Unipower Aspiro 1U - User Manual

Questions and Answers:

T
Teresa ArroyoSep 2, 2025
What should I do if Unipower Power Supply shows Battery Fuse Failure?
- T
  Thomas EllisSep 3, 2025
  If your Unipower Power Supply reports a Battery Fuse Failure, it's likely due to a tripped load breaker or a blown load fuse. Verify there is no short circuit in the load or battery cabling and ensure the breaker/fuse is correctly rated. Reset the breaker; if it trips again, there is a problem with the load, battery, or the breaker itself. Replace the breaker/fuse if necessary.
N
Nathan BrownSep 15, 2025
What does Urgent Module Failure mean on Unipower Power Supply?
- L
  Lisa HughesSep 15, 2025
  If your Unipower Power Supply shows 'Urgent Module Failure', it means more than one rectifier is reporting Module failure. Refer to the troubleshooting steps for a Module failure alarm.
J
Jordan MorganAug 31, 2025
How to resolve Communication Failure on Unipower Power Supply?
- J
  jmillsAug 31, 2025
  If your Unipower Power Supply is showing a Communication Failure, it could be due to a module failure, modules not installed in the correct position, or a broken/disconnected communication wire. Check the non-communicating address. If the rectifier address does not communicate, reinstall the module and wait for 5 minutes. Verify the communication cable is properly connected and not damaged; replace it if necessary. If the board address does not communicate, check if it is installed in the system; if it is, replace the board. If there is a non-communicating module or unit, remove the non-communicating address from the controller only if you are sure you do not use them anymore. Verify if the controller is operating properly; if not, replace it.
C
Chelsea HendersonSep 18, 2025
Why is my Unipower Power Supply showing Low Battery Temperature?
- M
  Michael WalkerSep 18, 2025
  If your Unipower Power Supply displays a 'Low Battery Temperature' warning, it means the battery temperature has dropped below the set Low battery temperature limit. Check the heating of the system and ensure the ambient temperature is not lower than the recommended battery temperature.
L
Lori RodriguezSep 18, 2025
How to troubleshoot Battery Fuse Failure on Unipower Aspiro 1U?
- T
  tcolonSep 18, 2025
  If your Unipower Power Supply shows a 'Battery Fuse Failure', it is likely caused by a tripped load breaker or a blown load fuse. Verify there is no short circuit in load or battery cabling and that the breaker/fuse is correctly rated. Reset the breaker; if it trips again, there's a problem with the load, battery, or the breaker itself. Replace the breaker/fuse if necessary.
K
kemprobertSep 23, 2025
How to turn off Alarms Blocked on Unipower Aspiro 1U?
- R
  Richard ClaySep 23, 2025
  To turn off Alarms Blocked on Unipower Power Supply, it needs to be manually turned OFF to allow the alarms to be displayed.
C
cgreenAug 28, 2025
How to troubleshoot AC Low Voltage on Unipower Power Supply?
- K
  Kimberly JonesAug 28, 2025
  If your Unipower Power Supply is experiencing an AC Low Voltage issue, it means the AC voltage has dropped below the set limit. Verify the Low AC voltage limit setting, the AC input connection, and the AC input voltage.
J
james97Aug 27, 2025
What causes High Load on Unipower Aspiro 1U?
- J
  Joseph JenkinsAug 27, 2025
  If you are experiencing a High Load issue with your Unipower Power Supply, it could be caused by a faulty module or the rectifier load current exceeding the set High load limit. Compare the load current with the installed rectifier capacity. You can add a rectifier, reduce the load, verify the High load limit setting, or replace the faulty module.
W
Whitney SmithAug 26, 2025
Why is my Unipower Aspiro 1U Power Supply showing High System Voltage?
- D
  Dennis Nelson Jr.Aug 26, 2025
  If your Unipower Power Supply is experiencing high system voltage, it could be due to a module failure or the system voltage exceeding the set limit. Replace the faulty module and check the High Voltage Alarm limit setting.
J
Jordan MillerAug 26, 2025
What to do if Unipower Aspiro 1U shows Mains Error?
- J
  Jason LongAug 26, 2025
  If your Unipower Power Supply shows a Mains Error, it means the AC supply is OFF on one rectifier in a system with only one plugged-in rectifier, or OFF on at least two rectifiers in a system with a minimum of two rectifiers plugged in. Make sure the AC input breaker is ON and verify the AC input connection.