14
定期保养 - 吐皂口
（续）
PERIODIC MAINTENANCE - Nozzle
(Continued)
小孔有4个
4 small holes
6.将在热水中浸泡的滤网取出，使用牙刷清
洗堵塞滤网的皂液及灰尘。
Remove the filter from the hot water, and
use a toothbrush or something similar to
remove any soap or grime clogging the
filter.
7.将在热水中浸泡的吐皂口取出，使用φ1左
右的金属丝（例如回形针）清除堵塞吐皂
口小孔的皂液或灰尘。
Remove the nozzle from the hot water. Use
a bent paper clip or something similar to
remove any soap or grime blocking the
holes.
8.清洗后，装回到原状。
用十字形螺丝刀牢牢地拧紧螺丝。
After cleaning, put the nozzle and the filter
back together.
Tighten the screw securely with the Phillips
head screwdriver.
Note
After attaching the nozzle, use the
dispenser to check that soap does not leak
out along the nozzle.
提示
安装吐皂口后，请使皂液器喷出皂液以确认是
否有皂液从吐皂口外侧漏出。
吐皂口的安装方法
How to attach
the nozzle
牙刷
Toothbrush
滤网
Filter
扳直的回形针
Bent paper clip
清洗后，请使用干燥的软布擦拭滤网上的水分。
Rinse the filter and dry it with a soft cloth.
插入吐皂口端面，直至碰触到喷口本体为止，然后用
十字形螺丝刀拧紧。
拉出吐皂口，以确认不会脱落。
Insert the nozzle until its end is touching the main body of
the spout and tighten it with the Phillips head screwdriver.
Pull on the nozzle to confirm that it will not come out.
小孔有4个。
The nozzle has 4 small holes.
Caution
N.B. Always attach the nozzle with the
vent facing downwards, otherwise the
soap will go everywhere.
插入吐皂口端面，直至
碰触到喷口本体为止。
Insert the nozzle until its
end touches the main
body of the spout.
注意
请务必将吐皂口朝下安装。
以免导致皂液飞溅。
15
定期保养 - 吐皂口
（续）
PERIODIC MAINTENANCE - Nozzle
(Continued)
[ TLK09001G型的情形 ]
[ For the TLK09001G model ]
灰尘堵塞吐皂口会导致皂液无法喷出，请定期清洁吐皂口。
Clean the nozzle regularly as the soap cannot come out if the nozzle is blocked.
1.用专用工具取下吐皂口。
Remove the nozzle using a special tool.
2.拉出吐皂口和滤网。
Pull out the nozzle and the filter.
3.清洗(用水洗) 吐皂口和滤网。
Clean the nozzle and the filter with water.
4.清洗后，装回到原状。
After cleaning, reassemble the parts as they
were.
注意
在洗面器内进行清洗时，请事先堵上排水口，
以免因部件太小而丢失。
Caution
If you are going to wash the nozzle and the filter
in a sink, make sure that you put the plug in first.
The parts are small enough to go down the plug
hole and get lost.
取下吐皂口时，请注意避免专用工具或开闭工具
损伤感应器表面。
When removing the nozzle, be careful not to
damage the sensor surface with the special tool or
a general-purpose tool.
清洗后请用干软布擦拭水分。
用热水浸泡，更易于清除附着的污垢。
After washing the nozzle and the filter in water,
wipe off any water on them with a soft and dry
cloth.
If you soak them in hot water, they can be cleaned
more easily.
吐皂口
Nozzle
感应器
Sensor
松开
Loosen
吐皂口
Nozzle
专用工具
Special tool
滤网
Filter
To Next Page
Loading...
Need help?
General
