Toshiba e-STUDIO3511 - Machine Noise Information

November 2003 © TOSHIBA TEC iii e-STUDIO3511/4511 CONTENTS
3.12.7 Adjustment of reverse solenoid .......................................................................... 3-65
3.12.8 Adjustment of RADF opening/closing switch ..................................................... 3-67
3.12.9 Adjustment of RADF opening/closing sensor .................................................... 3-68
3.12.10 Adjustment of tray volume ................................................................................. 3-69
3.13 Adjustment of the Finisher (MJ-1022) .............................................................................. 3-70
3.13.1 Adjusting the jogging plate width ....................................................................... 3-70
3.13.2 Adjusting the angle of the jogging plate ............................................................. 3-72
3.13.3 Adjusting the overlap of the sensor flag ............................................................. 3-73
3.13.4 Adjusting the tension of the stack processing motor belt ................................... 3-74
3.13.5 Releasing the stack tray guide lever fixing plate ................................................ 3-76
3.13.6 Adjustment of the upper tray angle .................................................................... 3-77
3.13.7 DIP switch functions........................................................................................... 3-79
3.14 Adjustment of the Finisher (MJ-1023/1024) ..................................................................... 3-81
3.14.1 Adjusting the alignment position (Finisher unit) ................................................. 3-81
3.14.2 Adjusting the staple position (Finisher unit) ....................................................... 3-82
3.14.3 Adjusting the folding position (Saddle stitcher unit) ........................................... 3-84
3.14.4 Fine adjustment of binding/folding position (Saddle stitcher unit) ...................... 3-87
3.14.5 Sensor output adjustment (Puncher unit) .......................................................... 3-87
3.14.6 Registering the number of punch holes (Puncher unit) ...................................... 3-88
3.15 Key Copy Counter (MU-8, MU-10) ................................................................................... 3-89
3.16 Adjustment of Transfer Belt Deviation .............................................................................. 3-91
3.16.1 Outline ............................................................................................................... 3-91
3.16.2 Transfer belt deviation ....................................................................................... 3-91
3.16.3 Adjustment procedure ........................................................................................ 3-92
4. PREVENTIVE MAINTENANCE (PM) ............................................................................ 4-1
4.1 PM Support Mode ..............................................................................................................4-1
4.1.1 General description .............................................................................................. 4-1
4.1.2 Operational flow and operational screen ............................................................. 4-1
4.1.3 Work flow of parts replacement ........................................................................... 4-6
4.2 General Descriptions for PM Procedure ............................................................................ 4-7
4.3 Operational Items in Overhauling....................................................................................... 4-7
4.4 Preventive Maintenance Checklist ..................................................................................... 4-8
4.5 PM KIT ............................................................................................................................. 4-23
4.6 Jig List .............................................................................................................................. 4-24
4.7 Grease List ....................................................................................................................... 4-24
4.8 Precautions for Storing and Handling Supplies ................................................................ 4-25
4.8.1 Precautions for storing TOSHIBA supplies ........................................................ 4-25
4.8.2 Checking and cleaning of photoconductive drum .............................................. 4-26
4.8.3 Checking and cleaning of drum cleaning blade and
transfer belt cleaning blade .......................................................... 4-27
4.8.4 Handling of drum cleaner brush ......................................................................... 4-27
4.8.5 Handling of transfer belt ..................................................................................... 4-27
4.8.6 Checking and cleaning of fuser belt and pressure roller .................................... 4-27
4.8.7 Checking and replacing the oil roller and cleaning roller.................................... 4-28
05/03