Water Right Impression Series - User Manual

Water Right Impression Series

32 pages

To Next Page

To Next Page

Loading...

Impression Series

®

Impression RC Series

Metered Water Softeners

For Models:

• IM-844 • IMP-844

• IM-948 • IMP-948

• IM-1044 • IMP-1044

• IM-1054 • IMP-1054

• IM-1248 • IMP-1248

• IM-1354 • IMP-1354

• IMC-835 • IMPC-835

• IMC-1035 • IMPC-1035

• IMRC-1054 • IMPRC-1054

• IMRC-1354 • IMPRC-1354

Table of Contents

Questions and Answers

A
Amy MillerAug 30, 2025
How to fix excessive water in the regenerant tank of my Water Right Water Filtration System?
- J
  Jared TaylorAug 30, 2025
  Excessive water in the regenerant tank can be caused by several factors: * Improper program settings: Check the refill setting. * Plugged injector: Remove the injector and clean or replace it. * Drive cap assembly not tightened properly: Retighten the drive cap assembly. * Damaged seal/stack assembly: Replace the seal/stack. * Restricted or kinked drain line: Check the drain line for restrictions or debris, and unkink the drain line. * Plugged backwash flow controller: Remove the backwash flow controller and clean or replace it. * Missing refill flow controller: Replace the refill flow controller.
J
Jordan SwansonAug 29, 2025
What to do if my Water Right Water Filtration System control valve regenerates at the wrong time of day?
- S
  scott75Aug 30, 2025
  If your control valve regenerates at the wrong time, it could be due to: * A power outage: reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * Incorrect time of day setting: reset to the correct time of day. * Regeneration time set incorrectly: reset the regeneration time. * Control valve set at “on 0” (immediate regeneration): check the programming setting and reset to NORMAL (for a delayed regen time). * Control valve set at “NORMAL + on 0” (delayed and/or immediate): check the programming setting and reset to NORMAL (for a delayed regen time).
A
Antonio EllisAug 28, 2025
Why does the time of day flash on my Water Right Impression?
- N
  Nichole RoblesAug 28, 2025
  If the time of day is flashing on and off on your Water Right Water Dispenser, it could be due to: * **Power Outage:** Reset the time of day. If the PC board has battery back up present the battery may be depleted. See the front cover and drive assembly drawing for instructions. * **Drive Gear/Cap:** A broken drive gear or drive cap assembly. Replace the drive gear or drive cap assembly. * **Piston Rod:** A broken piston rod. Replace the piston rod. * **PC Board:** A defective PC board.
K
Kimberly JacksonSep 12, 2025
What to do if Water Right Impression control valve fails to draw in regenerant?
- M
  Martha BarnesSep 12, 2025
  If the control valve on your Water Right Water Dispenser fails to draw in regenerant, consider these possible causes: * The injector may be plugged: Remove and replace the injector. * The regenerant piston may be faulty: Replace the regenerant piston. * There may be a leak in the regenerant line connection: Inspect the regenerant line for air leaks. * The drain line may have a restriction or debris causing excess back pressure: Inspect the drain line and remove any restrictions. * The drain line may be too long or too high: Shorten the length and/or height. * The water pressure may be low: Check the incoming water pressure, ensuring it remains at a minimum of 25 psi.
Q
qcowanSep 15, 2025
What to do if my Water Right Water Dispenser control valve does not regenerate automatically?
- S
  Shannon ParsonsSep 15, 2025
  If your control valve isn't regenerating automatically, but does when you press and hold the correct buttons, consider these potential causes: * The bypass valve might be in the bypass position. * The meter might not be connected to the PC board. * The meter turbine could be restricted or stalled. * There might be incorrect programming. * The meter wire may not be securely installed. * The meter or PC board could be defective. Check the bypass valve position, meter connection, turbine, programming, and wiring. Replace any defective components as needed.
B
Brandon WoodsSep 22, 2025
Why Water Right Water Dispenser PC board does not display correct time?
- J
  Joshua HoustonSep 22, 2025
  If the PC board isn't displaying the correct time, it could be due to: * The power adapter being plugged into an outlet controlled by a light switch. * A tripped breaker switch and/or tripped GFI. * A power outage. * A defective PC board. Use an uninterrupted outlet, reset the breaker switch and/or GFI switch, and reset the time of day. If the PC board has a battery backup, the battery may be depleted.
N
Nicholas RobertsNov 24, 2025
Why is there excessive water in the regenerant tank of my Water Right Water Dispenser?
- N
  Nathan YatesNov 24, 2025
  If you notice excessive water in the regenerant tank of your Water Right Water Dispenser, here are a few things to investigate: * **Program Settings:** Review the refill setting to ensure it is properly configured. * **Injector:** Check the injector for any blockages. Remove and clean or replace if necessary. * **Drive Cap Assembly:** Make sure the drive cap assembly is properly tightened. * **Seal/Stack Assembly:** Inspect the seal/stack assembly for damage and replace if needed. * **Drain Line:** Examine the drain line for any restrictions, kinks, or debris. Clear any obstructions or unkink the line. * **Backwash Flow Controller:** Remove the backwash flow controller and clean or replace it if it's plugged. * **Refill Flow Controller:** Ensure the refill flow controller is...
A
Angela Ferguson DDSAug 27, 2025
How to reduce regenerant usage in my Water Right Water Dispenser?
- E
  Edward DoyleAug 27, 2025
  To address excessive regenerant usage in your Water Right Water Dispenser, consider the following: * **Refill Setting:** Check the refill setting to ensure it is correct. * **Program Settings:** Review the program settings to ensure they are specific to your water quality and application needs. * **Frequent Regeneration:** Check for leaking fixtures that may be exhausting the system's capacity, or consider if the system is undersized for your needs.
J
Justin BoyerAug 26, 2025
What should I do if my Water Right Water Dispenser display doesn't show water flowing?
- A
  Amber SchneiderAug 27, 2025
  If the display on your Water Right Water Dispenser doesn't indicate that water is flowing, check the following: * **Bypass Valve:** Ensure the bypass valve is not in the bypass position. Turn the bypass handles to place it in the service position. * **Meter Connection:** Verify the meter is connected to the meter connection on the PC board. * **Meter Turbine:** Check for any restrictions or stalls in the meter turbine. Remove the meter and inspect for rotation or foreign material. * **Meter Wire:** Make sure the meter wire is securely installed in the three-pin connector labeled METER. * **Meter:** The meter itself may be defective and need replacement. * **PC Board:** The PC board could be defective and need replacement.
T
teresa87Aug 26, 2025
Why my Water Right Impression doesn't automatically regenerate?
- B
  Brandon JordanAug 26, 2025
  If your Water Right Water Dispenser control valve doesn't regenerate automatically but does when you press and hold the correct buttons, consider these potential causes: * **Bypass Valve:** Ensure the bypass valve is in the service position. * **Meter Connection:** Check that the meter is connected to the meter connection on the PC board. * **Meter Turbine:** Inspect the meter turbine for any restrictions or stalls. Remove the meter to check for rotation or foreign material. * **Programming:** Verify that the programming is correct. * **Meter Wire:** Make sure the meter wire is securely installed into the three-pin connector labeled METER. * **Meter:** The meter might be defective and need replacement. * **PC Board:** The PC board could be defective and require replacement.

