD[25] PCI address/data bus [25] -
42 AD[28] PCI address/data bus [28] -
43 RSV Not used -
44 AD[26] PCI address/data bus [26] -
45 C/BE(3]# Command and byte enable-3 -
46 AD[24] PCI address/data bus [24] -
47 AD[23] PCI address/data bus [23] -
48 IDSEL Wireless LNA IDselect sIgnal -
49 SG Signa l ground -
50 SG Signa l ground -
51 AD[21] PCI address/data bus [21] -
52 AD[22] PCI address/data bus [22] -
53 AD[19] PCI address/data bus [19] -
54 AD[20] PCI address/data bus [20] -
55 SG Signa l ground -
56 PAR Parity -
57 AD[17] PCI address/data bus [17] -
58 AD[18] PCI address/data bus [18] -
59 C/BE(2)# Command and byte enable-2 -
60 AD[16] PCI address/data bus [16] -
61 IRDY# Initiator ready L
62 SG Signa l ground -
63 +3.3VA +3.3 V -
64 FRAME# Cycle frame L
65 CLKRUN# Signal ground -
66 TRDY# Target ready L
67 SERR# System Error L
68 STOP# Stop L
69 SG Signa l ground -
70 +3.3VA +3.3 V -
71 PERR# Data parity Error L
72 DEVSEL# Device select L
73 C/BE(1)# Command and byte enable-1 -
74 SG Signa l ground -
75 AD[14] PCI address/data bus [14] -
76 AD[15] PCI address/data bus [15] -
77 SG Signa l ground -
78 AD[13] PCI address/data bus [13] -
79 AD[12] PCI address/data bus [12] -
80 AD[11] PCI address/data bus [11] -
81 AD[10] PCI address/data bus [10] -
82 SG Signa l ground -
83 SG Signa l ground -
84 AD[9] PCI address/data bus [9] -
85 AD[8] PCI address/data bus [8] -
86 C/BE(0)# Command and byte enable-0 -
87 AD[7] PCI address/data bus [7] -
88 +3.3VA +3.3 V -
89 +3.3VA +3.3 V -
90 AD[6] PCI address/data bus [6] -
91 AD[5] PCI address/data bus [5] -
92 AD[4] PCI address/data bus [4] -
93 RSV Not used -
94 AD[2] PCI address/data bus [2] -
95 AD[3] PCI address/data bus [3] -
96 AD[0] PCI address/data bus [0] -
97 +5.1VA +5.1 V -
98 RSV WIP Not used -
99 AD[1] PCI address/data bus [1] -
100 RSV WIP Not used -
101 SG Signal ground -
102 SG Signal ground -
103 AC SYNC Signal ground -
104 M66EN PCI bus 66 MHz clock enable signal -
105 AC SDATA IN Not used -
106
AC SDATA
OUT
Signal ground -
107 AC BIT CLK Signal ground -
108
AC CODEC
ID0#
Signal ground -
109
AC CODEC
ID1#
Signal ground -
110 AC RESET# Signal ground -
111
MOD AUDIO
MON
Not used -
112 RSV Not used -
113 AUDIO GND Not used -
114 SG Signal ground -
115
SYS AUDIO
OUT
Not used -
116
SYS AUDIO
IN
Not used -
117
SYS AUDIO
OUT GND
Not used -
118
SYS AUDIO
IN GND
Not used -
119 AUDIO GND Not used -
120 AUDIO GND Not used -
121 RSV Not used -
122 MPCIACT# Not used -
123 VCC5VA Not used -
124 +3.3VA +3.3 V -
Pin No Symbol Name Active
1 +12VA +12 V -
2 SG Signal ground -
3 SG Signal ground -
4 +5.1VA +5.1 V -
Pin No Symbol Name Active
1 +3.3VA +3.3 V -
2 +3.3VA +3.3 V -
3 +3.3VA +3.3 V -
4 SG Signal ground -
5 -12VA -12V -
6 -12VA -12V -
7 +5.1VA +5.1 V -
8 +5.1VA +5.1 V -
9 +3.3VA +3.3 V -
10 IDSEL0 PCI slot-0 IDselect sIgnal -
11 OPBINT(0) Interrupt request-0 -
12 SG Signa l ground -
