TurboChef NGO/SOTA - Component Replacement: Outer Shell & Back Cover Required

APPENDIX - REPLACING OVEN COMPONENTS
A
-11
Figure
R
ef
erence #
Item Description Item Part Number Hardware Description
Hardware Part
Number(s)
87 Capacitor, High-Voltage (x2)
100216 (
Japan 50 Hz)
100207 (Japan 60 Hz)
100213 (Kor
ea)
100232 (All others)
Screw, #6-32 x 3/8, Int Tooth, PPH, SS
Nut, #6-32 Keps, Ext Tooth, SS
102911
102961
88 Capacitor Clamp (x2)
104197 (
Japan 50 Hz)
104126 (Japan 60 Hz)
100134 (
All others)
Screw, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl 101688 (qty 2)
89 Diode
, High-Voltage (x2)
100481 S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 2)
90 D
uct, Magnetron Cooling Fan, L*
i1-9479 S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 2)
91 D
uct, Magnetron Cooling Fan, R*
i1-9480 S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 2)
92 Jumper
, Capacitor (Intl 50 Hz only)
i5-9378 None None
93 Magnetron (x2) NGC-3015 Screw, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl 101688 (qty 4)
94 P
ower Cord
C
ontact factory
None None
95 T
erminal Block
102049 (1 Ph)
102043 (3 P
h)
S
crew, #10-32 x 3/4 Lg, PPH Sems, Int Tooth
102937 (qt
y 2)
96 T
hermostat, Magnetron, 270°F (x2)
104228 S
crew, Sh Mtl, Drill Point, 6-32 x 3/8, PPHD, Zinc
101684 (qt
y 2)
97 T
ransformer, Filament (x2)
NGC-3061-1 (USA
)
NGC-3061-2 (Intl)
NGC-3061-3 (Japan)
S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 4)
98 T
ransformer, High-Voltage (x2)
NGC-3062-1 (USA)
NGC-3062-2 (Intl)
NGC-3062-3 (Japan)
S
crew, #8 x 1/2, Serr Ph Truss Hd, Sheet Mtl
101688 (qt
y 4)
99
Wire Harness, Line Voltage
(not shown)
i1-9172 (1 Ph)
i1-9171 (3 Ph)
None None
100
W
ire Harness, Cooling Fans
(not shown)
i1-9174 None None
101
W
ir
e Harness, Heaters
(not shown)
i1-9239 None None
102
Wire Harness, Transformers
(not sho
wn)
i1-9173 None None
Replacing Items - Removing Outer
Shell and Back Cover Required
(Figure A-13)
DANGER: Before replacing any oven
component, ensur
e the oven is removed
from any power source. Replacing a
component while the o
ven is plugged
in can result in serious injury or death.
CA
UTION: Be careful to not tear the
insulation when servicing components.
Always r
einstall the insulation pr
operly
befor
e reinstalling the outer shell or
back co
v
er.
NO
TE: Hardware listed is required for
installing component to oven.
Figure A-13: Outer Shell and Back Cover Removed
89
97
98
94
88
87
96
93
* NOTE: Left and right orientation based on looking at the back of the oven.
90
91
95
92