Water Right Impression Series Specifications

General

Brand	Water Right
Model	Impression Series
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

Installer Setup and Homeowner Guidance

Key steps for installers and homeowner reading requirements before operation.

Bypass Valve Operation

Understanding Bypass Valve Positions

Explanation of normal, bypass, diagnostic, and shut-off valve positions and their functions.

Installation Guidelines

Installation Warnings and Site Requirements

Safety warnings, plumbing material recommendations, and site requirement details.

Installation Procedures

Grounding and Drain Line Setup

Instructions for electrical grounding and proper drain line installation, including air gaps.

System Connections

Brine Tank and Overflow Line Setup

Details for connecting the brine tank safety float valve and overflow line to a drain.

Programming Procedures

Setting Time, Day, and Regeneration Parameters

Guide to setting the time of day, water hardness, day override, and regeneration time.

Startup Instructions

System Flushing, Conditioning, and Sanitizing

Procedures for flushing debris, conditioning media, and sanitizing the unit after installation.

Operating Displays and Maintenance

Understanding Unit Displays and Manual Regeneration

Explains system displays, regeneration modes, and how to initiate manual regeneration.

System Monitoring and Maintenance

Power Loss, Errors, Brine Tank Care

Covers battery replacement, error messages, brine tank salt maintenance, and RC unit information.

Troubleshooting Guide

Display and Regeneration Issues

Addresses common problems like no display, incorrect time, no water flow, and regeneration timing.

Troubleshooting

Water Quality and Regenerant Draw Problems

Solves issues related to hard water delivery and problems with drawing regenerant from the tank.

Troubleshooting

Error Codes and Motor Function Issues

Details error codes related to motor movement, stalling, and drain line problems.

Troubleshooting

Motor Timing and Valve Configuration Errors

Addresses errors for motor timing, stalling, and incorrect valve configurations.

Troubleshooting

Motor State, Leak, and Memory Errors

Covers errors for invalid motor states, leak detection, and memory-related issues.

Replacement Parts - Drive Assembly

Front Cover and Drive Components

Lists parts for the front cover, motor, PC board, and drive gears with part numbers.

Replacement Parts - Piston Assembly

Piston and Control Valve Body Components

Details parts for the piston assembly, O-rings, and control valve body with part numbers.

Replacement Parts - Valves and Fittings

Bypass Valve and Brine Elbow Components

Lists components for the bypass valve, brine elbow, and check valve assemblies.

Replacement Parts - Injectors & Meter

Injector Assemblies and Water Meter Components

Details injector assemblies and water meter and meter plug components.

Replacement Parts - Drain Line

Drain Line Assembly Components

Lists parts for drain line assemblies, including DLFCs for 3/4" and 1" sizes.

Replacement Parts - Brine Tank

Brine Tank and Safety Float Components

Details brine tank parts, safety float assemblies, and brine well components.

Replacement Parts - Cabinet

Cabinet and Brine Tank Shell Components

Lists parts for the top and bottom cabinet assemblies and brine well.

Installation Fitting Assemblies

PVC and Brass Sweat Fitting Assemblies

Details various PVC and brass sweat fittings for installation, including NPT and sweat types.

Installation Fitting Assemblies

Shark Bite and John Guest Fitting Assemblies

Lists Shark Bite and John Guest elbow fitting assemblies for installation.

Specifications and Usage Data

Model Specifications and Cycle Times

Provides detailed specifications for Impression/IMC models and cycle times for regeneration.

Water Softener Limited Warranty

Warranty Terms and Coverage Details

Outlines the warranty periods, exclusions, and claims process for the water softener.

Quick Reference Guide

Core Operations and Setting Summary

Summarizes general operation, setting time, manual regeneration, and bypass valve procedures.

Related product manuals

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression RC Series

Water Right Impression RC Series

Preview: Impression Plus Series

Impression Plus Series

Preview: Water Right IMP-844

Water Right IMP-844

Water Right IMP-948

Water Right IMP-1044

Water Right IMP-1054

Water Right IMP-1248

Water Right IMP-1354

Water Right IMP-1035

Water Right IMPC-1035

Water Right IM-1044