Toshiba e-STUDIO2303A - Page 550

05/08 Mode Element Sub element Item Subitem Code
Sub-
code
Details
Default
value
Acceptable
value
SRAM Contents
Proce
dure
20L
/
23L/
25L
20H
/
23H/
25H
08 Setting
mode
Process Fuser Fuser roller
temperature during
printing (Center
thermistor)
2049 - Thick paper 1 8 0-14 M 0: 140 degrees C 1: 145 degrees C 2: 150 degrees C 3:
155 degrees C 4: 160 degrees C 5: 165 degrees C 6: 170
degrees C 7: 175 degrees C 8: 180 degrees C 9: 185
degrees C 10: 190 degrees C 11: 195 degrees C 12: 200
degrees C 13: 205 degrees C 14: 210 degrees C
1YY
08 Setting
mode
Process Fuser Fuser roller
temperature during
printing (Center
thermistor)
2050 - Thick paper 2 13 0-14 M 0: 140 degrees C 1: 145 degrees C 2: 150 degrees C 3:
155 degrees C 4: 160 degrees C 5: 165 degrees C 6: 170
degrees C 7: 175 degrees C 8: 180 degrees C 9: 185
degrees C 10: 190 degrees C 11: 195 degrees C 12: 200
degrees C 13: 205 degrees C 14: 210 degrees C
1YY
08 Setting
mode
Process Fuser Fuser roller
temperature during
printing (Center
thermistor)
2051 - OHP film 8 0-14 M 0: 140 degrees C 1: 145 degrees C 2: 150 degrees C 3:
155 degrees C 4: 160 degrees C 5: 165 degrees C 6: 170
degrees C 7: 175 degrees C 8: 180 degrees C 9: 185
degrees C 10: 190 degrees C 11: 195 degrees C 12: 200
degrees C 13: 205 degrees C 14: 210 degrees C
1YY
08 Setting
mode
Process Fuser 1st printing pre-
running operating
time
2052 - OHP film 0 0-15 M 0: Invalid 1: 1sec 2: 2sec 3: 3sec 4 : 4sec 5: 5sec
6: 6sec 7: 7sec 8: 8sec 9: 9sec 10: 10sec 11:
12sec 12: 14sec 13 : 16sec 14: 18sec 15: 20sec
1YY
08 Setting
mode
Process Fuser 1st printing pre-
running operating
time
2053 - Plain paper-low temp.
environment
0 0-15 M 0: Invalid 1: 1sec 2: 2sec 3: 3sec 4 : 4sec 5: 5sec
6: 6sec 7: 7sec 8: 8sec 9: 9sec 10: 10sec 11:
12sec 12: 14sec 13 : 16sec 14: 18sec 15: 20sec
1YY
08 Setting
mode
Process Fuser 1st printing pre-
running operating
time
2054 - Thick paper 1 10 0-15 M 0: Invalid 1: 1sec 2: 2sec 3: 3sec 4 : 4sec 5: 5sec
6: 6sec 7: 7sec 8: 8sec 9: 9sec 10: 10sec 11:
12sec 12: 14sec 13 : 16sec 14: 18sec 15: 20sec
1YY
08 Setting
mode
Process Fuser 1st printing pre-
running operating
time
2055 - Tthick paper 2 10 0-15 M 0: Invalid 1: 1sec 2: 2sec 3: 3sec 4 : 4sec 5: 5sec
6: 6sec 7: 7sec 8: 8sec 9: 9sec 10: 10sec 11:
12sec 12: 14sec 13 : 16sec 14: 18sec 15: 20sec
1YY
08 Setting
mode
Process Fuser 2075 - Ready and preheat
pre-running operating
frequency
4 0-6 M 0: Not controlled 1: 0.5h 2: 1.0h 3: 1.5h 4: 2.0h 5:
2.5h 6: 3.0h
1YY
e-STUDIO2006/2306/2506/2007/2307/2507
SELF-DIAGNOSIS CODE (03/04/05/08 CODE)
14-1-30
© 2013-2017 TOSHIBA TEC CORPORATION All rights reserved