WAGNER Super Finish 23i - English

29
Super Finish 23i
CONTENTS
Contents
1 SAFETY REGULATIONS FOR AIRLESS SPRAYING 30
1.1 Flash point _________________________________ 30
1.2 Explosion protection _________________________ 30
1.3 Danger of explosion and re from sources of
ignition during spraying work _________________ 30
1.4 Danger of injury from the spray jet _____________ 30
1.5 Secure spray gun against unintended operation __ 30
1.6 Recoil of spray gun __________________________ 30
1.7 Breathing equipment as protection against
solvent vapors ______________________________ 30
1.8 Prevention of occupational illnesses ____________ 30
1.9 Max. operating pressure ______________________ 31
1.10 High-pressure hose _________________________ 31
1.11 Electrostatic charging
(formation of sparks or ames) ________________ 31
1.12 Use of units on building sites and workshops _____ 31
1.13 Ventilation when spraying in rooms ____________ 31
1.14 Suction installations _________________________ 31
1.15 Earthing of the object ________________________ 31
1.16 Cleaning the unit with solvents ________________ 31
1.17 Cleaning the unit ___________________________ 31
1.18 Work or repairs at the electrical equipment ______ 31
1.19 Work at electrical components _________________ 32
1.20 Setup on an uneven surface ___________________ 32
2 GENERAL VIEW OF APPLICATION ____________ 32
2.1 Application ________________________________ 32
2.2 Coating material ____________________________ 32
2.2.1 Coating materials with sharp-edged additional
materials __________________________________ 32
2.2.2 Filtering (for spay work) ______________________ 32
3. DESCRIPTION OF UNIT _____________________ 33
3.1 Functioning of the unit _______________________ 33
3.2 Explanatory diagram _________________________ 34
3.3 Technical data ______________________________ 35
4 STARTUP _________________________________ 35
4.1 Gun ______________________________________ 35
4.2 High pressure hose and pressure gauge _________ 36
4.3 Hopper____________________________________ 36
4.4 Connection to the mains network ______________ 37
4.5 Cleaning preserving agent when starting-up of
operation initially ___________________________ 37
4.6 Ventilate unit (hydraulic system) if the sound of
inlet valve is not audible ______________________ 37
4.7 Taking the unit into operation with
coating material ____________________________ 37
5 TRANSPORTATION _________________________ 38
6 HANDLING THE HIGHPRESSURE HOSE _______ 38
7 INTERRUPTION OF WORK ___________________ 38
8 CLEANING THE UNIT _______________________ 39
8.1 Cleaning the unit from the outside _____________ 39
8.2 Suction lter _______________________________ 39
8.3 Cleaning the Airless spray gun _________________ 40
9 SERVICING ________________________________ 40
9.1 General servicing ___________________________ 40
9.2 High-pressure hose __________________________ 40
10 REPAIRS AT THE UNIT ______________________ 41
10.1 Inlet valve Pusher ___________________________ 41
10.2 Inlet valve _________________________________ 41
10.3 Outlet valve ________________________________ 42
10.4 Pressure control valve ________________________ 42
10.5 Replacing the power cable ___________________ 43
10.6 Typical wear parts ___________________________ 43
10.7 Connection diagram _________________________ 44
10.8 Remedy in case of faults ______________________ 45
11 SPARE PARTS AND ACCESSORIES ____________ 46
11.1 Super Finish 23i accessories ___________________ 46
11.2 Spare parts list Super Finish 23i ________________ 48
11.3 Spare parts List Trolley _______________________ 50
11.4 Spare parts list hopper 5l _____________________ 50
Testing of the unit ________________________________ 51
Important information on product liability_____________ 51
Note on disposal __________________________________ 51
Guarantee declaration _____________________________ 51
CE - declaration__________________________________ 105
European service network _________________________ 108