13 IDSEL0 PCI slot-1 IDselect sIgnal -
14 SG Signa l ground -
15 PCICLK(3) PCI clock-3 -
16 SG Signa l ground -
17 REQ(1)# Data request signal-1 -
18 REQ(0)# Data request signal-0 -
19 +3.3VA +3.3 V -
20 AD[31] PCI address/data bus [31] -
21 AD[29] PCI address/data bus [29] -
22 SG Signa l ground -
23 AD[27] PCI address/data bus [27] -
24 AD[25] PCI address/data bus [25] -
25 +3.3VA +3.3 V -
26 C/BE(3]# Command and byte enable-3 -
27 AD[23] PCI address/data bus [23] -
28 SG Signa l ground -
29 AD[21] PCI address/data bus [21] -
30 AD[19] PCI address/data bus [19] -
31 +3.3VA +3.3 V -
32 AD[17] PCI address/data bus [17] -
33 C/BE(2)# Command and byte enable-2 -
34 SG Signa l ground -
35 IRDY# Initiator ready L
36 +3.3VA +3.3 V -
37 DEVSEL# Device select L
38 SG Signa l ground -
39 LOCK# +3.3 V L
40 PERR# Data parity Error -
41 +3.3VA +3.3 V -
42 SERR# System Error L
43 +3.3VA +3.3 V -
44 C/BE(1)# Command and byte enable-1 -
45 AD[14] PCI address/data bus [14] -
46 SG Signa l ground -
47 AD[12] PCI address/data bus [12] -
48 AD[10] PCI address/data bus [10] -
49 M66EN PCI bus 66 MHz clock enable signal -
50 SG Signa l ground -
51 AD[8] PCI address/data bus [8] -
52 AD[7] PCI address/data bus [7] -
53 +3.3VA +3.3 V -
54 AD[5] PCI address/data bus [5] -
55 AD[3] PCI address/data bus [3] -
56 SG Signa l ground -
57 AD[1] PCI address/data bus [1] -
58 +3.3VA +3.3 V -
59 +5.1VA +5.1 V -
60 SG Signa l ground -
61 +3.3VA +3.3 V -
62 +3.3VA +3.3 V -
63 +3.3VA +3.3 V -
64 SG Signa l ground -
65 +12VA +12 V -
66 +12VA +12 V -
67 +5.1VA +5.1 V -
68 +5.1VA +5.1 V -
69 +3.3VA +3.3 V -
70 OPBINT(1) Interrupt request-1 -
71 +3.3VA +3.3 V -
72 PCIRST# PCI reset signal -
73 +3.3VA +3.3 V -
74 PCICLK(4) PCI clock-4 -
75 +3.3VA +3.3 V -
76 GNT(1)# Grant-1 -
77 GNT(0)# Grant-0 -
78 SG Signa l ground -
79 PME# +3.3 V -
80 AD[30] PCI address/data bus [30] -
81 +3.3VA +3.3 V -
82 AD[28] PCI address/data bus [28] -
83 AD[26] PCI address/data bus [26] -
84 SG Signa l ground -
85 AD[24] PCI address/data bus [24] -
86 +3.3VA +3.3 V -
87 +3.3VA +3.3 V -
88 AD[22] PCI address/data bus [22] -
89 AD[20] PCI address/data bus [20] -
90 SG G round -
91 AD[18] PCI address/data bus [18] -
92 AD[16] PCI address/data bus [16] -
93 +3.3VA +3.3 V -
94 FRAME# Cycle frame L
95 SG Signa l ground -
96 TRDY# Target ready L
97 SG Signa l ground -
98 STOP# Stop L
99 +3.3VA +3.3 V -
100 +3.3VA +3.3 V -
101 SG Signal ground -
102 SG Signal ground -
103 PAR Parity -
104 AD[15] PCI address/data bus [15] -
105 +3.3VA +3.3 V -
106 AD[13] PCI address/data bus [13] -
107 AD[11] PCI address/data bus [11] -
108 SG Signal ground -
109 AD[9] PCI address/data bus [9] -
110 SG Signal ground -
111 C/BE(0)# Command and byte enable-0 -
112 +3.3VA +3.3 V -
113 AD[6] PCI address/data bus [6] -
114 AD[4] PCI address/data bus [4] -
115 SG Signal ground -
116 AD[2] PCI address/data bus [2] -
