Unitech EA630 Quick Start Guide

Installing the Battery and Battery Cover
Insert battery in the direction as shown in the picture below.
Checking LED Status
LED Description
Red Light
￭ Battery Charging
￭ Twinkling to indicate battery
low status(less than 15%)
Green Light
￭ Battery Fully charged
￭ Barcode scan good read
Blue Light Message
If scanner app is running, LED control by scanner app.
No LED (Red and Green) display when battery is out(even AC IN)
1. Unlock the battery cover by turning the knobs
a quarter of a turn (90°). Lift the battery cover up
to 45 degrees (45°), then gently pull the cover off.
2. Pull the battery up to remove it.
3. Lock the battery cover by turning the knobs
a quarter of a turn (90°). Make sure the battery cover
is securely closed, or you may be unable to turn on
the terminal.
5
For other product documentation, please scan the QR code below for more information.
WARNING! There is a risk of fire and burns if the battery is handled improperly. DO NOT
disassemble, crush, puncture, short external contacts, or dispose the battery
pack in fire or water. DO NOT attempt to open or service the battery. Dispose of
used batteries according to local recycling guidelines in your area.
CAUTION!
 To ensure the unit working properly, please keep all connectors
away from the contaminants staying inside of them such as dust, grease,
mud, and water. The negligence may cause the unit with no communication,
short circuited, overheated and so on.
 If the connector is damaged, please ensure the connector is being fully
repaired before using the unit to avoid causing short circuited.
http://www.ute.com/
Copyright 2020 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Charging the battery
Before using the terminal for the first time, you need to charge it for
about 24 hours. For the regular use, you can charge the terminal for
4 hours to recharge the battery to full capacity. To charge the terminal,
please use the USB charging cable or the cradle.
Connect the type C USB cable to the USB port on EA630 and the other
end of the USB cable connect to AC power adapter into the electrical
outlet on the USB plug. The charging LED indicator on EA630 is turning
red when it is in charging state.

Unitech EA630 Specifications

General

Screen shape	Flat
Display diagonal	6 \
Touchscreen type	Capacitive
Display resolution	2160 x 1080 pixels
Native aspect ratio	18:9
Gorilla Glass version	Gorilla Glass 6
Maximum display brightness (HDR)	450 cd/m²
Multimedia Messaging Service (MMS)	Multimedia Messaging Service (MMS) is a standard way to send messages that include multimedia content to and from a mobile phone over a cellular network
Form factor	Bar
Product color	Black
International Protection (IP) code	IP65
Processor cores	8
Processor model	636
Processor family	Qualcomm Snapdragon
Processor frequency	1.8 GHz
RAM capacity	3 GB
Compatible memory cards	MicroSD (TransFlash)
Maximum memory card size	256 GB
Internal storage capacity	32 GB
Platform	Android
App distribution platform	Google Play
Operating system installed	Android 10.0
Speakers	Mono
Rear camera type	Single camera
Front camera type	No
Rear camera resolution (numeric)	16 MP
Front camera resolution (numeric)	- MP
Talk time (3G)	- h
Battery voltage	3.85 V
Battery capacity	4000 mAh
Certification	FCC, NCC, BSMI, VCCI, CCC, RCM, CEC, BQB, N-Mark
Sustainability certificates	CE, RoHS
Storage temperature (T-T)	-30 - 70 °C
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Cables included	USB Type-C
4G standard	LTE-TDD & LTE-FDD
3G standards	WCDMA
SIM card type	NanoSIM
Wi-Fi standards	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Bluetooth version	5.0
SIM card capability	Dual SIM
Security algorithms	WEP, WPA, WPA2
Mobile network generation	4G
Subscription type	No subscription
USB version	3.2 Gen 1 (3.1 Gen 1)
Harmonized System (HS) code	85171300

Weight and Dimensions

Depth	13.9 mm
Width	76.4 mm
Height	157 mm
Weight	230 g