150Mbps Wireless N Mini Pocket Router
MODEL NO. TL-WR710N
Package Contents
QIG
150Mbps Wireless N Mini Pocket Router
MODEL NO. TL-WR710N
Resource CD
Ethernet Cable
TL-WR710N
Quick Installation Guide
7106504220 REV1.0.0
For Windows 8
Click the icon at the bottom of your screen,
and a network list will appear at the right side of
your screen. Select your target network, and
then click Connect.
3 4
The screen will appear as shown below. Enter
the network security key, and then click Next.
Instant Wireless Connection
Physical Description
Hardware Connection
Wireless Router Mode (Default)
As the supplement of wired LAN, TL-WR710N
enables the wired LAN to connect to the
Internet wirelessly.
As a wireless router, TL-WR710N create an
instant private wireless network and share
Internet to multiple Wi-Fi devices.
Access Point Mode
2
1
After hardware connection, please write down the
Wireless Password and SSID on the label of your
Router for later use. Both are case-sensitive.
SSID
: Wireless Network Name of TL-WR710N.
*
Wireless Password/PIN
: Pre-encryption password of
TL-WR710N.
*
LAN/WAN
: This port works as LAN in Access Point/Repeater/
Client/WISP Client Router mode and as WAN in Wireless Router
mode.
Reset
It is used to reset the Router to its factory defaults.
Indication
TL-WR710N LED:
Status
Solid Blue
The device is working properly.
Blinking
Condition 1: System is booting.
Condition 2: The Ethernet Cable or USB Device
is connecting to the product.
For more detailed information about
Reset
, please refer to
Appendix: Troubleshooting
.
Client Mode
TL-WR710N is used as a wireless network
card to connect the wireless network signal
or wireless router.
3 4
WISP Client Router Mode
In WISP mode, TL-WR710N enables multiple
users to share Internet connection from WISP.
5
For Windows 7
Click the icon at the bottom of your desktop.
Click refresh button, and then select the target
network. Click Connect.
3 4
Enter the Security key. Click OK.
For Mac OS
Click the icon at the right top of your
desktop. Click refresh button, and then select
the target network.
3 4
The screen will appear as shown below. Enter
the Password, and then click OK.
LAN
: This port works as LAN in Wireless Router/Access
Point/Repeater/Client/WISP Client Router mode .
USB
It is used to connect USB Flash or Hard Disk for le sharing and
Mobile devices for charging.
Repeater Mode
TL-WR710N is used to extend the range of
wireless signal of the existing AP or wireless
router.
The LAN devices share the same IP from ISP
through Wireless or Wired port. While
connecting to Internet, the LAN/WAN
Ethernet port works as a WAN port at
Wireless Router mode. It’s suitable for most
hotel and home network with Plug-N-Play
after nishing Instant Wireless Connection.
In this mode, this device can be connected to a
wired network and transform the wired access
into wireless that multiple devices can share
together, especially for a home, oce or hotel
where only wired network is available.
In this mode, this device can copy and
reinforce the existing wireless signal to
extend the coverage, especially for a large
space to eliminate signal-blind corners.
In this mode, this device can be connected to
another device via Ethernet port and act as
an adapter to grant your wired devices
access to a wireless network, especially for a
Smart TV, Media Player, or game console only
with an Ethernet port.
In this mode, the device enables multiple
users to share Internet connection from
WISP. The LAN port devices share the same IP
from WISP through Wireless port.
Go to Start > Control Panel > View network
status and tasks > Change adapter settings.
Right click Wireless Network Connection,
and select Properties. Double click Internet
Protocol Version 4 (TCP/IPv4) in the item list.
1 2
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" mode on your PC. Click
OK.
Click the icon at the right top of your
desktop. Then click Open Network
Preferences…. The screen will appear as
shown below. Choose AirPort and click
Advanced….
2
Set the Congure IPv4 as “Using DHCP”. Click
OK.
1
Go to Metro interface> Control Panel > View
network status and tasks > Change adapter
settings. Right click Wireless Network
Connection,
and select Properties. Double
click Internet Protocol Version 4 (TCP/IPv4) in
the item list.
2
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" mode on your PC.
Click OK.
1
The default SSID of the network is TP-LINK_xxxxxx
(The TP-LINK_xxxxxx is the SSID on the label. )
The pre-encryption function is enabled by default and the default Network key/Security key is the Password on the
label. The password is case-sensitive.
1.
2.
5
When you can see Connected as shown in the
following screen, you’ve successfully
connected to the wireless network.
5
When Connected appears behind the SSID,
you have successfully connected to the target
network.
5
When appears before the SSID, you have
successfully connected to the target network.
(This method is for connecting to the default Wireless Router Mode. If you want to configure Wireless Router Mode or choose other modes, please skip to Router Conguration.)
S/N:XXXXXXXXXXXX
Model:TL-WR710N(EU) Ver:1.0
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
MAC:B0487A663D6C
IC: 8853A-WR710N
FCC ID: TE7WR710N
1PXFS
7
_
)["
.PEFM 5-
83/
%FGBVMU"DDFTT
IUUQUQMJOLMPHJOOFU
6TFSOBNFBENJO
1BTTXPSEBENJO
.CQT8JSFMFTT/.JOJ1PDLFU3PVUFS
Reset
LAN/WAN LAN
USB
Protected by
NAT Firewall
Wired Network
Cable
Wired Network
Cable
SSID: def
Connect the plug directly to the TL-WR710N to finish
hardware connection.
The provided power plug may differ from the picture due
to different regional power specifications. Here we take
the EU version as an example.
Note:
To Next Page
Need help?
General
Weight and Dimensions