117 AD[0] PCI address/data bus [0] -
118 +3.3VA +3.3 V -
119 +5.1VA +5.1 V -
120 +5.1VA +5.1 V -
Pin No Symbol Name Active
1 +5.1VB +5.1 V -
2 +5.1VB +5.1 V -
3 SG Signal ground -
4 SG Signal ground -
5 CCDRS CCD RS signal -
6 SG Signal ground -
7 CCDCP CCD CP signal -
8 SG Signal ground -
9 CCDSH CCD SH signal -
10 SG Signal ground -
11 CCDCK2B CCD shift clock-2B -
12 SG Signal ground -
13 CCDCK2A CCD shift clock-2A -
14 SG Signal ground -
15 CCDCK1A CCD shift clock-1A -
16 SG Signal ground -
17 CCD-EVEN CCD even data -
18 SG Signal ground -
19 CCD-ODD CCD odd data -
20 SG Signal ground -
21 AG Analog ground -
22 AG Analog ground -
23 AG Analog ground -
24 +12VB +12 V -
25 +12VB +12 V -
26 +12VB +12 V -
Pin No Symbol Name Active
1 SG Signal ground -
2 PLTN-1A Platen sensor detection signal -
3 +5V +5.1 V -
4 SG Signal ground -
5 HOME-1A Carriage home position sensor detection signal -
6 +5V +5.1 V -
Pin No Symbol Name Active
1 ACK RADF acknowledge signal -
2 SCN-STR VARID signal from RADF -
3 RXD Received serial data -
4 SG Signal ground -
5 TXD RADF transmitted serial data -
6 SG Signal ground -
7 DF-ACK Acknowledge signal from RADF -
8 DF-RRQ Request signal from RADF -
9 REQ RADF request signal -
10 CNT RADF connection detection signal -
Pin No Symbol Name Active
1 PG Power ground -
2 PG Power ground -
3 LMPON-A Exposure lamp ON signal H
4 +24VD4 +24 V -
5 +24VD4 +24 V -
Pin No Symbol Name Active
1 NC Not connected -
2 NC Not connected -
3 NC Not connected -
4 +5VAPS +5 V -
5 APSR Automatic original detection sensor signal -
6 SG Signal ground -
7 +5VAPS +5 V -
8 APSC Automatic original detection sensor signal -
9 SG Signal ground -
10 +5VAPS +5 V -
11 APS3 Automatic original detection sensor signal -
12 SG Signal ground -
13 +5VAPS +5 V -
14 APS2 Automatic original detection sensor signal -
15 SG Signal ground -
16 +5VAPS +5 V -
17 APS1 Automatic original detection sensor signal -
18 SG Signal ground -
Pin No Symbol Name Active
1 SCNM-BB Scan motor drive signal-B -
2 +24VD4 +24 V -
3 SCNM-B Scan motor drive signal-B -
4 SCNM-AB Scan motor drive signal-A -
5 +24VD4 +24 V -
6 SCNM-A Scan motor drive signal-A -
Pin No Symbol Name Active
1 MDT[0] ROM data bus [0] -
2 MDT[2] ROM data bus [2] -
3 MDT[4] ROM data bus [4] -
4 MDT[6] ROM data bus [6] -
5 MRD ROM data read signal -
6 PNLDT[0] D/L address bus [0] -
7 PNLDT[1] D/L address bus [2] -
8 MAD[4] ROM address bus [4] -
9 MAD[6] ROM address bus [6] -
10 MAD[8] ROM address bus [8] -
11 MAD[10] ROM address bus [10] -
12 MAD[12] ROM address bus [12] -
13 MAD[14] ROM address bus [14] -
14 MAD[16] ROM address bus [16] -
15 MAD[18] ROM address bus [18] -
16 SG Signal ground -
17 SG Signal ground -
18 MDT[1] ROM data bus [1] -
19 MDT[3] ROM data bus [3] -
20 MDT[5] ROM data bus [5] -
21 MDT[7] ROM data bus [7] -
22 PNL_CS Chip select signal -
23 PNLDT1 D/L address bus [1] -
24 PNLDT3 D/L address bus [3] -
