8
© 2012 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO556/656/756/856(Ver03)
ERROR CODE AND TROUBLESHOOTING
8 - 9
E775 RADF jam Original reading end sensot paper remaining jam P. 8-68
E777 Original exit sensor paper remaining jam P. 8-68
E860 Original jam access cover open: The Original jam
access cover has opened during RADF operation.
P. 8 - 6 9
E870 RADF open jam: RADF has opened during RADF
operation.
P. 8 - 6 9
E871 Cover open jam in the read ready status: Jam
caused by opening of the Original jam access cover
or front cover while the RADF is waiting for the
scanning start signal from the equipment.
P. 8 - 6 9
E890 ADF time out jam P. 8-69
E9F0 Finisher jam
(Puncher section)
Hole punch jam: Hole punching is not performed
properly.
P. 8 - 7 0
EA10 Finisher jam
(Finisher section)
Paper transport delay jam: Paper which has passed
the exit sensor does not reach the inlet sensor.
P. 8 - 7 0
EA20 Paper transport stop jam: Paper which has reached
the inlet sensor does not pass the inlet sensor.
P. 8 - 7 1
EA30 Power-ON jam: Paper is remaining at the inlet
sensor when the power is turned ON.
P. 8 - 7 2
EA40 Door open jam: The upper cover or the front cover
of the Finisher has opened, or the upper door or the
front door of the Hole Punch Unit has opened
during printing.
P. 8 - 7 3
EA50 Stapling jam: Stapling is not performed properly. P. 8-74
EA60 Early arrival jam: The inlet sensor detects paper
earlier than the specified timing.
P. 8 - 7 4
EA80 Finisher jam
(Saddle Stitcher
section)
Stapling jam: Stapling is not performed properly. P. 8-75
EA90 Door open jam: The delivery cover or the inlet cover
has opened during printing.
P. 8 - 7 6
EAA0 Power-ON jam: Paper is remaining at the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper
sensor, vertical path paper sensor or delivery
sensor when the power is turned ON.
P. 8 - 7 7
EAB0 Paper transport stop jam: Paper which has passed
the inlet sensor does not reach or pass the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper
sensor or delivery sensor.
P. 8 - 7 8
EAC0 Transport delay jam: Paper which has reached the
inlet sensor does not pass the inlet sensor.
P. 8 - 7 9
EAD0 Other paper jam Print end command time-out jam: The printing has
not finished normally due to the communication
error between the SYS board and LGC board at the
end of the printing.
P. 8 - 8 3
EAE0 Finisher jam Receiving period time-out jam: The printing cannot
be finished normally due to the communication
error between the equipment and the Finisher when
the paper is transported from the equipment to the
Finisher.
P. 8 - 8 3
EB30 Ready period time-out jam: The equipment judges
that the paper transport to the Finisher is disabled
due to the communication error between the
equipment and the Finisher at the start of the
printing.
P. 8 - 8 4
EB50 Paper transport jam Paper remaining on the transport path: The multiple
feeding of the preceding paper caused the
misfeeding of the upcoming paper.
P. 8 - 5 4
EB60 Paper remaining on the transport path: The multiple
feeding of the preceding paper caused the
misfeeding of the upcoming paper (= redetection
after no jam is detected at [EB50]).
P. 8 - 5 5
Error code Classification Contents Troubleshooting
To Next Page
Loading...
