12
定期保养 - 吐皂口
（续）
PERIODIC MAINTENANCE - Nozzle
(Continued)
小孔有4个
4 small holes
6.将在热水中浸泡的滤网取出，使用牙刷清
洗堵塞滤网的皂液及灰尘。
Remove the filter from the hot water, and
use a toothbrush or something similar to
remove any soap or grime clogging the
filter.
7.将在热水中浸泡的吐皂口取出，使用φ1左
右的金属丝（例如回形针）清除堵塞吐皂
口小孔的皂液或灰尘。
Remove the nozzle from the hot water. Use
a bent paper clip or something similar to
remove any soap or grime blocking the
holes.
8.清洁后，按照原样安装。
使用六角扳手拧紧螺钉。
Reattach the nozzle once it has been cleaned.
Fasten the screw securely by tightening with
the hex key.
Note
After attaching the nozzle, use the
dispenser to check that soap does not leak
out along the nozzle.
提示
安装吐皂口后，请使皂液器喷出皂液以确认是
否有皂液从吐皂口外侧漏出。
吐皂口的安装方法
How to attach
the nozzle
牙刷
Toothbrush
滤网
Filter
扳直的回形针
Bent paper clip
清洗后，请使用干燥的软布擦拭滤网上的水分。
Rinse the filter and dry it with a soft cloth.
请插入吐皂口，直至看不见螺钉孔为止，并使用六
角扳手拧紧螺钉。
请确认吐皂口是否安装牢固（不能拉出或脱落）。
Insert the nozzle into the spout until the screw hole is
hidden.
Pull gently on the nozzle to make sure that it does not
come off.
小孔有4个。
The nozzle has 4 small holes.
Caution
N.B. Always attach the nozzle with the
vent facing downwards, otherwise the
soap will go everywhere.
插入吐皂口，直至
看不见螺钉孔为止
Insert the nozzle
until the screw hole
is hidden
注意
请务必将吐皂口朝下安装。
以免导致皂液飞溅。
13
定期保养 - 吐皂口
（续）
PERIODIC MAINTENANCE - Nozzle
(Continued)
4.捏住滤网，从吐皂口中取出滤网。
Pinch the filter and pull it out from the nozzle.
5.将吐皂口和取出的滤网用热水浸泡几分钟。
Leave the nozzle and the filter to soak in hot
water for a few minutes.
Note
This makes it easier to remove any soap that
has adhered to them.
提示
用热水浸泡，易于清除吐皂口及滤网上附着的皂
液。
向身边拉出
Pull toward you
取下
Remove
滤网
Filter
螺丝
Screw
松开
Loosen
吐皂口
Nozzle
请务必将十字形螺丝刀确实插到底并小心地
松开螺丝。否则会出现十字孔变形或空转的
现象。
If you try to force the screw loose without fully
inserting the Phillips head screwdriver, the head
of the screw may be deformed and the
screwdriver will turn freely without doing anything.
Therefore, make sure the screwdriver is fully
inserted before trying to loosen the screw.
3.螺丝松开后,拉出吐皂口拆下。
When the screw is completely loose, pull the
nozzle out to remove it.
[ TLK0800**型的情形 ]
[ For the TLK0800** model ]
灰尘堵塞吐皂口会导致皂液无法喷出，请定期清洁吐皂口。
Clean the nozzle regularly as the soap cannot come out if the nozzle is blocked.
1.拔下电源插头。
Unplug from the power outlet.
2.用十字形螺丝刀松开螺丝拆下。
(用十字形螺丝刀大约旋转十圈)
Use a Phillips head screwdriver to loosen
and remove the screw.
(Turn the screwdriver about 10 turns.)
注意
在洗面器内进行清洗时，请事先堵上排水口。
以免因部件太小而丢失。
Caution
If you are going to wash the nozzle in a sink,
make sure that you put the plug in first.
The parts are small enough to go down the plug
hole and get lost.
To Next Page
Loading...
Need help?
General