25 MAD[5] ROM address bus [5] -
26 MAD[7] ROM address bus [7] -
27 MAD[9] ROM address bus [9] -
28 MAD[11] ROM address bus [11] -
29 MAD[13] ROM address bus [13] -
30 MAD[15] ROM address bus [15] -
31 MAD[17] ROM address bus [17] -
32 ROMDT ROM connection detection signal -
33 +5.1VB +5.1 V -
34 LED LED drive signal -
Pin No Symbol Name Active
1 - Exposure lamp high-voltage output -
2 NC Not connected -
3 NC Not connected -
4 - Exposure lamp high-voltage output -
Pin No Symbol Name Active
1 SG Signal ground -
2 +5.1VD + 5.1 V -
3 +5.1VD + 5.1 V -
4 SG Signal ground -
5 WRLVL-1 Laser level control signal (reference voltage) -
6 SG Signal ground -
7 NC Not used -
8 SG Signal ground -
9 PIDT-1 Laser image data (differential signal +) -
10 PIDT-0 Laser image data (differential signal -) -
11 SG Signal ground -
12 WRAPC-0 APC write signal -
13 NC Not used -
14 SHDWM-1 Laser shut down signal -
15 SG Signal ground -
16 +5.1VD + 5.1 V -
17 +5.1VD + 5.1 V -
18 SG Signal ground -
Pin No Symbol Name Active
1 +5.1VD + 5.1 V -
2 SG Signal ground -
3 BDIN-1 Laser beam position detection signal (H-sync) -
Pin No Symbol Name Active
1 PWR-EN Power supply enable signal L
2 PWR-DN AC main power down signal L
3 NC Not connected -
4 NC Not connected -
5 +12VB +12 V -
6 SG Signal ground -
7 +12VA +12 V -
8 SG Signal ground -
9 NC Not connected -
10 SG Signal ground -
11 SG Signal ground -
12 SG Signal ground -
13 +3.3VA +3.3 V -
14 NC Not connected -
15 +3.3VA +3.3 V -
16 +3.3VA +3.3 V -
17 SG Signal ground -
18 SG Signal ground -
19 +3.3VB +3.3 V -
20 +3.3VB +3.3 V -
21 SG Signal ground -
22 SG Signal ground -
23 SG Signal ground -
24 +5.1VA +5.1 V -
25 +5.1VB +5.1 V -
26 +5.1VA +5.1 V -
Pin No Symbol Name Active
1 SG Signal ground -
2 +5.1VD +5.1 V -
3 PG Power ground -
4 PG Power ground -
5 +24VD2 +24 V -
6 +24VD2 +24 V -
7 PG Power ground -
8 PG Power ground -
9 PG Power ground L
10 PG Power ground L
11 +24VD1 +24 V -
12 +24VD1 +24 V -
13 +24VD1 +24 V -
14 +24VD1 +24 V -
15 NC Not connected -
16 NC Not connected -
17 NC Not connected -
18 HTR2ON-1A Side heater ON/OFF signal of fuser roller -
19 HTR1ON-1A Center heater ON/OFF signal of fuser roller -
20 PSPDWN-1 AC main power down signal L
21 SG Signal ground -
22 +12VB +12 V -
23 SG Signal ground -
24 SG Signal ground -
25 SG Signal ground (to FUS board) -
26 +5.1VB +5.1 V (to FUS board) -
27 +5.1VB +5.1 V -
28 +5.1VB +5.1 V -
29 SG Signal ground -
30 +3.3VB +3.3 V -
Pin No Symbol Name Active
1 NC Not connected -
2 NC Not connected -
3 SG Signal ground -
4 +5.1VB +5.1 V (to FINISHER) -
5 NC Not connected -
6 NC Not connected -
7 PG Signal ground -
8 +24VD5 +24 V (to FINISHER) -
9 PG Power ground -
10 PG Power ground -
11 +24VD2 +24 V (to ADU) -
12 +24VD2 +24 V (to ADU) -
13 PG Power ground -
14 PG Power ground -
15 +24VD1 +24 V (to main motor) -
16 +24VD1 +24 V (to main motor) -
Pin No Symbol Name Active
