TurboChef NGO/SOTA - Page 83

APPENDIX - REPLA
CING OVEN C
OMPONENT
S
A
-10
Figure A-12: Outer Shell Removed - Control Panel
75
81
84
72
73
74
80
79
76
Figure
R
eference #
Item Description Item Part Number Hardware Description Hardware Part Number(s)
72 C
able, Display, Power, 3-Pin, 3-Wire
i1-9475 None None
73 Cable, Display, Ribbon, 26-Pin, 5” 100196 None None
74 Cable, Smart Card Reader 100182 None None
75 Control Board CON-7002 Screw, #6-32 x 3/8, Int Tooth, PPH, SS 102911 (qty 4)
76 Displa
y
, TFT
C
ON-7011
S
cr
ew, #6-32 x 3/8, Int Tooth, PPH, SS
102911 (qt
y 4)
77 Displa
y Bracket, Bottom
i1-9465 S
crew, #6-32 x 3/8, Int Tooth, PPH, SS
102911 (qt
y 2)
78 Display Bracket, Top i1-9464 Screw, #6-32 x 3/8, Int Tooth, PPH, SS 102911 (qty 2)
79 Housing, Control, Left End
i1-9057 (SOTA)
i1-9453 (SBK
)
S
cr
ew, #10-32 x 1.00, Skt Hd, SS
Nut, Keps, Hex, #10-32, Ext Tooth, Cres
P
in, Roll, 0.125 Dia x 1.00 Lg, SS
101800 (qt
y 2)
102963 (qty 2)
101133 (qt
y 2)
80 Housing
, Control, Display
i1-9058 (SO
T
A)
i1-9452 (SBK)
S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 4)
81 Keypad*
i1-9451-1 (SO
TA)
i1-9451-2 (SBK
)
None None
82 Ligh
t Ring, LED (SOTA only)
i1-9198 S
crew, #8-32 x 1/2, PPHD, Int Sems, SS
102923 (qt
y 2)
83 Medallion, Display
i1-9491 (SO
TA)
i1-9489 (SBK
)
Nut
, Push, 1/8”
S
cr
ew, #8-32 x 1/2, PPHD, Int Sems, SS
101293 (qt
y 4)
102923 (qt
y 2)
84 Smart Card Reader 100506 Screw, #6-32 x 3/8, Int Tooth, PPH, SS 102911 (qty 4)
85 T
r
im Bezel, Display*
i1-9454 Nut
, P
ush, 1/8”
101293 (qt
y 8)
86 T
r
im Ring, Logo (SOTA only)
i1-9455 Nut
, P
ush, 1/8”
101293 (qt
y 4)
77
78
85
82
83
86
To prevent interference with display,
do not apply push nut to this prong.
*
T
o prevent air bubbles when laying the keypad, start by sticking one end of the keypad to the surface and
then laying it acr
oss to
wards the other end. As you lay the keypad, ensure a proper seal.