Toshiba MMY-MAP0724FT9UT - Way Cassette Type; Ceiling Type

EN
–12–
6 Push the button to finish the setting.
* F1 appears in the CODE No. section on the
remote control. This indicates that the louver 01
shown in the following figure is selected.
NOTE
Even in louver lock mode, the louver temporarily moves
in the following cases:
• When the air conditioner is stopped
• When heating starts
• When defrosting
• When thermo. off.
◆ Releasing the louver lock
Set “0000” in Step 4 of “Setting the louver lock”.
The mark disappears.
* Steps 1 - 3 and 5, 6 of “Setting
the louver lock” also apply to
releasing the lock.
◆ Adjusting the horizontal direction
1 Push and hold the and “TEMP. ”
buttons for at least 4 seconds while running
is stopped.
blinks.
“01” appears in CODE No.
2 Push the button (left side of the button)
to select a unit
The unit number changes each time the button is
pushed.
The fan of the selected unit runs, and the louver
swings.
3 Push the “TEMP. ” buttons to
change the CODE No. to “45”.
4 Push the “TIME ”buttons to select a
direction.
5 Push the button to check the settings.
The indicator stops blinking and stays lit, and the
settings are confirmed.
6 Push button to finish the setting.
* If the cold draft position is selected, the ceiling
smudging reduction effect will be reduced.
0001 - 0005
(Louver position
code)
Louver No.
0000
SET DATA
Direction SET
DATA
Direction setting
“0000”
Smudging reduction position
(reduces ceiling smudging)
“0002”
Cold draft preventive position
(Prevent cold draft)
[Factory default]
UNIT LOUVER
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
Unit No.
1-4
No display
 4-way cassette type
• The louver automatically closes when running is
stopped.
• In pre-heating mode, the louver points upward.
The swing indication appears on the remote control
even in pre-heating mode, but the actual swing starts
only after pre-heating is complete.
▼ 2-way and 3-way air discharge
The air discharge can be changed to the 2-way or 3-
way type to suit the room shape and style.
For details, contact the dealer where you purchased
the air conditioner.
 Ceiling type
Vertical adjustment
• The louver automatically points upward when
running is stopped.
• In pre-heating mode, the louver points upward.
The swing indication appears on the remote control
even in pre-heating mode, but the actual swing starts
only after pre-heating is complete.
Horizontal adjustment
◆ Unit select
• When two or more indoor units are controlled with
one remote control, the louver direction can be set
for each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time the (left side of the button) is
pushed, the indication changes as follows:
▼ When cooling
Point the louver horizontally.
▼ When heating (for heat-pump model only)
Point the louver downward.
▼ When cooling
Point the louver horizontally to send cool air across the
entire room.
▼ When heating (for heat-pump model only)
Point the louver downward to send heated air to the
floor.
When adjusting louver direction horizontally, point the
vertical grille inside the horizontal louver in preferred
direction.
UNIT LOUVER
UNIT LOUVER
Unit No.
1-4
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
23-EN 24-EN
+00EH99943901_00Ta.book Page 12 Thursday, May 23, 2013 7:17 PM