1 SG Signal ground -
2 SG Signal ground -
3 +5.1VB +5.1 V -
4 +5.1VB +5.1 V -
5 +5.1VB +5.1 V (to RADF) -
6 +5.1VB +5.1 V (to RADF) -
7 SG Signal ground -
8 SG Signal ground -
9 +3.3VB +3.3 V -
10 +3.3VB +3.3 V -
11 SG Signal ground -
12 SG Signal ground -
13 +12VB +12 V -
14 SG Signal ground -
15 NC Not connected -
16 NC Not connected -
17 SG Signal ground -
18 SG Signal ground -
19 +24VD4 +24 V -
20 +24VD4 +24 V -
21 PG Power ground -
22 PG Power ground -
23 +24VD3 +24 V (to RADF) -
24 +24VD3 +24 V (to RADF) -
Pin No Symbol Name Active
1 - High-voltage to main needle electrode charger -
Pin No Symbol Name Active
1 - High-voltage to main charger grid -
Pin No Symbol Name Active
1 - High-voltage to developer charger bias -
Pin No Symbol Name Active
1 - High-voltage to transfer charger bias -
Pin No Symbol Name Active
1 - High-voltage to separation charger bias -
Pin No Symbol Name Active
1 -
High-voltage to transfer guide bias and registra-
tion roller bias
-
Pin No Symbol Name Active
1 YD Y-axis touch position detection terminal-D -
2 KL X-axis touch position detection terminal-L -
3 XR X -axis touch position detection terminal-R -
4 YU Y-axis touch position detection terminal-U -
Pin No Symbol Name Active
1 CCFL+ High-voltage terminal -
2 NC Not connected -
3 CCFL- High-voltage terminal -
Pin No Symbol Name Active
1 FRAME LCD scanning line start signal -
2 LAOD LCD data latch pulse -
3 CP LCD data transmission clock -
4 SG Signal ground -
5 +5.1VA +5.1 V -
6 SG Signal ground -
7 VEE Ground -
8 D.OFF LCD enable signal -
9 D0 LCD display data-0 -
10 D1 L CD display data-1 -
11 D2 LCD display data-2 -
12 D3 L CD display data-3 -
Pin No Symbol Name Active
1 LDFC-1 LED driver output-1 L
2 LDFC-2 LED driver output-2 L
3 LDFC-4 LED driver output-4 L
4 LDFC-5 LED driver output-5 L
5 LDFC-6 LED driver output-6 L
6 LDFC-7 LED driver output-7 L
7 LDFC-8 LED driver output-8 L
8 LDFC-9 LED driver output-9 L
9 LDFC-10 LED driver output-10 L
10 LDFC-11 LED driver output-11 L
11 LDFC-12 LED driver output-12 L
12 LDFC-13 LED driver output-13 L
13 LDFC-15 LED driver output-15 L
14 LDON0 LED common driver signal-0 H
15 LDON1 LED common driver signal-1 H
16 SG S ignal ground -
Pin No Symbol Name Active
1 SCN15 Button scanning signal-5 -
2 SCN14 Button scanning signal-4 -
3 SCN13 Button scanning signal-3 -
4 SCN12 Button scanning signal-2 -
5 SCN11 Button scanning signal-1 -
6 RET0 Button scanning return signal-0 -
7 RET1 Button scanning return signal-1 -
8 RET2 Button scanning return signal-2 -
9 RET3 Button scanning return signal-3 -
10 RET8 Button scanning return signal-8 -
11 RET9 B utton scanning return signal-9 -
Pin No Symbol Name Active
1 SG Signal ground -
2 ADUFL ADU exit sensor detection signal -
3 +5.1VB + 5.1 V -
Pin No Symbol Name Active
1 SG Signal ground -
2 ADUFU ADU entrance sensor detection signal -
3 +5.1VB + 5.1 V -
