Toshiba TEC B-SX4T Series - PRINTER INSTALLATION; NOTE FOR OPTIONAL EQUIPMENT INSTALLATION;MAJOR UNIT REPLACEMENT;MAINTENANCE

EO18-33012B
(Revision Date: Feb. 15, 2007)
TABLE OF CONTENTS
Page
1. UNPACKING-------------------------------------------------------------------------------------------------------- 1- 1
1.1 PROCEDURES ---------------------------------------------------------------------------------------------------1- 1
1.2 CHECKS ------------------------------------------------------------------------------------------------------------1- 3
2. PRINTER INSTALLATION-------------------------------------------------------------------------------------- 1- 3
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION
/MAJOR UNIT REPLACEMENT/MAINTENANCE---------------------------------------------------- 3- 1
3.1 OPENING/CLOSING THE TOP COVER-------------------------------------------------------------------3- 3
3.2 REMOVING THE SIDE PANEL (L) --------------------------------------------------------------------------3- 3
3.3 OPENING/CLOSING THE PRINTER BLOCK ------------------------------------------------------------3- 4
3.4 REMOVING THE OPERATION PANEL --------------------------------------------------------------------3- 5
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT ------------------------------------- 4- 1
4.1 SWING CUTTER (B-4205-QM) -------------------------------------------------------------------------------4- 4
4.2 ROTARY CUTTER (B-8204-QM)-----------------------------------------------------------------------------4- 7
4.3 STRIP MODULE (B-9904-H-QM) ---------------------------------------------------------------------------4-13
4.4 RIBBON SAVING MODULE (B-9904-R/R2-QM)--------------------------------------------------------4-19
4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) ----------------------------------------------------4-22
4.6 USB INTERFACE BOARD (B-9700-USB-QM) ----------------------------------------------------------4-25
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) -----------------------------------------------------------4-29
4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) ---------------------------------------------4-33
4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) --------------------4-35
4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) -------------------------------------------------------4-43
4.10.1 Applicable Model ------------------------------------------------------------------------------------------ 4-43
4.10.2 Packing List ------------------------------------------------------------------------------------------------- 4-43
4.10.3 Removing the Platen Frame Top and Attaching the Ribbon Guide --------------------------- 4-45
4.10.4 Attaching the Antenna------------------------------------------------------------------------------------ 4-48
4.10.5 Attaching the RFID Module ----------------------------------------------------------------------------- 4-51
4.10.6 Parameter Setting and Operation Check for the RFID Module -------------------------------- 4-54
4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R)-----------------------------------------------------------4-56
4.11.1 Applicable Model ------------------------------------------------------------------------------------------ 4-56
4.11.2 Packing List ------------------------------------------------------------------------------------------------- 4-56
4.11.3 Attaching the Antenna to the Antenna Cover or Antenna Frame ------------------------------ 4-59
4.11.4 Attaching the RFID Module to the RFID Plate------------------------------------------------------ 4-59
4.11.5 Attaching the RFID Module ----------------------------------------------------------------------------- 4-63
4.11.6 Parameter Setting and Operation Check for the RFID Module -------------------------------- 4-67
4.12 SWING CUTTER (B-4205-QM-QM-R)---------------------------------------------------------------------4-68
4.12.1 Applicable Model ------------------------------------------------------------------------------------------ 4-68
4.12.2 Packing List ------------------------------------------------------------------------------------------------- 4-68
4.12.3 Installation Procedure ------------------------------------------------------------------------------------ 4-68
4.13 ROTARY CUTTER (B-8204-QM-R) ------------------------------------------------------------------------4-79
4.13.1 Applicable Model ------------------------------------------------------------------------------------------ 4-79
4.13.2 Packing List ------------------------------------------------------------------------------------------------- 4-79
4.13.3 Installation Procedure ------------------------------------------------------------------------------------ 4-79
Mantenimiento Periféricos Informáticos C/Canteras,15 28860 Paracuellos de Jarama Madrid Tel: 91 748 16 04 www.mpi.com.es