The VIVOTEK AP-FHP-0105-R/AP-FHP-0100-R/AP-FHP-0105-T Hyper PoE Extender is a versatile device designed to extend Power over Ethernet (PoE) and data transmission distances, offering flexible deployment options for network devices. This quick installation guide outlines its functionality, usage, and important considerations for optimal performance.
Function Description
The Hyper PoE Extender serves as an intermediary device that allows for the extension of both power and data over standard Ethernet cables, specifically CAT5e or CAT6 UTP/STP. It is particularly useful in scenarios where network devices, such as IP cameras or access points, need to be deployed beyond the typical 100-meter limit of Ethernet cabling, without the need for additional power outlets. The extender comes in different models to suit various power input and output requirements:
- AP-FHP-0105-R (DC in Rx Module): This model acts as a receiver (Rx) for DC power input and features a Hyper Port for extended PoE and data transmission, along with a Fast Ethernet (FE) RJ45 port and a DC Jack. It is designed to receive power from a DC source, such as a 56V adapter, and then forward both power and data over the Hyper Port.
- AP-FHP-0105-T (DC in Tx Module): This model functions as a transmitter (Tx) for DC power input. Similar to the Rx module, it includes a Hyper Port, an FE RJ45 port, and a DC Jack. It is intended to take DC power and data, combine them, and transmit them over the Hyper Port to a connected device or another extender.
- AP-FHP-0100-R (PoE in Rx Module): This model is a receiver (Rx) that accepts PoE input. It features a Hyper Port and an FE RJ45 port. This variant is ideal for receiving PoE directly from a PoE injector or switch and then extending that power and data.
The core function of these extenders is to regenerate and amplify the Ethernet signal and power, allowing for significantly longer cable runs than traditional Ethernet. This is achieved through the "Hyper Port," which is optimized for extended-range power and data delivery. The devices operate within a wide temperature range, ensuring reliability in various environmental conditions.
Usage Features
The Hyper PoE Extender is designed for straightforward installation and integration into existing network infrastructures. Key usage features include:
- Extended Reach: The primary benefit is the ability to extend the distance of PoE and data transmission. This is crucial for large installations where devices are located far from the main network switch or power source. The distance capabilities vary depending on the cable quality and power requirements of the connected devices, with the manual providing a detailed distance/power chart for reference.
- Flexible Power Input: Depending on the model, the extender can accept either DC power from an adapter (AP-FHP-0105-R/T) or PoE directly from a PoE injector/switch (AP-FHP-0100-R). The AP-FHP-0105-R model specifically includes a 56VDC/65W power adapter in its package for convenience.
- Simple Connection Diagram: The guide illustrates clear connection diagrams for various setups. For instance, an AP-FHP-0100-R can connect to a 95W PoE injector, then to an AP-FHP-0105-R, which in turn connects to a network switch. Similarly, an AP-FHP-0105-T can connect to a 56V adapter, then to an IP camera, with the Hyper PoE port facilitating the extended connection.
- LED Indicators: The devices are equipped with LED indicators to provide real-time status updates:
- PoE LED (Yellow ON): Indicates that the PoE port is connected to a Powered Device (PD).
- LAN LED (Green ON): Shows that data is being transmitted or received on the LAN port.
- LAN LED (OFF): Signifies no connection on the LAN port.
- PWR LED (Yellow ON): Confirms that the power adapter is connected to the Hyper PoE Extender.
- LINK LED (Green ON): Indicates that the Rx and Tx Hyper PoE Extenders are linked.
These LEDs are invaluable for quick troubleshooting and verifying proper operation.
- DIP Switch for PoE Control (AP-FHP-0105-T only): The AP-FHP-0105-T model features a DIP switch to control the PoE output. This allows users to enable or disable PoE delivery to the connected PD device. This is an important safety feature, especially when connecting to non-PD devices or PoE switches, to prevent potential damage. Users are explicitly warned to switch PoE to "Off" if connecting to a PoE switch or non-PD device.
- Grounding Capability: The devices include a ground screw, emphasizing the importance of proper grounding for stable and safe operation. The manual recommends ensuring the grounding resistance is lower than 0.5Ω.
- Pin Assignment Information: The guide provides the Hyper PoE Link Cat.5e/6 pin assignment (5-8 Pin V+ and 1-4 Pin V-), which can be useful for advanced users or for verifying cable integrity.
- Cable Quality Importance: The guide stresses the critical role of cable quality, advising the use of CAT5e or CAT6 UTP/STP cables and cautioning against low-quality cables, which can severely limit cabling distance and power delivery. This highlights a key factor in achieving the advertised performance.
Maintenance Features
While the Hyper PoE Extender is designed for robust and reliable operation with minimal direct maintenance, certain aspects contribute to its long-term performance and ease of upkeep:
- Durable Design: The devices are built to operate within a specified temperature range, suggesting a design intended for durability in various environments.
- Troubleshooting via LEDs: The comprehensive LED indicators serve as a primary maintenance tool, allowing users to quickly diagnose connection, power, and data transmission issues without specialized equipment. A glance at the LEDs can confirm if power is supplied, if data is flowing, and if the extenders are linked.
- Cable Management Best Practices: The emphasis on using high-quality CAT5e or CAT6 cables and avoiding low-quality alternatives is a maintenance recommendation in itself. Proper cable selection and management prevent signal degradation and power loss over time, reducing the need for future troubleshooting or component replacement.
- Grounding for Stability: The inclusion of a grounding screw and the recommendation for low grounding resistance contribute to the device's stability and protection against electrical interference or surges, which can prolong its lifespan and reduce the likelihood of failures.
- Clear Installation Guide: The "Quick Installation Guide" itself acts as a maintenance aid, providing clear instructions for initial setup and ongoing reference. Understanding the correct connection procedures and power requirements helps prevent misconfigurations that could lead to device malfunction or premature wear.
- No Moving Parts: As a solid-state electronic device, the extender typically has no moving parts, which inherently reduces the need for mechanical maintenance.
- Environmental Considerations: The operating temperature range (-20°C to 60°C) indicates that the device is designed to withstand a range of environmental conditions, minimizing the impact of temperature fluctuations on its performance and longevity.
In summary, the VIVOTEK Hyper PoE Extender is a practical solution for extending network reach and power delivery, characterized by its ease of use, clear status indicators, and robust design considerations that contribute to reliable and long-lasting operation.
To Next Page
Need help?
General
