Vogelzang International VG5790 User Manual (English)

Other manuals for Vogelzang International VG5790

Questions and Answers:

Z
Zachary WhiteAug 21, 2025
Why does my Vogelzang International Pellet stove display flashing E1?
- R
  Robert CruzAug 21, 2025
  The 'E1' error code on your Vogelzang International Pellet stove indicates a potential issue. This can be due to several reasons: * The convection blower is overheating, which means you should clean any dust off the windings and fan blade. If oiling the blower doesn't solve the problem, the blower itself may be faulty. * Operating the stove on the highest setting for too long can cause overheating. Try using a lower heat setting. * Using fuel other than wood pellets can cause this error. Make sure you are only using approved wood pellets. * A power surge or voltage drop could trip the high limit switch. Using a surge protector can help. * The high limit switch itself might be malfunctioning and need replacement.
K
Kathleen JohnsonAug 26, 2025
How to fix smoke smell coming back into the home from Vogelzang International VG5790 Pellet stove?
- W
  William GravesAug 27, 2025
  If you're experiencing a smoke smell coming back into your home from your Vogelzang International Pellet stove, consider the following: * Inspect all vent pipe connections for leaks. Seal them with RTV silicone (rated 500°F or higher) and UL-181-AP foil tape. Ensure the square to round adapter piece on the combustion blower is properly sealed with the same RTV. * Check the combustion blower gaskets for damage and replace them if necessary.
M
Mark AlvarezAug 30, 2025
Why does the convection blower on my Vogelzang International VG5790 Pellet stove shut off and come back on?
- K
  Kathy HahnAug 30, 2025
  If the convection blower on your Vogelzang International Pellet stove is shutting off and then restarting, here are a couple of potential causes: * The convection blower might be overheating and tripping its internal temperature shutoff. Try cleaning any dust off the windings and fan blades. If cleaning doesn't help, the blower may be faulty. * There could be a circuit board malfunction. Test the current going to the convection blower. If power is still being sent to the blower when it shuts off, the control board is fine. If power is not being sent, the control board is likely bad.
M
Michael SmithSep 2, 2025
Why does the high limit switch keep tripping on my Vogelzang International VG5790?
- C
  Courtney LaneSep 3, 2025
  If the high limit switch on your Vogelzang International Pellet stove keeps tripping, here are some possible reasons: * The convection blower may be overheating. Clean any dust off the windings and fan blades. If oiling the blower doesn't help, the blower may need to be replaced. * The stove may be running on the highest setting for extended periods. Try using a lower heat setting. * Using fuel other than wood pellets can cause this. Make sure you are only using approved wood pellets. * A power surge or brownout can cause the switch to trip. Use a surge protector. * The high limit switch itself may be malfunctioning. If the other items check out OK, consider replacing the switch.
K
Karla HarrisSep 4, 2025
What does flashing E5 mean on my Vogelzang International Pellet stove?
- S
  Stephen McdonaldSep 4, 2025
  The T-stat sensor may have come unplugged from the control board. Check to see if the sensor is unplugged. If the sensor is not unplugged, then the sensor is damaged or has a short, and it will need to be replaced.
K
Kenneth HortonSep 5, 2025
Why does my Vogelzang International Stove high limit switch keep tripping?
- M
  meltonsamanthaSep 5, 2025
  The high limit switch in your Vogelzang International Stove might be tripping due to several reasons: * The convection blower could be overheating. Try cleaning any dust off the windings and fan blades. If cleaning doesn't resolve the issue, the blower itself may be faulty. * Operating the stove on the highest heat setting for extended periods can cause overheating. Consider using a lower heat setting. * Using fuel other than wood pellets can lead to this issue. Ensure you're only using approved wood pellets. * A power surge or brownout could be the cause; using a surge protector might help. * The high limit switch itself may be malfunctioning and require replacement.
L
Leah RodriguezSep 7, 2025
What to do if my Vogelzang International Stove display is flashing “E1”?
- I
  imayerSep 7, 2025
  If the display on your Vogelzang International Stove is flashing “E1”, it indicates a problem that needs attention. The potential causes and solutions are: * The convection blower may be overheating. Clean any dust from the windings and fan blade. If oiling the blower does not help, the blower may be faulty. * The stove might be overheating because it's been left on the highest setting for too long. Try operating it at a lower heat setting. * Using fuel other than wood pellets can cause this issue. Check for signs of unapproved fuel and stop using it immediately. * A power surge could be the problem. Try using a surge protector. * The high limit switch may be malfunctioning. If other solutions don't work, consider replacing it.
R
Ralph BurkeSep 13, 2025
Why does my Vogelzang International Stove convection blower shut off and come back on?
- M
  Margaret MccoySep 13, 2025
  The convection blower in your Vogelzang International Stove might be shutting off and on due to: * Overheating, which causes the internal temperature shutoff to trip. Clean any dust off of the windings and fan blades. If cleaning the blower does not help, the blower may be bad. * A circuit board malfunction. Test the current going to the convection blower. If there is power being sent to the blower when it is shut off, then the control board is fine. If there is NOT power being sent to the blower when it shuts off during operation, then you have a bad control board.
T
Teresa WatkinsSep 14, 2025
Why does smoke smell come back into the home from my Vogelzang International Stove?
- S
  Sean MillsSep 14, 2025
  If you're experiencing a smoke smell coming back into your home from your Vogelzang International Stove, consider these potential causes: * There may be a leak in the vent pipe system. Inspect all vent pipe connections and seal them with RTV silicone rated for 500°F or higher, and UL-181-AP foil tape. Also, ensure the square to round adapter piece on the combustion blower is properly sealed with the same RTV. * The gasket on the combustion blower might have deteriorated. Inspect both gaskets on the combustion blower and replace them if damaged.