To Next PageTo Next PageWhy does my VEVOR SSX130 Ice Maker stop 3 minutes after turning on?
Your VEVOR Ice Maker might be stopping shortly after being turned on due to high voltage protection. This could be triggered by a high-temperature environment, a dirty condenser filter, or a damaged fan motor.
Why VEVOR SSX130 only makes one tray of ice per cycle?
If your VEVOR Ice Maker only makes one tray of ice each time it's turned on, the issue might be related to the ice full sensor or ice tray baffle. Check if the ice tray baffle can open and close automatically and whether the ice full switch is falling correctly.
Why is my VEVOR SSX130 Ice Maker making ice so slowly?
Several factors could be causing your VEVOR Ice Maker to produce ice slowly. The condenser might be dirty, so clean it. The ambient temperature might be too high, or ventilation may be poor; ensure the temperature doesn't exceed 40 ? and that there's adequate ventilation. Also, the float ball in the tank could be too high or leaking; adjust it or replace the tank. Other potential issues include water tank leakage (replace the tank), a faulty inlet valve (clean or replace it), or insufficient space around the machine (provide adequate space).
What to do if the ice from my VEVOR SSX130 is too thin?
If the ice from your VEVOR Ice Maker is too thin or incomplete, it could be due to several reasons. Check the tank water level for any leakage. Also, inspect the inlet valve to ensure it is working correctly. Insufficient water pressure could also be the cause; ensure the water pressure is at 0.13 - 0.55Mpa. Finally, check the water pipes for blockages and dirt.
What to do if ice won't fall off the tray in my VEVOR SSX130 Ice Maker?
If the ice isn't falling off the ice tray in your VEVOR Ice Maker, several factors could be responsible. First, the ice tray might be dirty, requiring cleaning and disinfection. Second, the machine might not be placed on level ground; adjust it accordingly. Third, the environment temperature might be too low; it should be higher than 5 ?. Fourth, the solenoid valve could be faulty and need replacement.
What to do if the 'ice full' light is on but my VEVOR SSX130 Ice Maker is empty?
If the 'ice full' indicator light is on but your VEVOR Ice Maker is empty, the ice tray baffle might be faulty. Check if the ice tray baffle is stuck.
What does E1, E2 Alarm mean on a VEVOR SSX130?
If your VEVOR Ice Maker displays an 'E1, E2 Alarm', it indicates that both the ambient temperature sensor and the return air temperature sensor are broken. Replace both sensors and ensure the unit has enough space around it.
What does E1 Alarm mean on a VEVOR Ice Maker?
If your VEVOR Ice Maker displays an 'E1 Alarm', it means the ambient temperature sensor is broken and needs to be replaced.
What does E2 Alarm mean on a VEVOR SSX130?
If your VEVOR Ice Maker displays an 'E2 Alarm', it indicates that the return air temperature sensor is broken and needs replacement.
General| Model | SSX130 |
|---|---|
| Voltage | 115V |
| Frequency | 60Hz |
| Refrigerant | R290 |
| Material | Stainless Steel |
| Color | Silver |
| Ice Production Capacity | 130 lbs/24H (60 kg/24H) |
| Ice Making Cycle | 11-20 minutes |
| Type | Commercial Ice Maker |
| Ice Shape | Cube |
Explains prohibition, warning, fire hazard, and high voltage danger symbols and their meanings.
Covers compressor settling, placement, water exposure, flammable materials, installation, disassembly, and grounding safety.
Addresses electrical safety, component handling, flammable materials, ventilation, and proper disposal.
Details on electrical system safety, child supervision, handling malfunctions, and warnings about gas leaks.
Details proper grounding, socket use, installation standards, and environmental conditions for operation.
