Wisper Cool RW3000 - Installation Guide; Electrical Wiring and Power Supply; Mounting Window Models; Chain Kit Installation

INTRODUCTION
Evaporativecoolingworksontheprincipleofheatabsorptionbymoistureevaporation.
Whenaswimmerleavesthewateronawindyday,hefeelscoolbecausethemoisture
on his bodyis evaponiing and absorbing heat.
Yourevaporativecoolerdraws exteriorairinto specialpadssoakedwithwater,where
the airis cooledbyevaporation,then circulatedintoyourhome.
Your evaporativecoolermakesthebestpossibleuseof the evaporativeprocessby
meteringthe flowofwater,distributingit evenlythroughthefiltermedia,andblowing
a steadystreamofcooledairintoyourhome.Theairisthen channeledthroughthe
buildingandventedoutofthehomethroughopenwindows,doorsorvents.
INSTALL.ATION
MountingOfYourModelRW3000EvaporativeCooler
l_n!portant: Read these instructions
carefully before installing,
operating or servicing your
evaporative cooler.
SAFETY
Unplug
the electrical cord
to the cooler before
attempting to work
on or service your
cooler.
•1. Checklocalcodesand uiilitystandards The
inadlaion mustcomptywith theirrides.
2. Yourcoolerwillmn on 120voltAC,60Hz
(c_l,)currento_
3. Vseagronndedoutlet tol_oua yonfrom
shock,lf theoutletyouplan touse isa 2-prong
@pe,do not remove the plug grounding
prong. Havean electricianreplacethe2-prong
outlet with a grounded 3-prong outlet.
Location
Installcoolersoonlyfreshoutsideairispermitted
toenterthecnnlingsystem,preferablyonsideof
buildingfacingprevailingwinds.Installunitthrough
windowofroomwheremaximumcoolingisdesired.
Airflowcanbedkectedthroughhousobyusing
otherwindowsasexhaustopenings.Avoidinstalling
unitinsidedosedinareas,suchas anatticor
storageroomwhichrestrictsfreeairmovement
aroundconler._o'nlinstallationnearve.mpipes,
ldtcbenexhaust,etc.,as odorsorfumesmaybe
drawaintounits.
ElectricalWiring
Yourunithasbeenpre-wh'edatthefantoryso
fiat.herwiringis notnecessary.Figure1showsthe
wiringdiagramd youruintincaseofelectricnl
componentreplacement.
_Jm MOTOR
Power Supply
Besuremconnectto120volts,60Hzgrounded
powersoppl_Note:Impropervoltagewillbum
outmotorandpumpwindingsandvoidthe
warranty.
Mounting Window Models
Assurettmthemonntingsurhce isstrong
enoughtobeartheweightofthecoolerwhen
inuse.Rememberthatwhenthesystemfills
withwater,thecoolerwillbemuchheavier
thanwhead_.Theaoa commonmethodof
installationinvolvesmoun_ngthecoolerona
flatsupporter standprovidedbytheinstaller.
Tbedoctendgrilleportinnareplacedthrough
nGla_ 2
mlH
thewindow
openingand
wmdowp_s
arefittodinto
po_nn (see
Figure2).
Mothermethod
ofinstallation
involvestheuse
ofa chainIdt
andstandoff
hardware.
To Install Cooler
Using A Chain Kit
1.Attachscrewhooksto outsidewindowflame
approximatelytwofeetabovecooler.Besure
hunkis insertedtofnlldepthInframefor
_um strength.Attachchaintoeachhunk
2, ffyour cooler does not haveholes
predrilled, drill3/16"holes1"aboveeachpad
kame comeratrearofcoolercabinet.Bolt