Specifications:
•
Processor
•
1.0GHz NXP i.MX 6QuadPlus (or i.MX 6Quad) Cortex-A9
quad-core SoC
•
System Memory
•
1GB DDR3 SDRAM onboard
•
Storage
•
4GB eMMC Flash memory
•
Boot Load
•
4MB SPI Flash ROM
•
Graphics
•
Support three integrated, independent 3D/2D and video
graphics processing units
•
Supports OpenGL
®
ES 3.0, OpenCL and OpenVG
™
1.1 hardware
acceleration
•
Supports MPEG-2, VCI and H.264 video decoding up to 1080p
•
Supports SD encoding
•
LAN
•
Micrel KSZ9031RNX Gigabit Ethernet transceiver with
RGMII support
•
Audio
•
NXP SGTL5000 low power stereo codec
•
HDMI
•
Integrated HDMI Transmitter
•
USB
•
SMSC USB2514 USB 2.0 High Speed 4-port hub controller
•
Expansion I/O
•
1 x miniPCIe slot
Powered by a 1.0GHz NXP i.MX 6QuadPlus Cortex-A9 ARM SoC with
enhanced graphics and memory performance or a 1.0GHz NXP i.MX 6Quad
Cortex-A9 SoC, the VAB-820 provides the perfect blend of high performance
and low power consumption to meet the high end demands of advanced
industrial, energy management and in-vehicle applications.
VAB-820
Key Features:
• Compact 10cm x 7.2cm Pico-ITX form factor
• 1.0GHz NXP i.MX 6QuadPlus (or i.MX 6Quad)
Cortex-A9 quad-core SoC
• Flawless HD video performance up to 1080p
• Wide operating temperature range, -20°C~70°C
• Fanless and ultra low power consumption
• Linux and Android solution packs available
Quick Guide
Box Contents
Note:
Please ensure that all items in the box are present before using this product.
If any of the items are missing or damaged, contact your distributor or sales
representative immediately.
•
1 x
VAB-820 mainboard
•
1 x DC power cable
•
1 x Audio cable
•
1 x USB cable
•
1 x Console cable (3-wired for debugging the console)
Layout Diagram
2
1
4
3
1.01-11072016-172500
•
Onboard I/O
•
1 x COM connector with power supply (supports 8-wire
DTE mode)
•
1 x COM/CAN connector with power supply (supports one
RS-232 (TX/RX) and two FlexCAN TX/RX ports)
•
1 x RTC battery connector
•
1 x MIPI CSI-2 connector (supports two data lanes)
•
1 x SPI master connector (supports two SPI slave devices)
•
1 x S-Video input pin header
•
1 x Front audio pin header for Line-in, Line-out and Mic-in
•
1 x Boot flash select jumper (for SPI or micro SD)
•
1 x USB 2.0 and USB 2.0 OTG pin header
•
1 x Miscellaneous pin header (for one I²C pair, DIO (4 GPI +
4 GPO), system reset button and LEDs for power/WPAN/
Wi-Fi/WWAN
•
1 x Dual-channel, 18/24-bit LVDS panel connector
•
1 x LVDS Inverter connector
•
1 x LVDS power select jumper
•
1 x DC-in connector (12V)
•
1 x miniPCIe slot (supports multiple connections and buses
including JTAG)
•
2 x PoE pin headers (support optional PD power board)
•
Front Panel I/O
•
1 x Micro SD Card slot
•
Back Panel I/O
•
1 x HDMI port
•
2 x USB 2.0 ports
•
1 x Gigabit Ethernet port (supports optional IEEE802.3at type 2)
•
1 x Composite input RCA jack
•
Watchdog Timer
•
Integrated watchdog timer supports two comparison points.
Each comparison point can interrupt ARM core, and a second
comparison point capable of generating external interrupts on
WDOG line
•
Power Supply
•
12V DC-in
•
Operating Temperature
•
-20°C ~ 70°C (3G and Wi-Fi not included)
•
Operating Humidity
•
0% ~ 95% (non-condensing)
•
Form Factor
•
Pico-ITX
•
10cm x 7.2cm (100mm x 72mm)
•
Operating System
•
Android 6.0 and Android 5.0
•
Linux Kernel 4.1.15 and Linux Kernel 3.14.28
•
Compliance
•
CE, FCC
Note:
For the software evaluation, please visit VIA website:
http://www.viatech.com
To Next Page
