321 4 5
6
8 9
7 10 11
TRIMMING WITH ATTACHMENT COMBS
Your trimmer includes three trimming attachments; stubble, medium and
long. The stubble guide has 1 bar, the medium-cut attachment has two
bars and the long-cut attachment has three bars.
These attachments are ideal for blending, tapering and
defining beards, as well as for achieving a “close trim”
stubble look around the face. To use the attachments,
go with the hair direction. To achieve closer looks, go
against the hair direction.
TRIMMING NOSE HAIR
Make sure the nasal passages are clean. Slowly move Rotary Head in
and out of each nostril, no more than 1/4-inch deep. Keep the side of the
cutting head firmly against the skin to prevent a tickling sensation. (The
Detail Head may also be used.)
TRIMMING EAR HAIR
Make sure the outer areas of the ears do not contain any wax. Hold the ear
flat with one hand and carefully insert Rotary Head no more than 1/4-inch
into the outer ear.
CAUTION: Do not insert the Rotary Head or any other foreign object
into the inner ear. For hair growing on the outside of the ear, simply move
the Rotary Head slowly along the edges of the ear. (The Detail Head may
also be used.)
TRIMMING EYEBROWS
Slowly move detailer to neatly trim stray hairs. For precise, even trimming,
slowly move the detailer closer or farther away from eyebrows to achieve
desired length.
INSTALLATION/ REMOVAL OF TRIMMING HEADS
Make sure trimmer unit is turned “OFF”.
1 Turn trimmer head counterclockwise and
lift off.
2 Place trimmer head on trimmer and turn
trimmer head clockwise to lock on.
TRIMMING AND EDGING
YOUR BEARD
The following are suggested trimming steps and trimmer positions. You
may find different procedures work better for you.
1. Comb your beard in the direction that it grows to help reveal stray hairs
that may be longer than the others.
2. Attach the guide comb to trim and taper your
beard. With the blades pointing toward you, begin
with the 5-position guide set at a long trimming
length. For best results, start at each sideburn and
stroke downward toward your neck. Trim toward
your chin in smooth, overlapping strokes, following the lay of your beard. If
you trim against the way your beard naturally lays, the trimmer will cut the
hair much shorter and the result may be patchy. Adjust the guide comb to
progressively shorter settings until you reach the desired length of beard.
You may wish to set the guide comb to cut closer near the ear and down
under the chin, changing to a longer setting toward the front of the face and
point of your chin. Always be sure the guide is snapped solidly into the
desired position before you start to trim.
3. Remove the 5-position guide and cut the outline of your beard. Starting
under your chin and working back toward your jawbone and ears, cut the
outer perimeter of your beard underneath the jawbone. Continue the line all
the way up to the ears and hairline.
4. Accentuate your beard line by using the trimmer in a downward motion.
Start at the line you’ve created and, working from the chin back toward the
ears, trim the area right under your beard line.
5. Define the upper part of your beard using the same technique.
6. For a neater finished look, use the guide comb on position 2. Then,
using the trimmer in an upward motion, start trimming under the chin with
short, outward, rolling strokes. Continue trimming until entire jawline is
blended.
TRIMMING YOUR MUSTACHE
1. Comb your mustache.
2. Hold the trimmer in a vertical position with the blades pointing toward
you in order to define the line of your mustache.
3. With the guide set at a fairly long trimming length, begin trimming your
mustache, starting at the top and working down to your upper lip. Use
progressively closer settings to get the look and length you desire.
4. For tapering the mustache, set the guide comb at a medium length.
Starting in the middle of your mustache, follow the lip line and taper with
short upward strokes of the trimmer, working out toward the corners until a
gentle shape is created on the bottom of your mustache.
5. As a finishing step, remove the guide and, using only the bare blades,
make a definitive line at the bottom of your mustache.
DETAILING SIDEBURNS, MUSTACHES & BEARDS
using trimmer head.
Slowly move trimmer across desired areas to neatly trim and shape.
TRIMMING ARM & LEG HAIR using trimmer head.
