Toshiba RAS-22PAVSG-E - PREPARATION BEFORE USE; Preparing Filters; AIR FLOW DIRECTION

1
2 3 4
SWING
FAN
FIX FIX
Hi POWER ECO
COMFORT
SLEEP
AIR FLOW
1
#
4
6
5
(
%
"
9
!
-
~
2
3
7
$
&
8
)
,
+
INDOOR UNIT DISPLAY
1
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
Push
by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
AIR FLOW DIRECTION
3
Note:
●
The provided Remote Controller is a wireless type, which also can be
used as a wire. Please see “How to Connect The Remote Controller
for Wired Operation”, located in installation instruction, in case of wired
control is required.
●
In wire operation, remote controller will return to initial condition
(PRESET, TIMER and CLOCK will return to initial condition) when user
shutdown power supply of Air conditioner.
REMOTE CONTROL
4
1
Infrared signal emitter
2
Start/Stop button
3
Mode select button (MODE)
4
Temperature button (TEMP)
5
Fan speed button (FAN)
6
Swing louver button (SWING)
7
Set louver Up-Down button (FIX X)
8
On timer button (ON)
9
Off timer button (OFF)
!
Setup button (SET)
"
Clear button (CLR)
#
Memory and Preset button (PRESET)
$
AIR FLOW selection button (AIR FLOW)
%
High power button (Hi-POWER)
&
Economy button (ECO)
(
Set louver Left-Right button (FIX W)
)
Comfort sleep button (COMFORT SLEEP)
~
Filter reset button (FILTER)
+
Set clock button (CLOCK)
,
Check button (CHECK)
-
Reset button (RESET)
AUTOMATIC OPERATION
5
To automatically select cooling, heating, or fan only operation
1. Press
02'(
: Select A.
2. Press
: Set the desired temperature.
3. Press
)$1
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet .
1. Press
02'(
: Select Cool , Heat , or Fan only .
2. Press
: Set the desired temperature.
Cooling: Min. 17°C, Heating: Max. 30°C,
Fan Only: No temperature indication
3. Press
)$1
: Select AUTO, LOW , LOW+ , MED ,
MED+
, HIGH or Quiet .
COOLING / HEATING / FAN ONLY
OPERATION
6
DRY OPERATION
7
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press
02'(
: Select Dry .
2. Press : Set the desired temperature.
Hi-POWER OPERATION
8
To automatically control room temperature and airfl ow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
+L32:(5
: Start and stop the operation.
1
Eco (White)
2
Hi-Power (White)
3
Timer (White)
4
Operation mode
- Cool (Blue)
- Heat (Orange)
1
Press
),;
: Move the louver
in the desired vertical direction.
2
Press
FIX
: Move the
louver in the desired horizontal
direction.
3
Press
6:,1*
: For select
louver swing operation.
Vertical
(Up-Down)
Swing
Horizontal
(Left-Right)
Swing
Swing off
Up-Down
Left-Right
Swing
Pi Pi
Pi
Pi Pi
●
Vertical (Up-Down) swing
●
Horizontal (Left-Right) swing
4
Press
AIR FLOW
: To select provided air fl ow direction
Wide
center
Spot
left
Wide
left
Spot
center
Wide
right
Spot
right
Return to
manually setting
“Pi” sound when air fl ow direction is set and “Pi Pi” sound when
air fl ow direction is canceled and return to manually setting.
Note:
●
Do not move the louver manually by hands or others.
●
The louver may automation positioning by some operation mode.
● Display brightness can be adjusted, follow procedure on ".