Toshiba E-STUDIO520 - Page 211

© 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 185
2
Pickup roller
(Tandem LCF)
1288-0,1,2,8 1289 <Default value of code 1288
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 400,000/400,000/
400,000/400,000
Pickup roller
(1st drawer)
1290-0,1,2,8 1291 <Default value of code 1290
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 200,000/200,000/
200,000/200,000
Pickup roller
(2nd drawer)
1292-0,1,2,8 1293 <Default value of code 1292
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 200,000/200,000/
200,000/200,000
Pickup roller
(Option LCF)
1294-0,1,2,8 1295 <Default value of code 1294
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 500,000/500,000/
500,000/500,000
Feed roller
(Tandem LCF)
1296-0,1,2,8 1297 <Default value of code 1296
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 400,000/400,000/
400,000/400,000
Feed roller
(1st drawer)
1298-0,1,2,8 1299 <Default value of code 1298
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 200,000/200,000/
200,000/200,000
Feed roller
(2nd drawer)
1300-0,1,2,8 1301 <Default value of code 1300
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 200,000/200,000/
200,000/200,000
Feed roller
(Option LCF)
1302-0,1,2,8 1303 <Default value of code 1302
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 500,000/500,000/
500,000/500,000
Separation roller
(Tandem LCF)
1304-0,1,2,8 1305 <Default value of code 1304
(e-STUDIO520/600/720/850) or
(e-STUDIO523/603/723/853)>
Sub-codes 0, 2, 8: 0/0/0/0
Sub-code 1: 400,000/400,000/
400,000/400,000
Items
PM management set-
ting <Procedure 4>
*Indicated in 8 digits
Date of previous
replacement
<Procedure 2>
Remarks
07/11