EO18-33012B
(Revision Date: May 22, 2009)
4.25 RFID MODULE (B-SX704-RFID-U2-CN-R) ------------------------------------------------------------ 4-209
4.25.1 Applicable Model -----------------------------------------------------------------------------------------4-210
4.25.2 Packing List ------------------------------------------------------------------------------------------------4-211
4.25.3 Installation Procedure -----------------------------------------------------------------------------------4-212
4.25.4 RFID Module Setting ------------------------------------------------------------------------------------4-230
4.25.5 AGC Threshold Setting ---------------------------------------------------------------------------------4-234
4.26 IDENTIFICATION OF THE RFID MODULE (B-SX704-RFID-U2-US/EU/AU/CN-R) ---------------4-237
5. SYSTEM MODE---------------------------------------------------------------------------------------------------- 5- 1
5.1 OPERATION PANEL --------------------------------------------------------------------------------------------5- 1
5.2 OVERVIEW --------------------------------------------------------------------------------------------------------5- 2
5.3 SELF-DIAGNOSTIC TEST-------------------------------------------------------------------------------------5- 3
5.3.1 Printing Mode Selection----------------------------------------------------------------------------------- 5- 4
5.3.2 Dispensing Mode Selection ------------------------------------------------------------------------------ 5- 4
5.3.3 Maintenance Counter/Parameter Settings Printing Out------------------------------------------- 5- 5
5.3.4 Self-Diagnostic Test and Result Print Out----------------------------------------------------------- 5-12
5.3.5 Print Head Element Check ------------------------------------------------------------------------------ 5-17
5.4 PARAMETER SETTING ---------------------------------------------------------------------------------------5-18
5.4.1 Character Code Selection ------------------------------------------------------------------------------- 5-19
5.4.2 Zero Font Code Selection ------------------------------------------------------------------------------- 5-22
5.4.3 Baud Rate Selection-------------------------------------------------------------------------------------- 5-23
5.4.4 Data Length Selection------------------------------------------------------------------------------------ 5-23
5.4.5 Stop Bit Selection------------------------------------------------------------------------------------------ 5-23
5.4.6 Parity Selection -------------------------------------------------------------------------------------------- 5-24
5.4.7 Transmission Control Code Selection ---------------------------------------------------------------- 5-24
5.4.8 LCD Message Selection --------------------------------------------------------------------------------- 5-25
5.4.9 Auto Forward Wait Selection --------------------------------------------------------------------------- 5-25
5.4.10 Forward/Backward Feed Action Selection ---------------------------------------------------------- 5-26
5.4.11 Head Up Cut/Rewinder Selection --------------------------------------------------------------------- 5-26
5.4.12 Solenoid Type Selection--------------------------------------------------------------------------------- 5-27
5.4.13 Ribbon Saving Function Selection -------------------------------------------------------------------- 5-27
5.4.14 Control Code Selection ---------------------------------------------------------------------------------- 5-28
5.4.15 Strip Wait Status Selection------------------------------------------------------------------------------ 5-29
5.4.16 FEED Key Function Selection-------------------------------------------------------------------------- 5-29
5.4.17 KANJI Code Selection------------------------------------------------------------------------------------ 5-30
5.4.18 EURO Code Selection ----------------------------------------------------------------------------------- 5-30
5.4.19 Auto Print Head Check Selection---------------------------------------------------------------------- 5-31
5.4.20 Centronics Interface ACK/BUSY Timing Selection------------------------------------------------ 5-31
5.4.21 Web Printer Function Selection ------------------------------------------------------------------------ 5-32
5.4.22 Input Prime Selection------------------------------------------------------------------------------------- 5-33
5.4.23 Ribbon Near End Selection ----------------------------------------------------------------------------- 5-33
5.4.24 Expansion I/O Interface Selection--------------------------------------------------------------------- 5-33
5.4.25 Centronics Interface Selection ------------------------------------------------------------------------- 5-34
5.4.26 Plug & Play Selection------------------------------------------------------------------------------------- 5-34
5.4.27 Label End/Ribbon End Selection ---------------------------------------------------------------------- 5-34
5.4.28 Pre-Strip Selection ---------------------------------------------------------------------------------------- 5-36
5.4.29 Back Feed Speed Selection ---------------------------------------------------------------------------- 5-36
5.4.30 Maxi Code Specification Selection -------------------------------------------------------------------- 5-36
5.4.31 Print Head Type Selection ------------------------------------------------------------------------------ 5-37
5.4.32 System Mode Password Setting----------------------------------------------------------------------- 5-38
5.4.33 XML Function Setting (Supported only by V4.4A or Xx.x.) -------------------------------------- 5-40
Mantenimiento Periféricos Informáticos C/Canteras,15 28860 Paracuellos de Jarama Madrid Tel: 91 748 16 04 www.mpi.com.es
To Next Page
Loading...