Simply glide the trimmer over your arm or leg until desired hair length is
achieved. The first time you trim the hair, start by using a longer setting on
the guide comb on the trimmer, then use progressively shorter settings if a
shorter length is preferred.
TRIMMING CHEST & STOMACH HAIR with trimmer
head.
Glide the trimmer over your torso region, in an upward motion until desired
hair length is achieved. The first time you trim the hair, start by using a
longer setting on the 5-position guide comb on the trimmer, then use
progressively shorter settings if a shorter length is preferred.
For the cleanest look, simply attach the shaver
head.The shaver makes for the perfect tool to clean up,
in, and around your beard, mustache, or other facial hair.
Shave against hair growth while stretching the skin. After
every use, remove the shaver foil by pressing the button
on the shaver head and carefully using cleaning brush
provided.
On/Off
Switch
Trimming
Head
1/16” Guide
1/8” Guide
3/16” Guide
Cleaning
Brush
Blade
Oil
1/16” 1/8” 3/16”
SERVICE, REPAIR & GUARANTEE
We guarantee this Wahl product against mechanical defects for
the time period indicated on the clipper package (if used on the
voltage and cycle indicated on the appliance). Damage due to
rough handling or dropping is not covered by this guarantee.
Batteries and broken blades are not covered by this guarantee.
If your Wahl product requires service, do not return it to the store
where purchased. Call Wahl (toll free) at 1-866-787-WAHL (9245)
for the name and address of the Wahl Service Centre closest
to you or send it prepaid with a note explaining the problem to
the address below. Products under guarantee will be returned
postage prepaid.
Wahl Canada Inc.
165 Riviera Drive
Markham, Ontario, L3R 5J6
For service and repair information, please refer to our website:
www.wahlglobal.com/canada
Detail
Head
Ear/Nose
Head
Shaving
Head
Mustache
Comb
SPECIAL FEATURES:
Your trimmer has been designed with several advanced features to help
you get perfect results every time you trim. Your trimmer may be used
to touch-up around ears, nose and eyebrows, neatly detail goatees,
beards, mustaches, neckline, sideburns, or anywhere you may need
grooming.
The trimmer you
purchased may not
have all of these heads.
5-Position
Guide
IMPORTANT SAFEGUARDS
When using your electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS AND SAFEGUARDS
BEFORE USING THIS TRIMMER.
DANGER
To reduce the risk of death or injury by
electric shock:
1. Do not reach for an appliance that has fallen
into water. Unplug immediately from the outlet.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall
or be pulled into a tub or sink. Do not place in or
drop into water or other liquid.
4. Except when charging, always unplug this
appliance from the electrical outlet immediately
after using.
5. Always unplug this appliance before cleaning.
6. Unplug the charger before using trimmer.
WARNING
To reduce the risk of burns, electrical shock or
injury to persons:
1. Do Not Crush, Disassemble, Heat Above
100°C (212°F), or Incinerate the appliance, due
to Risk of Fire, Explosion, or Burns.
10. Do not use this appliance with a damaged or
broken blade or trimming attachment, as facial
injury may occur.
11. Always attach plug to appliance first, then to
outlet.
12. Use only the charger supplied by the
manufacturer to recharge.
13. During use, do not place or leave the
appliance where it is expected to be subject to
damage by an animal, or exposed to weather.
To disconnect, turn unit “OFF - 0,”
then remove plug from outlet.
SAVE THESE INSTRUCTIONS
For Household Use Only
RECHARGING
1. This trimmer is conveniently designed for household use. It
should be allowed to charge overnight before first use.
2. Remove the trimmer, recharging transformer and accessories
from the packing material.
3. Connect the transformer to the trimmer. BE SURE TRIMMER IS
IN THE “OFF - 0” POSITION WHEN CHARGING.
4. Plug the recharging transformer into any convenient electrical
outlet at the correct voltage.
5. When trimmer is low in power, it should be connected to the
transformer and plugged into an outlet to assure maximum
power is available when it is next used. This transformer
is designed to continuously charge the battery without
overcharging.
