ToneLab EasyStart
R
R
e
e
s
s
t
t
o
o
r
r
i
i
n
n
g
g
t
t
h
h
e
e
F
F
a
a
c
c
t
t
o
o
r
r
y
y
P
P
r
r
e
e
s
s
e
e
t
t
P
P
r
r
o
o
g
g
r
r
a
a
m
m
s
s
:
:
1. While holding down the, Up, Down and EXIT buttons, press the STANDBY button to turn on the power. The
bank display indicates “P” and the 1-4 LED buttons will blink. The name display will indicate, “RELOAD? Now
release the three buttons.
2. If you’re sure you want to restore the factory data, press the WRITE button - the display will indicate
“LOADING”, and will indicate “COMPLETE” when restoring is finished. The ToneLab SE will automatically be
switched to Program Select Mode.
3. If you decide you don’t want to do this, simply press the EXIT button
S
S
e
e
l
l
e
e
c
c
t
t
i
i
n
n
g
g
a
a
n
n
d
d
l
l
i
i
s
s
t
t
e
e
n
n
i
i
n
n
g
g
t
t
o
o
T
T
o
o
n
n
e
e
L
L
a
a
b
b
’
’
s
s
3
3
2
2
P
P
r
r
e
e
s
s
e
e
t
t
P
P
r
r
o
o
g
g
r
r
a
a
m
m
s
s
:
:
ToneLab has 96 program locations in 24 banks, with 4 programs in each bank (24x4=96).
Programs in banks 1-8 are identical to programs in banks 9-16 and 17-24.
1. Use the BANK UP and BANK DOWN switches to select a bank.
2. Use the Channel Select switches 1-4 to select a channel in that bank.
3. Once you find a program (sound) that you like, you can use the knobs and selectors of the Pedal, Amp,
Cabinet, and Effects section to easily tweak the sound.
4. To turn ON an effect that is OFF in the program, simply press the TYPE button for the effect you wish to add.
When the LED is lit turn the knob to your effect of choice, the effect will be on. Then use the knobs below
and follow the top panel chart to edit the sound.
5. To turn OFF an effect, press the Type button.
6. Press the FX ON/OFF (TUNER) switch to go to FX ON/OFF mode. This mode lets you switch each effect
ON/OFF just like if you were using separate stomp pedals. Program switches 1-4 turn ON/OFF Pedal,
Modulation, Delay, and Reverb effects, and the BANK DOWN switch will turn ON/OFF the Insert effect. You
can plug in your own favorite pedal to the Insert Send/Return jacks on the back panel of the ToneLab SE.
The effect is on when the LED is lit.
7. By pressing the A /Bch switch you can instantly switch between the amp model and cabinet model that are
specified for A and B of each program.
8. The two Expression pedals are assigned to control the most appropriate parameters for each program, such
as wah, volume, delay, reverb input level, or other effect parameters.
9. The Control switch allows you to instantly turn on/off pedal settings, tap tempo the delay time etc. Press the
CONTROL button to make it blink, and use Value knob1 to select the effect you want to control.
CONTROL switch EFFECT ON/OFF:
• “I/ON OFF” External Insert effect on/off
• “P/ON OFF” Pedal effect on/off
• “A/ON OFF” Amp model on/off
• “C/ON OFF” Cabinet effect on/off
• “M/ON OFF” Modulation effect on/off
• “D/ON OFF” Delay effect on/off
• “R/ON OFF” Reverb effect on/off
Note: The CONTROL button LED indicates the on/off status.
2
To Next Page
Loading...
Need help?
General
