Watlow Ez-Zone PM8 - Chapter 5: Operations; Navigating the Operations Page; Operations Page

Watlow EZ-ZONE
®
PM Integrated Controller • 30 • Chapter 5 Operations Page
5
Chapter 5: Operations Page
To go to the Operations Page from the Home Page,
press both the Up ¿ and Down ¯ keys for three sec-
onds. [``Ai] will appear in the upper display and
[oPEr] will appear in the lower display.
• PresstheUp¿ or Down ¯ key to view available
menus. On the following pages top level menus are
identified with a yellow background color.
• PresstheAdvanceKey
‰
to enter and view avail-
able prompts within a menu.
• PresstheUp¿ or Down ¯ key to move through
available menu prompts.
• PresstheInfinityKeyˆ to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
• PressandholdtheInfinityKeyˆ for two seconds
to return to the Home Page.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model number information in the
Appendix for more information. If there is only one instance of a menu, no submenus will appear.
Navigating the Operations Page
[``Ai]
[oPEr] Analog Input Menu
[```1]
[``Ai] Analog Input
[`Ain] Process Value
[`i;Er] Error Status
[`i;Ca] Calibration Offset
[`Lnr]
*
[oPEr] Linearization Menu
[```1]
[`Lnr] Linearization
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[``Pu]
*
[oPEr] Process Value Menu
[```1]
[``Pu] Process Value
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[`dio]
[oPEr] Digital Input/Output Menu
[```5] to [``6]
[`dio] Digital Input/Output
[`do;S] Output State
[`ei;S] Event State
[`di;S] Input State
[Mon]
[oPEr] Monitor Menu
[```1]
[Mon] Monitor
[C;MA] Control Mode Active
[`h;Pr] Heat Power
[`C;Pr] Cool Power
[`C;SP] Closed Loop Working Set
Point
[`Pu;A] Process Value Active
[Loop]
[oPEr] Loop Menu
[```1]
[Loop] Loop
[`r;En] Remote Enable
[`C;M] Control Mode
[A;tSP] Autotune Set Point
[`AUt] Autotune Request
[`C;SP] Closed Loop Set Point
[`id;S] Idle Set Point
[`h;Pb] Heat Proportional Band
[`h;hy] Heat Hysteresis
[`C;Pb] Cool Proportional Band
[`C;hy] Cool Hysteresis
[``ti] Time Integral
[``td] Time Derivative
[``db] Dead Band
[`o;SP] Open Loop Set Point
[ALM]
[oPEr] Alarm Menu
[```1] to [```4]
[ALM] Alarm 1
[`A;Lo] Low Set Point
[`A;hi] High Set Point
P;StA]
[oPEr] Profile Status Menu
[```1] to [```4]
[P;StA] Profile Status
[P;Str] Profile Start
[PACr] Action Request
[`StP] Active Step
[S;tyP] Active Step Type
[t;SP1] Target Set Point Loop 1
[AC;SP] Produced Set Point 1
[`St;i] Step Type Remaining
[Ent1] Active Event Output 1
[Ent2] Active Event Output 2
[``JC] Jump Count Remaining
Operations Page
* Available with PM4, PM8 and PM9 models only