To Next PageTo Next PageWhat to do if Well Power Supply shows overload symbol and beeps?
If your Well Power Supply displays the overload symbol or the overload LED is on and beeping, it means the UPS is overloaded. Remove non-critical loads to resolve this issue.
What to do if Well Power Supply shows error symbol?
If the error symbol appears or the overload LED is lit (not due to overload) and the Well Power Supply beeps, the issue could be due to several reasons: * The UPS is overheating: Remove non-critical loads. * The ventilation slots are blocked: Clean the ventilation slots. * The ambient temperature is too high: Disconnect the output and input, wait 30 minutes, then restart. * The consumer is short-circuited: Remove the consumer, restart the UPS. * The fan is defective: Replace it.
Why Well Power Supply goes to battery mode when there is power?
The Well Power Supply switches to battery mode even when there is mains power because the input voltage or frequency is outside the acceptable range. Wait for the input voltage or frequency to return to normal.
What to do if Well Power Supply has short backup time?
If your Well Power Supply has a short backup time, it could be due to: * Insufficient charging time: Charge the battery for at least 10 hours. * A faulty battery: Replace the battery.
How to fix Well Power Supply that won't turn on with mains power?
If your Well Power Supply doesn't turn on even when mains power is available, the power button may not have been pressed long enough. Press and hold the main switch until the UPS beeps.
How to fix Well UPS-HEATST-STEADY500VA-WL that won't turn on in battery mode?
If your Well Power Supply doesn't turn on in battery mode, try the following: * Ensure you press and hold the main switch until the UPS beeps. * Charge the battery, as it may be empty. * Check and tighten or connect the battery connection if it's loose or disconnected.
What to do if Well UPS-HEATST-STEADY500VA-WL Power Supply battery won't charge?
If the Well Power Supply battery won't charge, the battery may be defective and needs replacement.
General| Brand | Well |
|---|---|
| Model | UPS-HEATST-STEADY500VA-WL |
| Category | Power Supply |
| Language | English |
Ensures correct earth cable selection and connection for user and unit safety, warning about improper diameter.
Stresses that only authorized technical service personnel should repair the UPS to prevent dangerous situations.
Warns that placing magnetic storage media on top of the UPS may lead to data corruption.
Provides special precautions for UPS input from a generator, regarding output capacity and frequency.
Lists the items included in the package: UPS, User's Manual, Warranty Card, and Battery Cable.
Instructs users to ensure the UPS is not damaged and to contact the seller if any damage is found.
Provides instructions for placing the UPS in a cool, dry, clean, and well-ventilated area, away from heat and vibration.
Specifies recommended operating temperature (-10°C to +40°C), humidity (10%-90%), and altitude (<1000m).
Identifies components like power switch, LCD display, and LED indicators on the front panel of UPS models.
Details rear panel components including charging selector, battery terminals, AC input, output sockets, and USB port.
Specifies battery cable requirements based on UPS model, ensuring adequate over current ability.
Details connecting the battery, including voltage check, disconnection from mains, and correct polarity.
Recommends a minimum 20AH battery for long backup, warning about potential damage to smaller batteries.
Provides instructions for plugging the UPS into the wall socket and connecting appliances to the UPS.
Press the power switch to turn on the UPS and then switch on connected appliances one by one.
Turn off appliances, then press the power switch. Note: UPS may still charge the battery after output is off.
Recommends selecting charging current based on battery capacity to prevent damage. Warning included.
Use the temporary mute button to mute alarms. Mute function may reset upon power restore and failure.
Details the USB port for charging mobile phones or powering small USB devices, noting the output limit.
Explains that the UPS can function as an AVR even without a battery connected, providing regulated output.
Recommends charging the battery every three months and discharging if in mains mode for over four months.
Discusses factors affecting battery life, such as usage, discharge cycles, and temperature, emphasizing regular checks.
The UPS will emit a beep every 30 seconds when operating in battery mode.
Alerts to low battery levels with periodic beeps, escalating to rapid beeps and auto-shutdown when near empty.
Details how the UPS responds to overheating, including rapid beeping and automatic output cutoff or shutdown.
Explains overload alerts, with beeps every second in mains mode and rapid beeps leading to shutdown in battery mode.
Describes short circuit handling: circuit breaker trip in mains mode and rapid beeps with shutdown in battery mode.
Details protection against incorrect battery polarity, which burns an internal fuse to prevent inverter damage.
Instructs to disconnect UPS and clean the body and ventilation holes using a cotton cloth and detergent.
Advises checking parameters for malfunctions, performing inspection during thunderstorms, and not during operation.
