Water Right Impression Series - User Manual

Water Right Impression Series

32 pages

To Next Page

To Next Page

Loading...

Impression Series

®

Impression RC Series

Metered Water Softeners

For Models:

• IM-844 • IMP-844

• IM-948 • IMP-948

• IM-1044 • IMP-1044

• IM-1054 • IMP-1054

• IM-1248 • IMP-1248

• IM-1354 • IMP-1354

• IMC-835 • IMPC-835

• IMC-1035 • IMPC-1035

• IMRC-1054 • IMPRC-1054

• IMRC-1354 • IMPRC-1354

Table of Contents

Questions and Answers

C
christopherwebsterAug 25, 2025
How to fix no display on my Water Right Water Dispenser PC board?
- P
  ppowellAug 25, 2025
  If there's no display on the PC board of your Water Right Water Dispenser, here's what you can check: * **Power Outlet:** Ensure the dispenser is plugged into a working electrical outlet. If the outlet is faulty, repair it or try a different one. * **Power Adapter Connection:** Verify the control valve power adapter is securely plugged into the outlet and properly connected to the PC board. * **Power Supply:** Confirm the correct voltage is being supplied to the PC board. * **Power Adapter:** A defective power adapter can cause this issue, consider replacing it. * **PC Board:** If none of the above steps work, the PC board itself might be defective and need replacement. * **Battery:** Check the battery. Refer to the Operating Display and Maintenance section for instructions.
J
Jennifer FranklinSep 3, 2025
Why does the time of day flash on and off on my Water Right Water Filtration System?
- U
  unealSep 3, 2025
  The time of day flashing on and off typically indicates a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See the front cover and drive assembly drawing for instructions.
J
James MartinSep 3, 2025
What to do if my Water Right Water Filtration System control valve does not regenerate automatically when the button is depressed and held?
- T
  tylerpetersSep 3, 2025
  If the control valve doesn't regenerate automatically even when the correct button(s) is depressed and held, it could be due to: * A broken drive gear or drive cap assembly: Replace the drive gear or drive cap assembly. * A broken piston rod: Replace the piston rod. * A defective PC board: The PC board is defective.
A
Amy SheaSep 3, 2025
Why doesn't the display on my Water Right Water Filtration System indicate water is flowing?
- C
  Courtney HarrisonSep 3, 2025
  If the display doesn't indicate water is flowing, it could be due to: * The bypass valve being in the bypass position: Turn the bypass handles to place the bypass in the service position. * The meter not being connected to the meter connection on the PC board: Connect the meter to the three-pin connection labeled METER on the PC board. * A restricted/stalled meter turbine: Remove the meter and check for rotation or foreign material. * The meter wire not being installed securely into the three-pin connector: Verify the meter cable wires are installed securely into the three-pin connector labeled METER. * A defective meter: Replace the meter. * A defective PC board: Replace the PC board.
V
Vicki BrooksSep 4, 2025
How to troubleshoot no display on Water Right Water Filtration Systems?
- L
  Lisa FinleySep 4, 2025
  If your Water Right Water Filtration System displays no image on the PC board, it could be due to several reasons: * There's no power at the electrical outlet. Solution: Repair the outlet or use a working one. * The control valve power adapter isn't plugged in. Solution: Plug the power adapter into the outlet, or connect the power cord to the PC board connection. * There's an improper power supply. Solution: Verify the correct voltage is being supplied to the PC board. * The power adapter is defective. Solution: Replace the power adapter. * The PC board itself is defective. Solution: Replace the PC board.
R
Richard GentrySep 6, 2025
Why Water Right Water Filtration Systems control valve fails to draw in regenerant?
- R
  Ruben EdwardsSep 6, 2025
  If your Water Right Water Filtration System's control valve fails to draw in regenerant, it could be due to: * A plugged injector. Solution: Remove the injector and clean or replace it. * A faulty regenerant piston. Solution: Replace the regenerant piston. * A regenerant line connection leak. Solution: Inspect the regenerant line for an air leak. * A drain line restriction or debris causing excess back pressure. Solution: Inspect the drain line and clean it to correct the restriction. * A drain line that's too long or too high. Solution: Shorten the length and/or height. * Low water pressure. Solution: Check the incoming water pressure – it must remain at a minimum of 25 psi.
A
Allen WilliamsSep 6, 2025
Why does Water Right Water Filtration Systems control valve uses too much regenerant?
- S
  sbellSep 6, 2025
  If your Water Right Water Filtration System's control valve uses too much regenerant, consider the following: * Improper refill setting. Solution: Check the refill setting. * Improper program settings. Solution: Check the program settings to ensure they are specific to the water quality and application needs. * The control valve regenerates frequently. Solution: Check for leaking fixtures that may be exhausting capacity, or the system may be undersized.
J
Jeremy MurraySep 6, 2025
Why is there excessive water in the regenerant tank of my Water Right Water Filtration Systems?
- D
  Dustin OrtegaSep 6, 2025
  If you observe excessive water in the regenerant tank of your Water Right Water Filtration System, it might be due to: * Improper program settings. Solution: Check the refill setting. * A plugged injector. Solution: Remove the injector and clean or replace it. * The drive cap assembly not being tightened properly. Solution: Retighten the drive cap assembly. * A damaged seal/stack assembly. Solution: Replace the seal/stack. * A restricted or kinked drain line. Solution: Check the drain line for restrictions or debris and/or unkink the drain line. * A plugged backwash flow controller. Solution: Remove the backwash flow controller and clean or replace it. * A missing refill flow controller. Solution: Replace the refill flow controller.
G
Gabriela HendersonSep 7, 2025
Why does time of day flashes on and off on Water Right Water Filtration Systems?
- M
  Megan SmithSep 7, 2025
  If the time of day flashes on and off on your Water Right Water Filtration System, it is due to: a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions.
B
Beth ThomasSep 7, 2025
Why is Water Right Water Filtration Systems running water to drain?
- C
  Christine WilliamsSep 7, 2025
  If your Water Right Water Filtration System is running water to the drain, it could be due to: * A power outage during regeneration. Solution: Upon power being restored, the control will finish the remaining regeneration time. Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A damaged seal/stack assembly. Solution: Replace the seal/stack assembly. * Piston assembly failure. Solution: Replace the piston assembly. * The drive cap assembly not tightened properly. Solution: Retighten the drive cap assembly.

