Wald BICYCLE BASKET User Manual

LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
BICYCLE BASKET
with handle & mounting holder
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
ASSEMBLY INSTRUCTIONS
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
Mfgr.No.3133 GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
Mfgr.No.3133GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
ASSEMBLY INSTRUCTIONS
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
BICYCLE BASKET
with handle & mounting holder
Mfgr.No.3133GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
ASSEMBLY INSTRUCTIONS
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
BICYCLE BASKET
with handle & mounting holder
A
WALD LLC MAYSVILLE, KY.
DRN
TITLE
APVD
SCALE
DATE
NO.
REVISIONS
ZONE
REV
DESCRIPTION
BY
DATE
CHAD
3133GB BASKET -
ASSEMBLY INSTRUCTIONS
1:1
9-15-03
C-68019
A
B
C
D
E
F
A
B
C
D
E
F
1
2
3 4 5 6
1
2 3 4 5
6
A
CHAD
4-8-09
REVISED WARNING NOTE - S.V.P.

Wald BICYCLE BASKET Specifications

General

Brand	Wald
Model	BICYCLE BASKET
Category	Bicycle Accessories
Language	English

Summary

Bicycle Basket with Handle and Mounting Holder

Assembly Instructions

Loosely Assemble Brace

Assemble brace onto holder wires with short screws, angled upward.

Center and Hang Holder Brackets

Position holder brackets over handlebar and loosely attach handlebar clamps.

Attach Basket to Holder

Connect basket to holder, ensuring lock end and handle engage correctly.

Adjust Holder Brace

Vertically position holder brace on side wires for proper basket placement.

Remove Basket from Holder

Lift basket by raising handle upright and pulling away from holder.

Secure Fittings

Tighten all holder fittings to ensure a secure assembly.