Toshiba GR200 Series - Page 683

6F2S1914 (0.49)
GRL200 (Soft 033 & 037)
- 660 -
“SPOS01_SL_BO_FLG”
(510001_8501011F76)
BIO module
BO2
“SPOS01_OEX_BO”
(510001_8201011DD3)
“BO2-RB”
(200B01_8102011113)
BO3
“SPOS01_FEX_BO”
(510001_8101011DD0)
“BO3-RB”
(200B01_8202021113)
SW2 is driven with
BO2 at IO#1
SW3 is driven with
BO3 at IO#1
Plus (+)
SW 3
SW 2
Minus (−)
43SW
On
Command
Off
Command
SW1 is not driven with
any BO1
SW 1
Plus (+)
Physical BO is
virtualized.
Remote/Local end
Select
command
ON/OFF
Operate-On
command
Operate-Off
command
Figure 4.1-39 Contact health check setting and 43SW diagram for example #3
Table 4.1-25 PLC monitoring points (Output signal for event suppression function in SPOSxx)
Signal Number
Signal Name
Description
510001 0001011001
SPOS01_STATE
Status of SPOS01
510001 0001021001
SPOS02_STATE
Status of SPOS02
510001 0001031001
SPOS03_STATE
Status of SPOS03
….
….
….
510001 0001141001
SPOS20_STATE
Status of SPOS20
510001 8101011F59
SPOS01_F_QLT_SPP
Event suppression detected (SPOS01)
510001 8101021F59
SPOS02_F_QLT_SPP
Event suppression detected (SPOS02)
510001 8101031F59
SPOS03_F_QLT_SPP
Event suppression detected (SPOS03)
….
….
….
510001 8101141F59
SPOS20_F_QLT_SPP
Event suppression detected (SPOS20)
Table 4.1-26 PLC monitoring points (Output of select signal in SPOSxx)
Signal Number
Signal Name
Description
510001 8501011F76
SPOS01_SL_BO_FLG
Select command signal in SPOS01
510001 8501021F76
SPOS02_SL_BO_FLG
Select command signal in SPOS02
510001 8501031F76
SPOS03_SL_BO_FLG
Select command signal in SPOS03
….
….
….
510001 8501141F76
SPOS20_SL_BO_FLG
Select command signal in SPOS20
Table 4.1-27 PLC monitoring points (Output of operate signal in SPOSxx)
Signal Number
Signal Name
Description
510001 8201011DD3
SPOS01_OEX_BO
SPOS01 operate (ON) command for Binary Output.
510001 8201021DD3
SPOS02_OEX_BO
SPOS02 operate (ON) command for Binary Output.
510001 8201031DD3
SPOS03_OEX_BO
SPOS03 operate (ON) command for Binary Output.
…
…
…
510001 8201141DD3
SPOS20_OEX_BO
SPOS20 operate (ON) command for Binary Output.
510001 8101011DD0
SPOS01_FEX_BO
SPOS01 operate (OFF) command for Binary Output.
510001 8101021DD0
SPOS02_FEX_BO
SPOS02 operate (OFF) command for Binary Output.
510001 8101031DD0
SPOS03_FEX_BO
SPOS03 operate (OFF) command for Binary Output.
…
….
….