Toshiba VF-PS1 - Page 255

K-13
E6581386
11
[14] Functions for lift Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0324 Drooping output filter 0.1~200.0 rad/s (Enabled if =3 or 7) 0.1/0.1 100.0 Enabled ●/● - - 6. 16
[15] Commercial/inverter switching function Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0354
Commercial power/inverter switching output selection
0:Disabled 1:Automatic switching in the event of a trip 2:Commercial power switching frequency setting 3:Commercial power switching frequency setting +
automatic switching in the event of a trip
1/1 0 Disabled ●/●●●6. 17
 0355
Commercial power/inverter switching frequency
0~ Hz 0.1/0.01 *2 Enabled ●/●●●6. 17
 0356 Inverter-side switching waiting time 0.10~10.00 sec. 0.01/0.01 *1 Enabled ●/●●●6. 17  0357
Commercial power-side switching waiting time
0.40~10.00 sec. 0.01/0.01 0.62 Enabled ●/●●●6. 17
 0358
Commercial power switching frequency holding time
0.10~10.00 sec. 0.01/0.01 2.00 Enabled ●/●●●6. 17
*1: Default values vary depending on the capacity. ⇒ See the table of K-41. *2: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
[16] PID control [1/2] Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0359 PID control switching
0:No PID control 1:Process type PID control (temp./pressure, etc.)
operation
2:Speed type PID control (potentiometer, etc.)
operation
1/1 0 Disabled ●/●●●6. 18 *1
 0360
PID control feedback control signal selection
0:Deviation input (no feedback input) 1:VI/II (voltage/current input) 2:RR/S4 (potentiometer/voltage input) 3:RX (voltage input) 4:Optional AI1 (differential current input) 5:Optional AI2 (voltage/current input) 6: PG feedback option
1/1 0 Disabled ●/●●●6. 18 *1
 0361 Delay filter 0.0~25.0 1/1 0.1 Enabled ●/●●●6. 18 *1  0362 Proportional (P) gain 0.01~100.0 0.01/0.01 0.10 Enabled ●/●●●6. 18 *1  0363 Integral (I) gain 0.01~100.0 0.01/0.01 0.10 Enabled ●/●●●6. 18 *1  0364 PID deviation upper limit ~ Hz 0.1/0.01 *2 Enabled ●/●●●6. 18 *1
*1: ⇒ For details, refer to Instruction Manual (E6581329) specified in Section 6.36. *2: Inverter with a model number ending with -WN: 60.0 -WP: 50.0