Pin No Symbol Name Active
1 +24VD2 +24 V -
2 FDMA ADU motor drive signal-A -
3 FDMB ADU motor drive signal-B -
4 FDMC A DU motor drive signal-C -
5 FDMD A DU motor drive signal-D -
6 +24VD2 +24 V -
Pin No Symbol Name Active
1 SG Signal ground -
2 COVSW ADU opening/closing detection signal -
Pin No Symbol Name Active
1 TXOUT Transmitted FAX data -
2 RXIN Received FAX data -
3 CML CML relay drive signal -
4 LD Dial pulse drive signal -
5 EXTRG RG relay drive signal -
6 ATT3DB -3 db ATT exchange signal -
7 RLADJ1 MODEM select signal -
8 RLADJ2 MODEM select signal -
9 RGCLK Ring clock -
10 AG A nalog ground -
11 -12VB -12 V -
12 AG A nalog ground -
13 +12VB +12 V -
14 +24VB +24 V -
15 16Hz Ring clock -
16 AG A nalog ground -
17 CI Ring signal detection L
18 ANSDET FAX data answer detection L
19 REVA Line 1 External telephone hook detection signal L
20 REVB Line 1 External telephone hook detection signal L
21 INTHOOK Internal telephone hook signal -
22 EXTHOOK External telephone hook signal -
23 +5.1VA +5.1 V -
24 AG A nalog ground -
25 +5VA +5 V -
26 -12VB -12 V -
27 AG A nalog ground -
28 +12VB +12 V -
29 +24VB +24 V -
30 PG Power ground -
Pin No Symbol Name Active
1 TXB Transmitted FAX data -
2 RXIN Received FAX data -
3 CML CML relay drive signal -
4 LD Dial pulse drive signal -
5 ER/HK Not used -
6 ATT3DB -3 db ATT exchange signal -
7 RLADJ1 Modem select signal -
8 RLADJ2 Modem select signal -
9 RGCLK Not used
10 AG S ignal ground -
11 -12VB -12 V -
12 AG A nalog ground -
13 +12VB +12 V -
14 NC Not connected -
15 16Hz Not used -
16 AG A nalog ground -
17 CI Ring signal detect L
18 ANSDET FAX data answer detection L
19 REVA Line 2 External telephone hook detection signal -
20 REVB Line 2 External telephone hook detection signal -
21 NC Not connected -
22 NC Not connected -
23 +5.1VA +5.1 V -
24 AG A nalog ground -
25 +5VA +5 V -
26 -12VB -12 V -
27 AG A nalog ground -
28 +12VB +12 V -
29 NC Not connected -
30 NC Not connected -
Pin No Symbol Name -
1 SP+ Speaker output (+) -
2 SP- Speaker output (-) -
Pin No Symbol Name Active
1 TXOUT2 Transmitted data -
2 +5VA +5 V -
3 +12VB +12 V -
4 +3.3VB +3.3 V -
5 MOD2DMA-1 Mo dem 2 DMA signal -
6 SG Signal ground -
7 MEM2CS-0 SRAM chip select signal -
8 +5.1VB +5.1 V -
9 MEMRD2-0 SRAM data read signal -
10 CLKOE-1 Clock out enable signal -
11 TXEN2-1 TX enable signal -
12 +5.1VB +5.1 V -
13 A[16] MDM address bus [16] -
14 A[14] MDM address bus [14] -
15 A[12] MDM address bus [12] -
16 A[10] MDM address bus [10] -
17 A[8] MDM address bus [8] -
18 A[6] MDM address bus [6] -
19 A[4] MDM address bus [4] -
20 A[2] MDM address bus [2] -
21 A[0] MDM address bus [0] -
22 +5.1VB +5.1 V -
23 CEP1RST-0 CEP1 reset signal -
24 +5.1VB +5.1 V -
25 SG S ignal ground -
26 CEPCLK System clock signal -
27 SG S ignal ground -
28 D[0] MDM data bus [0] -
29 D[2] MDM data bus [2] -
30 D[4] MDM data bus [4] -
31 D[6] MDM data bus [6] -
