Watlow ez-zone pm - Output 1, 3 Mechanical Relay, Form C; Output 1, 3 Switched DC;Open Collector; Output 1, 3 Universal Process

Watlow EZ-ZONE
®
PM Integrated Controller • 26 • Chapter 2 Install and Wire
Warning:
Óç
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or pe-
ripheral devices. Failure to do so may
result in damage to equipment and
property, and/or injury or loss of life.
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm
2
(30 to 12 AWG)
single-wire termination or two 1.31
mm
2
(16 AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
Note:
To prevent damage to the control-
ler, do not connect wires to unused
terminals.
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent ground
loops.
Note:
The control output common terminal
and the digital common terminal are
referenced to different voltages and
must remain isolated.
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Warning:
ç
Explosion Hazard – Substitution of
component may impair suitability for
CLASS I, DIVISION 2.
Warning:
ç
Explosion Hazard - Do not disconnect
while the circuit is live or unless the
area is known to be free of ignitable
concentrations of flammable sub-
stances.
Output 1, 3 Switched DC/Open Collector
dc - (open collector)
dc +
common
X_
W_
Y_
Slot A, B
Switched DC
• 30mAdcmaximumsupplycur-
rent
• Shortcircuitlimitedto<50mA
• 22to32VÎ (dc) open circuit volt-
age
• Usedc-anddc+todriveexter-
nal solid-state relay.
• DIN-A-MITEcompatible
• Single-pole:upto4inparallelor
4 in series
• 2-pole:upto2inparallelor2in
series
• 3-pole:upto2inseries
Open Collector
• 100mAmaximumoutputcur-
rent sink
• 30VÎ (dc) maximum supply volt-
age
• Anyswitcheddcoutputcanuse
the common terminal.
• Useanexternalpowersupplyto
control a dc load, with the load
positive to the positive of the
power supply, the load negative
to the open collector and com-
mon to the power supply nega-
tive.
Output 1: (X1,-W1,+Y1)
PM _ _ _ [C] _ - _ _ _ _ _ _ _
Output 3: (X3,-W3,+Y3)
PM _ _ _ _ _ - _ _ [C] _ _ _ _
Switched DC
dc +
dc -
common
X
_
Y
_
W
_
24V
Open Collector
Load
P o wer Supply
dc -
common
X
_
Y
_
W
_
24V
Output 1, 3 Mechanical Relay, Form C
normally open
normally closed
common
L_
K_
J_
Slot A, B
• 5Aat240VÅ (ac) or 30VÎ (dc)
maximum resistive load
• 20mAat24Vminimumload
• 125VApilotdutyat120/240VÅ
(ac), 25 VA at 24VÅ (ac)
• 100,000cyclesatratedload
• Outputdoesnotsupplypower.
• forusewithacordc
See Quencharc note.
Output 1: (L1,K1,J1)
PM _ _ _ [E] _ - _ _ _ _ _ _ _
Output 3: (L3,K3,J3)
PM _ _ _ _ _ - _ _ [E] _ _ _ _
J
normally open
common
normally closed
L
K
_
_
_
Output 1, 3 Universal Process
Universal Process
(Output 1)
volts or current -
current +
volts +
F_
G_
H_
Slot A, B
• 0to20mAinto800Ωmaxi-
mum load
• 0to10VÎ(dc)into1kΩmini-
mum load
• scalable
• outputsuppliespower
• cannotusevoltageandcurrent
outputs at same time
• Outputmaybeusedasre-
transmit or control.
Output 1: (F1,G1,H1)
PM _ _ _ [F] _ - _ _ _ _ _ _ _
Output 3: (F3,G3,H3)
PM _ _ _ _ _ - _ _ [F] _ _ _ _
negative
volts +
current +
F
_
G
_
H
_
4 to 20 mA
0 to 1 0 V
Quencharc Note:
Switching pilot duty inductive
loads (relay coils, solenoids,
etc.) with the mechanical
relay, solid state relay or
open collector output options
requires use of an R.C. sup-
pressor.