Toshiba GR200 Series - Page 754

6F2S1914 (0.49)
GRL200 (Soft 033 & 037)
- 731 -
◆ Signal monitoring points in DPSY01
DPSY(Function ID: 511001)
Element ID
Name
Description
3102011F95
DPSY01_OT3_SIGNAL
DPSY01 operation time3 reset signal
3102011D36
DPSY01_OT3_VAL
DPSY01 operation time3 value
3102011F97
DPSY01_OT4_SIGNAL
DPSY01 operation time4 reset signal
3102011D39
DPSY01_OT4_VAL
DPSY01 operation time4 value
8002011F98
DPSY01_RE_EC_LCD
DPSY01 reset time execute command by LCD
8002011D7B
DPSY01_RE_EC_OWS
DPSY01 reset time execute command by OWS(HMI)
8002011D7C
DPSY01_RE_EC_RCC
DPSY01 reset time execute command by RCC
8002011D7D
DPSY01_RE_EC_RMT
DPSY01 reset time execute command by Remote
8002011F9A
DPSY01_RE_SC_LCD
DPSY01 reset time select command by LCD
8002011D78
DPSY01_RE_SC_OWS
DPSY01 reset time select command by OWS(HMI)
8002011D79
DPSY01_RE_SC_RCC
DPSY01 reset time select command by RCC
8002011D7A
DPSY01_RE_SC_RMT
DPSY01 reset time select command by Remote
8602011F8E
DPSY01_RST_CS07
DPSY01 reset time selected fail condition signal
0002011F57
DPSY01_RST_SIG
DPSY01 Reset time signal
8002011D54
DPSY01_SC_LCD
DPSY01 select command by LCD
8002011D51
DPSY01_SC_OWS
DPSY01 select command by OWS(HMI)
8002011D52
DPSY01_SC_RCC
DPSY01 select command by RCC
8002011D53
DPSY01_SC_RMT
DPSY01 select command by Remote
8002011F5A
DPSY01_SC_ST_ERR
DPSY01 select command mode err
0002011F55
DPSY01_SEL_SIG
DPSY01 Selected signal
8502011F89
DPSY01_SE_RCV_RMTCN
DPSY01 count change selected fail condition signal check
8502011F8D
DPSY01_SE_RCV_RMTRS
DPSY01 reset time selected fail condition signal check
8002011E76
DPSY01_SLD_CS
DPSY01 selected condition signal
8002011F67
DPSY01_SLD_CS04
DPSY01 selected condition signal 04
8102011F68
DPSY01_SLD_CS05
DPSY01 selected condition signal 05
8202011F69
DPSY01_SLD_CS06
DPSY01 selected condition signal 06
8A02011F88
DPSY01_SLD_CSCN
DPSY01 count change selected condition signal
8A02011F8C
DPSY01_SLD_CSRS
DPSY01 reset time selected condition signal
0002011D90
DPSY01_SLD_RPT
DPSY01 selected signal(stSeld) for SAS
8E02011F5D
DPSY01_SLD_TMO
DPSY01 time out after selected
8A02011F9F
DPSY01_SLD_TMOCN
DPSY01 count change time out after selected
8A02011FA5
DPSY01_SLD_TMORS
DPSY01 reset time out after selected
8102011E7B
DPSY01_SLF_CS
DPSY01 no direction select fail condition signal
8702011E98
DPSY01_SLF_FCT_EIS
DPSY01 select fail factor signal except interlock/synchronism check
8802011F9D
DPSY01_SLF_FCT_F03CN
DPSY01 count change select fail factor signal by fixedlogic 03
8802011FA3
DPSY01_SLF_FCT_F03RS
DPSY01 reset time select fail factor signal by fixedlogic 03
8702011F9E
DPSY01_SLF_FCT_F04CN
DPSY01 count change select fail factor signal by fixedlogic 04
8702011FA4
DPSY01_SLF_FCT_F04RS
DPSY01 reset time select fail factor signal by fixedlogic 04
8302011F9C
DPSY01_SLF_FCT_F07CN
DPSY01 count change selected timer for a check
8302011FA2
DPSY01_SLF_FCT_F07RS
DPSY01 reset time selected timer for a check
8602011F63
DPSY01_SLF_FCT_FLG03
DPSY01 select fail factor signal by fixedlogic 03
8702011F64
DPSY01_SLF_FCT_FLG04
DPSY01 select fail factor signal by fixedlogic 04
8502011F65
DPSY01_SLF_FCT_FLG05
DPSY01 select fail factor signal by fixedlogic 05
8802011F6C
DPSY01_SLF_FCT_FLG07
DPSY01 selected timer for a check
8002011E7D
DPSY01_SLR_CS
DPSY01 select release condition signal
8302011D02
DPSY01_ST_OFF
DPSY01 Normal open state
8102011D03
DPSY01_ST_ON
DPSY01 Normal close state
8C02011E4B
DPSY01_SYNC_OPT_TRIG
DPSY01 start to synchronizing
8D02011E4A
DPSY01_SYNC_SEL_TRIG
DPSY01 start to check voltage condition(Dead or Live)
8202011ED1
DPSY01_SYNEN
DPSY01 Synchronism Check Apply or Bypass
0002011D95
DPSY01_TMP_02
DPSY01 time reset selected signal(stSeld) for SAS
3102011D80
DPSY01_TMP_06
DPSY01 control event data (selected)
3102011D81
DPSY01_TMP_07
DPSY01 control event data (select fail)