P9 ASD Installation and Operation Manual 251
Table 9. Output Terminal Assignments, My Function Input Setting Assignments, and Parameter/Input
Setting Numbers for the FLA/B/C, O1A/O1B (OUT1), O2A/O2B (OUT2), OUT3 – OUT6, and R1 – R4.
Discrete Output Terminal Assignment Selections
Input
Setting
Param.
Setting
Function
Input
Setting
Param.
Setting
Function
1000 0 Lower-Limit Frequency 1096 96 Specified Data Output 3
1002 2 Upper-Limit Frequency 1098 98 Specified Data Output 4
1004 4 Low-Speed Signal 1100 100 Specified Data Output 5
1006 6 Acceleration/Deceleration Completion 1102 102 Specified Data Output 6
1008 8 Speed Reach Signal 1104 104 Specified Data Output 7
1010 10 Failure FL (All Trips) 1106 106 Light Load
1012 12 Failure FL (Except EF, OCL, EPHO, OL2) 1108 108 Heavy Load
1014 14 Over-Current (OC) Alarm 1110 110 Positive Torque Limit
1016 16 ASD Overload (OL1) Alarm 1112 112 Negative Torque Limit
1018 18 Motor Overload (OL2) Alarm 1114 114 External Rush Suppression Relay Activated
1020 20 Over-Heat Alarm 1118 118 Completion of Stop Positioning
1022 22 Over-Voltage Alarm 1120 120 L-STOP
1024 24 Main Circuit (MOFF) Under-Voltage Alarm 1122 122 Power Failure Synchronized Operation
1026 26 Low-Current Alarm 1124 124 Traverse in Progress
1028 28 Over-Torque Alarm 1126 126 Traverse Deceleration Active
1030 30 DBR Overload Alarm 1128 128 Part Replacement Alarm
1032 32 Emergency Off Active 1130 130 Over-Torque Alarm
1034 34 Retry Active 1132 132 Frequency Command ½ Selection
1036 36 Pattern Operation Switching Output 1134 134 Failure FL (Except Emergency Off)
1038 38 PID Deviation Limit 1136 136 External Device 1
1040 40 Run/Stop 1138 138 External Device 2
1042 42 Serious Failure (OCA, OCL, EF, Phase Failure, etc.) 1140 140 External Device 3
1044 44 Light Failure (OL, OC1, 2, 3, OP) 1142 142 External Device 4
1046 46 Commercial Power/ASD Switching Output 1 1144 144 External Device 5
1048 48 Commercial Power/ASD Switching Output 2 1146 146 External Device 6
1050 50 Cooling Fan On/Off 1148 148 Sealing Water
1052 52 Jogging Operation Active (Jog Run Active) 1150 150 NPSH/No Flow Alarm
1054 54 Panel/Terminal Board Operation Switching 1154 154 TBA Active
1056 56 Cumulative Run-time Alarm 1156 156 TBA Alarm Float
1058 58 ProfiBus/DeviceNet/CC-Link Communication Error 1222 222 My Function Output 1
1060 60 Forward/Reverse Switching 1224 224 My Function Output 2
1062 62 Ready for Operation 1 1226 226 My Function Output 3
1064 64 Ready for Operation 2 1228 228 My Function Output 4
1068 68 Brake Release (BR) 1230 230 My Function Output 5
1070 70 Alarm Status Active 1232 232 My Function Output 6
1072 72 Forward Speed Limit (Torque Control) 1234 234 My Function Output 7
1074 74 Reverse Speed Limit (Torque Control) 1236 236 My Function Output 8
1076 76 ASD Healthy Output 1238 238 My Function Output 9
1078 78 RS485 Communication Error 1240 240 My Function Output 10
1080 80 Error Code Output 1 1242 242 My Function Output 11
1082 82 Error Code Output 2 1244 244 My Function Output 12
1084 84 Error Code Output 3 1246 246 My Function Output 13
1086 86 Error Code Output 4 1248 248 My Function Output 14
1088 88 Error Code Output 5 1250 250 My Function Output 15
1090 90 Error Code Output 6 1252 252 My Function Output 16
1092 92 Specified Data Output 1 1254 254 Always Off
1094 94 Specified Data Output 2
To Next Page
Loading...
