EasyManua.ls Logo

Votronic VAC 1215 M 3A - User Manual

Votronic VAC 1215 M 3A
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Mounting Instructions and Operating Manual for
Fully Automatic Battery Chargers:
Automatic Charger VAC 1215 M 3A Charging Capacity 12 V / 15 A No. 0404
Automatic Charger VAC 1220 M 3A Charging Capacity 12 V / 20 A No. 0406
Automatic Charger VAC 1225 M 3A Charging Capacity 12 V / 25 A No. 0408
Automatic Charger VAC 1230 M 3A Charging Capacity 12 V / 30 A No. 0410
Please read the mounting instructions and the operating manual including the safety
instructions. Particularly observe page 15 "Safety Regulations and Appropriate Application",
prior to starting connection and start-up.
Fully automatic battery charger with 3 charging ports for special purpose vehicles, ambulance cars,
intervention vehicles and fire-fighting vehicles.
VOTRONIC chargers of series "VAC - M" distinguish by their compact design, low weight (high-frequency switching power
supply, Switch Mode Technology), as well as full charging capacity - even in the event of large fluctuations in the power
supply (undervoltage/overvoltage, sine wave form, frequency).
The intelligent microprocessor charging control with charging programs "IU1oU2oU3" (constant current - constant voltage)
and dynamic charging time calculation ensures automatic, quick and gentle full charging, as well as subsequent 100 %
trickle charge of the connected batteries from any charging state. At the same time, simultaneous supply of 12 V consumer
loads, which are connected in parallel, is ensured or charging of very large batteries (depending on case of application).
Charging Ports and Charging Programs:
1. Main Battery I (Master), full charging capacity:
Charging programs 1) - 4) for batteries in lead technology "DIN Lead Acid / AGM 1" - "Engine" - "AGM 2" - "Gel"
Charging programs 5) - 8) for batteries in LiFePO4 technology "13.9 V" - "14.2 V" - "14.2 V" - "14.6 V"
Automatic lithium trickle charging 9) of the LiFePO4 battery when the vehicle is stopped (seasonal operation) to
maintain a charging state of 50-80 %, which is advantageous for the battery lifetime. Simultaneous floating of 12 V
consumer loads, such as alarm systems, WLAN etc., as well as the vehicle's starter battery, see page 5.
2. Main Battery II, full charging capacity, with built-in charging current distributor:
a) Battery type "II = I". Parallel charging II with the same charging programs as battery I 1) 8), see table 2.
b) Starter battery "II < I". The charging program II is designed for the vehicle starter battery for quick starting ability
and trickle charging by additional components, particularly in case of very high consumer current rates.
3. Signalling/Charging Port "III":
Signalling port 12 V for vehicle engine immobilizer, mains display or as separate auxiliary port 12 V / 2 A, 3 A, usable for
support charging and trickle charging of a (lead) vehicle starter battery with overcharge protection, see page 4.
Further Characteristics of the Unit:
The charging voltage is free from peaks and is controlled in such a way, that overcharging of the batteries is excluded.
Fully Automatic Continuous Operation: The charger may be connected continuously to the battery, thus keeping the
full charge. Battery discharge in case of power failure is avoided (separation by safety relay).
Maintenance Lithium LiFePO4, Auto Wake Up, Maintenance Phase: Regular, automatic activation of the battery cell
equalization charging (balancing) every 10 days to ensure continuous full charge of the battery.
Battery regeneration in case of extended standstill periods: twice a week to avoid harmful acid accumulation.
Parallel and Floating Operation: In case of simultaneous consumption, the battery will either continue to be charged or
maintained via trickle charging. Calculation and control of the adaptation of the charging times is effected automatically
by the charger.
Unattended Charging: Multiple protection against overload, overheating, overvoltage, short circuit, reverse battery,
incorrect behaviour and back discharge of the battery by electronically controlled gradual reduction down to complete
separation of charger and battery by integrated safety relays.
Question and Answer IconNeed help?

Do you have a question about the Votronic VAC 1215 M 3A and is the answer not in the manual?

Summary

VOTRONIC Automatic Charger: Manual Overview

Charging Ports and Programs Explained

Details the charger's ports and their respective charging programs for various battery types.

Installation and Initial Setup Guide

Unit Installation and Mounting Requirements

Provides instructions for installing the battery charger unit in a suitable location, considering ventilation and protection.

Battery Connection and Start-up Procedures

Guides users through connecting batteries and performing the initial start-up of the charger.

Wiring Diagram and Battery Type Settings

12 V Connection Plan with Options

Illustrates the wiring connections for the 12V system, including optional configurations.

Optional Ports and Temperature Sensor Use

Temperature Sensor for Battery Protection

Details the crucial role of the temperature sensor for LiFePO4 and lead-acid battery protection.

Unit Settings and Lead Battery Charging

LiFePO4 Battery Charging Programs

Setting Main Battery II Charging

Detailed Charging Process Sequence

Chronological Charging Cycle Stages

Describes the step-by-step process of a complete main battery charging cycle.

Technical Specifications Overview

Technical Data and Charger Ratings

Presents detailed technical specifications, ratings, and data for the charger models.

Safety Regulations and Proper Application

Safety Guidelines and Usage Restrictions

Outlines critical safety regulations, warnings, and appropriate application for the charger.

Votronic VAC 1215 M 3A Specifications

General IconGeneral
Output Voltage12V DC
Output Current15A
Charging Current3 A
Charging MethodIUoU
Protection Featuresshort circuit

Related product manuals