6. Ni-Cad battery life may be extended with the following
procedure: Once every month, let the trimmer run until the
motor stops. Move the switch to the “OFF - 0” position and
recharge fully overnight.
2. This power unit is intended to be correctly
orientated in a vertical or floor mount position.
3. This appliance can be used by children aged
from 14 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction, by a person
responsible for their safety, concerning the use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
4. Use this appliance only for its intended use as
described in this manual. Do not use attachments
not recommended by the manufacturer.
5. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or if
it has been dropped into water.
6. Keep the cord away from heated surfaces.
7. Insert only recharging transformer plug
supplied by the manufacturer into charger
receptacle.
8. Do not use outdoors or operate where aerosol
(spray) products are being used or where oxygen
is being administered.
9. Never drop or insert any object into any
opening.
CLEANING/STORAGE
Before storing your trimmer, use the cleaning brush to whisk any loose
hairs from the unit and the blades. Store unit in such a manner so that
blades are protected from damage.
When the trimmer is not in use, the trimmer guide/blade guard
attachment should be in place to protect the blades.
TROUBLESHOOTING
If your Trimmer does not seem to take a charge, check the following
before returning it for repair:
1. Check outlet current by plugging in another appliance.
2. Make sure the outlet simply is not connected to a light switch which
turns the power at the outlet off when lights are turned off.
3. Be sure the trimmer is properly connected to the recharging
transformer, all connections are secure and the switch on the
trimmer is turned “OFF - 0.”
4. If your electricity is connected to a master power switch, we
suggest the trimmer be disconnected from the charger anytime the
master switch is off. Leaving the unit plugged into a dead outlet or
an unplugged charger will drain the battery.
5. If trimmer does not run and it is completely charged, turn the unit
“ON - I” and pinch or push the blades manually. (Oil may have dried
out between the blades, so they may be temporarily stuck together.)
CARING FOR YOUR TRIMMER
OILING BLADES
For best results, put one or two drops of Wahl Clipper Oil on the blades
only when necessary, or approximately once a month. Motor bearings
are permanently lubricated—do not attempt to oil.
When oiling your trimmer, turn the trimmer “ON - I,” hold the unit with
the blades facing DOWN and squeeze one or two drops of oil onto the
blades. Wipe off excess oil with soft cloth.
NOTICE—DO NOT OVER OIL!
Excessive oiling or application of liquids will cause damage if allowed to
seep back into motor.
BLADE CARE
Trimmer blades have precision-hardened, ground and lapped cutting
teeth. Blades should be handled carefully and never bumped or used to
cut dirty or abrasive material.
Should blades become damaged or dull, you may purchase a new blade
assembly from Wahl.
RECYCLE/REPLACEMENT
OF NI-CAD BATTERY
Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc), or rechargeable (Ni-Cad, Ni-MH, etc.) batteries.
Under normal use, the rechargeable nickel-cadmium batteries in your
trimmer may last up to five years. At the end of their life, when they
will no longer take a full charge, the nickel-cadmium batteries must
be removed and recycled or disposed of properly. Do not attempt to
replace the batteries. All servicing or battery replacement should be
performed by an Authorized WAHL Service Location. To remove the
batteries for recycling or disposal, follow these steps:
1. Unplug transformer from outlet, disconnect cord
from trimmer and allow the batteries to
completely run down before
disassembly.
2. Remove
any attached
trimming
heads.
3. Pry the trimmer
housing apart.
CONTAINS SEALED, RECHARGEABLE NICKEL-
CADMIUM BATTERY. MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
The RBRC Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery
contained in this product indicates Wahl is voluntarily participating in an
industry program to collect and recycle these batteries at the end of their useful
life, when taken out of service in the United States or Canada. The RBRC
program provides a convenient alternative to placing used Ni-Cd batteries into
the trash or the municipal waste stream, which is illegal in some areas. Please
call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area.
Wahl’s involvement in this program is part of our commitment to preserving
our environment and conserving our natural resources.
Operating Instructions
All In One
Part / Partie 73905
©2016 Wahl Clipper Corp.
Printed in China
To Next Page
Need help?
General
