SAFETY INSTRUCTIONS
Read and understand the owner’s manual and labels affixed to the machine. Learn its application and
limitations as well as the specific potential hazards. Retain these instructions for future reference. The
operator is responsible for following the warnings & instructions in this manual and on the product.
Read & understand operator’s manual
before using the machine. Failure to
follow instructions could result in death
or serious injury.
Please keep in a safe place for future
reference.
Whenever the machine is in use,
safety glasses/goggles must be worn
to safeguard against flying objects.
Hearing protection must also be
used to protect the operators
hearing. If the operator is working in
an area where there is a risk of
falling objects, a safety helmet must
also be worn.
DANGER
Keep all bystanders & animals at least
15 metres away from the machine
during operation.
If approached, stop the machine
immediately.
Wear protective gloves to protect
your hands.
Wear protective footwear
Double insulated or class 2 electrical
appliances are products that have been
designed in a way so as not to require a
safety connection to electrical earth
(These products must NOT have a
safety connection to Earth).
DANGER — THROWN DEBRIS
Remove objects that can be thrown
by the machine in any direction.
Wear safety glasses.
Noise Level - See label on machine
Before making adjustments,
changing parts, cleaning, or working
on the log splitter, always disconnect
the power. Consult the technical
manual before servicing.
Keep guards in place and in working
order. Replace damaged, missing or
failed parts before using it.
Do not expose to rain or damp
conditions.
Do not use near a flame, or sparks
The chainsaw is supplied with a
KICKBACK chain, however sometimes
kick back can occur, so always hold the
unit firmly in two hands. The Kickback
danger zone on your chainsaw is the
upper part of the nose of the guide bar.
Never saw with the danger zone, which
poses a significant risk for kickback.
Correct direction of cutting teeth
Safety alert symbol. Used to alert you
to potential personal injury hazards.
Obey all safety messages that follow
this symbol to avoid possible injury.
Indicates an imminently hazardous
situation which, if not avoided, will
result in serious injury
Indicates a potentially hazardous
situation which, if not avoided, could
result in serious injury
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury.
Used without the safety alert symbol
indicates a potentially hazardous
situation which, if not avoided, may
result in property damage.
CE Marking - the product meets
demand and regulations set by the
EU
RISIDUAL RISKS
Even with the intended use of the appliance there is always a residual risk, which cannot be prevented.
According to the type and construction of the appliance the following potential hazards might apply:
- Contact with exposed saw teeth of the saw chain (cutting hazards)
- Access to the rotating saw chain (cutting hazards)
- Unforeseen, abrupt movement of the guide bar (cutting hazards)
- Flung out of parts from the saw chain (Cutting / injection hazards)
- Flung out of parts of the work piece
- Inhalation of wood particles,
- Skin contact with chain oil,
- Loss of hearing, if required ear protection not used during work.
ELECTRICAL REQUIREMENTS
Connect the main leads to a standard 220-240V±10% (50Hz±1Hz) electrical supply which has protection
devices of under-voltage, over-voltage, over-current as well as a residual current device (RCD) which maximum
residual current rated at 0.03A.
EXTENSIONS LEADS
Improper use of extension cords may cause inefficient operation of the machine which can result in
overheating. Be sure the extension cord is no longer than 10m and its section is no less than 2.5mm² to allow
sufficient current flow to the motor. Avoid use of free and inadequately insulated connections. Connections
must be made with protected material suitable for outdoor use.
INSPECT YOUR LOG
Make sure there are no nails or foreign objects in logs to be split.
WARNING
Please note that our equipment has not been designed for use in commercial, trade or industrial
applications. Our warranty will be 90 days from the original date of sale for commercial, trade or industrial
businesses or for equivalent purposes.
To Next Page
Loading...