Ugolini IT GL - Page 20

20
IT GL
ALARM CAUSE REMEDY LIGHT COVERS FLASHING
MEMORY ERROR LOADED DEFAULT
The memory of the machine is out of service and it is not pos- sible to load the settings saved before the last switching OFF. The machine will start to work with the default settings.
Disconnect the machine from electrical supply. Plug the unit again and turn it on. In case the message remains on even after these operations have been carried out, Service call is required.
YES
(for 10 seconds at start)
WRITE MEMORY ERROR
The memory of the machine is out service and it is not possi- ble to save the settings.
If the alarm remains on even after some time a Service Call is required.
YES
(for 10 seconds at start)
INSUFFICIENT VOLTAGE
The voltage is not enough to start the compressor. If the ma- chine is equipped with two compressors the second one is im- mediately stopped.
Check the connection to the power supply. If the alarm re- mains on even after some time a Service Call is required.
YES
CLOCK OUT OF SERVICE.SET TIME
The clock is out of service and the time is not correct. If the alarm remains on even after some time a Service Call
is required.
YES
(for 10 seconds at start)
LCD OUT OF SERVICE
The Liquid Crystals Display out of service. If the alarm remains on even after some time a Service Call
is required.
YES
(for 10 seconds at start)
OVERPRESSURE COMPRESSOR 1
Insufficient ventilation of the unit. The compressor(s) is imme- diately stopped.
In this case check that all around the dispenser there is suf- ficient space for ventilation, at least 15 cm (6") on each side and that condenser filter is free from dust or other obstruc- tions. In case the message remains on even after these opera- tions have been carried out, Service call is required.
YES
BOWL1: TOP COVER OPENED
The Top Cover of bowl 1/2/3 is open or not correctly closed. The corresponding mixers and refrigeration circuit are turned OFF. The bowl can't run.
Verify that the Top Cover is properly installed and that the electric contacts are clean.
NO
BOWL1:TEM.SENSOR OUT OF SERVICE
The Temperature Sensor of bowl 1/2/3 is out if service. The corresponding refrigeration circuit is turned OFF.
If the alarm remains on even after some time a Service Call is required.
YES
BOWL1:FIX SENSOR OUT OF SERVICE
The Fix Magnetic Field Sensor of bowl 1/2/3 is out if service. The corresponding refrigeration circuit is turned OFF.
If the alarm remains on even after some time a Service Call is required.
YES
BOWL1:ROT.SENSOR OUT OF SERVICE
The Rotating Magnetic Field Sensor of bowl 1/2/3 is out if ser- vice. The corresponding refrigeration circuit is turned OFF.
If the alarm remains on even after some time a Service Call is required.
YES
BOWL1: LOCKED MIXERS
The mixers of bowl 1/2/3 is locked due to excessive viscosity: see Mixers self-protection and Maximum viscosity self-set- ting. The corresponding refrigeration circuit is turned OFF. The mixers ON / OFF cycle is started.
Check the correct Brix level of the product and reduce the set viscosity.
YES
BOWL1: GEARMOTOR OUT OF SERVICE
The mixers gear motor of bowl 1/2/3 are out of service. If the alarm remains on even after some time a Service Call
is required.
YES
BOWL1: COOLING OUT OF SERVICE
The refrigerant circuit of bowl 1/2/3 is out of service. If the alarm remains on even after some time a Service Call
is required.
YES
000 BLACKOUT(S) M=00:00 T=00:00
One or more blackout(s) happened when the machine was working.
Check that the blackout was not long enough to compromi- se the quality of the food product contained in the bowls due to excessive temperature. In this case substitute the food product with new one.
NO
PERFORM MACHINE CLEANING
The Machine Cleaning Period expired and it is necessary to perform the cleaning of the machine.
Perform the Machine Cleaning procedure as described in this manual and delete the corresponding cleaning alarm from the Machine Setting Menu or pressing keys (L) and (F) together for one second.
YES
PERFORM CONDENSER CLEAN.
The Condenser Cleaning Period expired and it is necessary to perform the cleaning of the condenser filter.
Perform the Condenser Cleaning procedure as described in this manual and delete the corresponding cleaning alarm from the Machine Setting Menu or pressing keys (L) and (F) together for one second.
YES