Water Right Impression Series Specifications

General

Brand	Water Right
Model	Impression Series
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

Installer Setup and Homeowner Guidance

Key steps for installers and homeowner reading requirements before operation.

Bypass Valve Operation

Understanding Bypass Valve Positions

Explanation of normal, bypass, diagnostic, and shut-off valve positions and their functions.

Installation Guidelines

Installation Warnings and Site Requirements

Safety warnings, plumbing material recommendations, and site requirement details.

Installation Procedures

Grounding and Drain Line Setup

Instructions for electrical grounding and proper drain line installation, including air gaps.

System Connections

Brine Tank and Overflow Line Setup

Details for connecting the brine tank safety float valve and overflow line to a drain.

Programming Procedures

Setting Time, Day, and Regeneration Parameters

Guide to setting the time of day, water hardness, day override, and regeneration time.

Startup Instructions

System Flushing, Conditioning, and Sanitizing

Procedures for flushing debris, conditioning media, and sanitizing the unit after installation.

Operating Displays and Maintenance

Understanding Unit Displays and Manual Regeneration

Explains system displays, regeneration modes, and how to initiate manual regeneration.

System Monitoring and Maintenance

Power Loss, Errors, Brine Tank Care

Covers battery replacement, error messages, brine tank salt maintenance, and RC unit information.

Troubleshooting Guide

Display and Regeneration Issues

Addresses common problems like no display, incorrect time, no water flow, and regeneration timing.

Troubleshooting

Water Quality and Regenerant Draw Problems

Solves issues related to hard water delivery and problems with drawing regenerant from the tank.

Troubleshooting

Error Codes and Motor Function Issues

Details error codes related to motor movement, stalling, and drain line problems.

Troubleshooting

Motor Timing and Valve Configuration Errors

Addresses errors for motor timing, stalling, and incorrect valve configurations.

Troubleshooting

Motor State, Leak, and Memory Errors

Covers errors for invalid motor states, leak detection, and memory-related issues.

Replacement Parts - Drive Assembly

Front Cover and Drive Components

Lists parts for the front cover, motor, PC board, and drive gears with part numbers.

Replacement Parts - Piston Assembly

Piston and Control Valve Body Components

Details parts for the piston assembly, O-rings, and control valve body with part numbers.

Replacement Parts - Valves and Fittings

Bypass Valve and Brine Elbow Components

Lists components for the bypass valve, brine elbow, and check valve assemblies.

Replacement Parts - Injectors & Meter

Injector Assemblies and Water Meter Components

Details injector assemblies and water meter and meter plug components.

Replacement Parts - Drain Line

Drain Line Assembly Components

Lists parts for drain line assemblies, including DLFCs for 3/4" and 1" sizes.

Replacement Parts - Brine Tank

Brine Tank and Safety Float Components

Details brine tank parts, safety float assemblies, and brine well components.

Replacement Parts - Cabinet

Cabinet and Brine Tank Shell Components

Lists parts for the top and bottom cabinet assemblies and brine well.

Installation Fitting Assemblies

PVC and Brass Sweat Fitting Assemblies

Details various PVC and brass sweat fittings for installation, including NPT and sweat types.

Installation Fitting Assemblies

Shark Bite and John Guest Fitting Assemblies

Lists Shark Bite and John Guest elbow fitting assemblies for installation.

Specifications and Usage Data

Model Specifications and Cycle Times

Provides detailed specifications for Impression/IMC models and cycle times for regeneration.

Water Softener Limited Warranty

Warranty Terms and Coverage Details

Outlines the warranty periods, exclusions, and claims process for the water softener.

Quick Reference Guide

Core Operations and Setting Summary

Summarizes general operation, setting time, manual regeneration, and bypass valve procedures.

Related product manuals

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression RC Series

Water Right Impression RC Series

Preview: Impression Plus Series

Impression Plus Series

Preview: Water Right IMP-844

Water Right IMP-844

Water Right IMP-948

Water Right IMP-1044

Water Right IMP-1054

Water Right IMP-1248

Water Right IMP-1354

Water Right IMP-1035

Water Right IMPC-1035

Water Right IM-1044