32 D[8] MDM data bus [8] -
33 D[10] MDM data bus [10] -
34 D[12] MDM data bus [12] -
35 D[14] MDM data bus [14] -
36 SG S ignal ground -
37 MOD2DET-0 Modem 2 detection signal -
38 SG S ignal ground -
39 DREQC2-1 Data request signal -
40 DACKC2-0 Data acknowledge signal -
41 RXIN2 Received data -
42 AG A nalog ground -
43 -12VB -12 V -
44 AG A nalog ground -
45 MOD2INT-1 Modem 2 interrupt signal -
46 MOD2CS-0 Modem 2 chip select signal -
47 MOD2RST-0 Modem 2 reset signal -
48 SG S ignal ground -
49 RXEN2-1 RX enable signal -
50 MEMWRH2-0 SRAM high byte write signal -
51 MEMWRL2-0 SRAM low byte write signal -
52 A[18] MDM address bus [18] -
53 A[17] MDM address bus [17] -
54 A[15] MDM address bus [15] -
55 A[13] MDM address bus [13] -
56 A[11] MDM address bus [11] -
57 A[9] MDM address bus [9] -
58 A[7] MDM address bus [7] -
59 A[5] MDM address bus [5] -
60 A[3] MDM address bus [3] -
61 A[1] MDM address bus [1] -
62 CPURST-0 CPU reset signal -
63 CEP2INT-1 CEP2 interrupt signal -
64 +5.1VB +5.1 V -
65 +5.1VB +5.1 V -
66 IORD2-0 MDM data read signal -
67 IOWR2-0 MDM data write signal -
68 D[1] MDM data bus [1] -
69 D[3] MDM data bus [3] -
70 D[5] MDM data bus [5] -
71 D[7] MDM data bus [7] -
72 D[9] MDM data bus [9] -
73 D[11] MDM data bus [11] -
74 D[13] MDM data bus [13] -
75 D[15] MDM data bus [15] -
76 +5.1VB +5.1 V -
77 +5.1VB +5.1 V -
78 CEP2CS-0 CEP2 chip select signal -
79 DREQD2-1 Data request signal -
80 DACKD2-0 Data acknowledge signal
Pin No Symbol Name Active
1 D[0] ROM data bus [0] -
2 D[2] ROM data bus [2] -
3 D[4] ROM data bus [4] -
4 D[6] ROM data bus [6] -
5 RD-0 ROM data read signal -
6 A[0] ROM address bus [0] -
7 A[2] ROM address bus [2] -
8 A[4] ROM address bus [4] -
9 A[6] ROM address bus [6] -
10 A[8] ROM address bus [8] -
11 A[10] ROM address bus [10] -
12 A[12] ROM address bus [12] -
13 A[14] ROM address bus [14] -
14 A[16] ROM address bus [16] -
15 A[18] ROM address bus [18] -
16 SG S ignal ground -
17 SG S ignal ground -
18 D[1] ROM data bus [1] -
19 D[3] ROM data bus [3] -
20 D[5] ROM data bus [5] -
21 D[7] ROM data bus [7] -
22 BOOTCS-0 Chip select signal -
23 A[1] ROM address bus [1] -
24 A[3] ROM address bus [3] -
25 A[5] ROM address bus [5] -
26 A[7] ROM address bus [7] -
27 A[9] ROM address bus [9] -
28 A[11] ROM address bus [11] -
29 A[13] ROM address bus [13] -
30 A[15] ROM address bus [15] -
31 A[17] ROM address bus [17] -
32 ROMDET0-0 Download board connection detection signal L
33 +5.1VB +5.1 V -
34 LEDDL-0 External ROM loading status signal L
Pin No Symbol Name Active
1 RXD Receiver serial data -
2 SG Signal ground -
3 TXD Transmitted serial data -
4 SG Signal ground -
5 NC Not connected -
6 NC Not connected -
7 NC Not connected -
8 NC Not connected -
9 F-CNT Finisher connection detection signal L
10 CNT-GND Ground -
10.5 Connector Table (e-STUDIO202L/232/282)
05/11
To Next Page
Loading...
