1
Press
FIX
: Move the louver in the
desired vertical direction.
2
Press
SWING
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust manually.
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push CLOCK
•
by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
2. Press
ON
or
OFF
: adjust the time.
3. Press
SET
: Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button (PRESET)
% One-Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
( Power selection button (POWER-SEL)
) Quiet button (QUIET)
~ Comfort sleep button (COMFORT SLEEP)
+ Filter reset button (FILTER)
, Clock Reset button (CLOCK)
- Check button (CHK)
Press the “ONE-TOUCH” button for fully automated operation that is customized
to the typical consumer preferences in your region of the world. The customized
settings control temperature air fl ow strength, air fl ow direction and other settings
to provide you alternate contact with “ONE-TOUCH” of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
Press
ONE-TOUCH
: Start the operation.
To automatically select cooling or fan only operation
1. Press
MODE
: Select A.
2. Press
TEMP
: Set the desired temperature.
1. Press
MODE
: Select Cool or Fan only .
2. Press
TEMP
: Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED , MED+ , or
HIGH
.
For dehumidifi cation, a moderate cooling performance is controlled automatically.
1. Press
MODE
: Select Dry .
2. Press
TEMP
: Set the desired temperature.
To automatically control room temperature and airfl ow for faster cooling operation
(except in DRY and FAN ONLY mode)
Press
Hi-POWER
: Start and stop the operation.
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 24°C and fan operation is
automatic speed.
Set the timer when the air conditioner is operating.
PRESET
ONE-TOUCH
QUIET
SWING
TIMER
ON
FILTER
CHK
CLOCK
OFF
CLR
SLEEP
SET
FIX
Hi-POWER
POWER-SEL
COMFORT
SLEEP
MODE
TEMP
FAN
Setting the ON Timer Setting the OFF Timer
1
Press
ON
:
Set the desired ON timer.
Press
OFF
:
Set the desired OFF timer.
2
Press
SET
: Set the timer. Press
SET
: Set the timer.
3
Press
CLR
: Cancel the timer.
Press
CLR
: Cancel the timer.
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
1
Press
ON
: Set the ON timer.
3
Press
SET
.
2
Press
OFF
: Set the OFF timer.
4
Press
SET
: button during the
(
or ) mark fl ashing.
• During the every day timer is activating, both arrows (
, ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
This function is used when its circuit breaker is shared with other electrical
appliances. It limits the maximum current/ power consumption to 100%, 75%
or 50%. The lower the percentage, the higher the saving and also the longer
the compressor lifetime.
Press
POWER-SEL
: Select (for 100%), (for 75%), (for 50%)
• When the level is selected, PWR-SEL level fl ashes on LCD display for 3
seconds. In case of 75% and 50% level, number “75” or “50” also fl ashes
for 2 seconds.
• Due to the reason that POWER SELECT FUNCTION limits the maximum
current, inadequate cooling capacity may occur.
COOLING / FAN ONLY OPERATION
7
DRY OPERATION
8
Hi-POWER OPERATION
9
POWER-SELECTION OPERATION
10
TEMPORARY OPERATION
11
TIMER OPERATION
12
PREPARATION BEFORE USE
2
AIR FLOW DIRECTION
3
REMOTE CONTROL
4
ONE-TOUCH
5
AUTOMATIC OPERATION
6
To Next Page
Loading...
