Toshiba e-studio555 - Page 71

2
© 2009 - 2011 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO555/655/755/855
OUTLINE OF THE MACHINE
2 - 35
S52 CST4-FEED-SNR
4th drawer feed sensor
Detecting the paper feeding status of the
4th drawer
(Only for JPC model of all equipments)
Fig. 2-21 7-18
S53 PLTN-SNR
Platen sensor
Detecting the opening/closing status of the
RADF
Fig. 2-5
Fig. 2-6
35-21
S71 LCF-BTM-SNR
Tandem LCF bottom
sensor
Detecting the lowering status of the tray in
the tandem LCF
(Only for NAD/SAD/ARD/ASD/AUD/MJD/
CND/TWD model of all equipments)
Fig. 2-22 8-14
S72 LCF-MST-SNR
Standby side mis-stacking
sensor
Detecting the paper mis-stacking at the
standby side of the tandem LCF
(Only for NAD/SAD/ARD/ASD/AUD/MJD/
CND/TWD model of all equipments)
Fig. 2-22 8-14
S73 LCF-ENDF-HP-SNR
End fence home position
sensor
Detecting the end fence home position in
the tandem LCF
(Only for NAD/SAD/ARD/ASD/AUD/MJD/
CND/TWD model of all equipments)
Fig. 2-22 8-14
S74 LCF-EMP-SNR
Standby side empty sensor
Detecting the presence of the paper at the
standby side of the tandem LCF
(Only for NAD/SAD/ARD/ASD/AUD/MJD/
CND/TWD model of all equipments)
Fig. 2-22 9-37
S75 LCF-ENDF-STP-SNR
End fence stop position
sensor
Detecting the end fence stop position in the
tandem LCF
(Only for NAD/SAD/ARD/ASD/AUD/MJD/
CND/TWD model of all equipments)
Fig. 2-22 8-14
SW1 FSR-SW
Fuser detection switch
Supplying or shutting off AC power to the
damp heater according to the installation
status of the fuser unit
(Not installed: Shut off)
Fig. 2-11 24-9
SW2 TNR-SW
Toner cartridge detection
switch
Detecting the presence of the toner
cartridge
Fig. 2-12 45-18
SW3 DEV-SW
Developer unit detection
switch
Detecting the presence of the developer
unit
Fig. 2-14 5-16
SW4 CH-CLN-POS-SW
Wire cleaner position
detection switch
Detecting the stop position of the charger
wire cleaner
Fig. 2-14 39-13
SW5 EXIT-COV-SW
Exit cover switch
Detecting the opening/closing status of the
left lower cover
Fig. 2-17 15-11
SW6 MAIN-SW
Main switch
Turning the power of the equipment ON/
OFF
Fig. 2-18 29-11
SW7 U-FRNT-COV-SW
Front cover switch
Detecting the opening/closing status of the
front cover (upper)
Fig. 2-18 29-108
SW8 COV-INTLCK-SW
Cover interlock switch
Supplying or shutting off AC power to the
switching regulator (voltage-generating
circuit interlocked with these covers)
according to the opening/closing status of
the front cover (lower) or left lower cover
(Cover open: Shut off)
Fig. 2-18 29-24
SW9 IH-INTLCK-SW
IH interlock switch
Supplying or shutting off AC power to the
heater control PC board (IH board)
according to the opening/closing status of
the front cover (lower) or left lower cover
(Cover open: Shut off)
Fig. 2-18 29-24
SW11 TNR-MOT-INTLCK-SW
Toner motor interlock
switch
Supplying or shutting off 24 V voltage to the
new toner supply motor (M5) according to
the opening/closing status of the front
cover (upper)
(Cover open: Shut off)
Fig. 2-18 29-109
SR1 Original tray sensor Detects the length of the original set on the
original tray.
Fig. 2-28 93-2
SR2 Original tray width sensor Detects the width of the original set on the
original tray.
Fig. 2-28 93-12
Symbol Name Function Remarks P-I