Toshiba e-STUDIO656 - Page 20

e-STUDIO556/656/756/856(Ver03) © 2012 TOSHIBA TEC CORPORATION All rights reserved
CONTENTS
10
9.2.2 HDD fault diagnosis ........................................................................................... 9-9
9.2.3 Precautions and procedures when replacing the HDD.................................... 9-11
9.2.4 Precautions and Procedures when replacing the SYS board.......................... 9-16
9.2.5 Procedures and settings when replacing the SLG board ................................ 9-19
9.2.6 Precautions and Procedures when replacing SRAM board............................. 9-20
9.2.7 Precautions and Procedures when replacing NVRAM .................................... 9-25
9.2.8 Firmware confirmation after the PC board/HDD replacement ......................... 9-29
9.2.9 License re-registration using the one-time dongle........................................... 9-30
9.3 Precautions for Installation of GP-1070 and Disposal of HDD/Board ............................. 9-32
9.3.1 Precautions for Installation of GP-1070 ........................................................... 9-32
9.3.2 Precautions when disposing of the HDD ......................................................... 9-32
9.3.3 Precautions when disposing of the SYS board................................................ 9-32
9.3.4 Precautions when disposing of the SRAM board ............................................ 9-32
9.4 Re-registration of the Electronic License Key with the one-time dongle ......................... 9-33
9.4.1 Outline ............................................................................................................. 9-33
9.4.2 Re-registration method .................................................................................... 9-33
9.4.3 Re-registration method when the equipment is replaced due to
a malfunction ................................................................................................... 9-33
10. REMOTE SERVICE..................................................................................................... 10-1
10.1 Auto Supply Order...........................................................................................................10-1
10.1.1 Outline ............................................................................................................. 10-1
10.1.2 Setting Item...................................................................................................... 10-2
10.1.3 Setting procedure ............................................................................................ 10-4
10.1.4 Order Sheet Format....................................................................................... 10-14
10.2 Service Notification .......................................................................................................10-16
10.2.1 Outline ........................................................................................................... 10-16
10.2.2 Setting............................................................................................................ 10-17
10.2.3 Items to be notified ........................................................................................ 10-23
11. FIRMWARE UPDATING ............................................................................................. 11-1
11.1 General description.........................................................................................................11-1
11.2 Firmware Updating with USB Media ............................................................................... 11-5
11.2.1 Master data / System ROM / Laser ROM / PFC ROM / Engine ROM /
Scanner ROM / RADF ROM............................................................................ 11-7
11.3 Patch Updating with USB Media................................................................................... 11-21
11.3.1 Master data / System ROM ........................................................................... 11-23
11.4 Firmware Updating with PWA-DWNLD-350-JIG1......................................................... 11-27
11.4.1 Writing the data to the download jig (PWA-DWNLD-350-JIG1)..................... 11-28
11.4.2 System ROM ................................................................................................. 11-30
11.5 Firmware Updating with K-PWA-DLM-320.................................................................... 11-32
11.5.1 Laser ROM .................................................................................................... 11-33
11.5.2 Engine ROM / PFC ROM............................................................................... 11-35
11.5.3 Scanner ROM ................................................................................................ 11-37
11.5.4 RADF firmware .............................................................................................. 11-40
11.5.5 Finisher firmware (MJ-1027/1028/1029)........................................................ 11-42
11.5.6 Saddle stitcher firmware (MJ-1028/1029)...................................................... 11-44
11.5.7 Inserter firmware (MJ-7001) .......................................................................... 11-46
11.5.8 Fax unit firmware (GD-1250) ......................................................................... 11-48
11.6 Confirmation of the updated data.................................................................................. 11-50
11.7 When Firmware Updating Fails..................................................................................... 11-51
11.7.1 Procedure ...................................................................................................... 11-51
11.7.2 Flow chart for correcting USB update failure ................................................. 11-52
12. BACKUP FUNCTION.................................................................................................. 12-1
12.1 Data Cloning ................................................................................................................... 12-1
12.1.1 General description.......................................................................................... 12-1
12.1.2 Precautions...................................................................................................... 12-1
12.1.3 Backup files ..................................................................................................... 12-1
12.1.4 Cloning procedure ........................................................................................... 12-2