17
POWER VENT KIT FOR L200H
/ L200M / DH4000
1 OF 1
REV
CUSTOMER
DWG FILE NAME
CHECKED
TITLE
AS
SHEETSCALE
DRAWN BY
NTS
12 Stevens Road
Brewer, Maine 04412
Tel: 1-207-989-4335 Int'l: 1-800-777-6953
Fax: 1-207-989-1101 Email: info@nyle.com
1.0
17
3
L1
L2
MAIN TERMINAL
STRIP IN KD250
CONTROL BOX
EXHAUST FAN MOTOR
(220V)
WIRING DIAGRAM FOR
POWER VENT KIT 240V
L200H / L200M / DH4000
240V
Power Vent Wiring
Fan Diagram
REFERENCE
FAN DIAGRAM
1 OF 1
REV
CUSTOMER
DWG FILE NAME
CHECKED
TITLE
PB
DWG FILE NAME
SHEETSCALE
DRAWN BY
NTS
12 Stevens Road
Brewer, Maine 04412
Tel: 1-207-989-4335 Int'l: 1-800-777-6953
Fax: 1-207-989-1101 Email: info@nyle.com
1.0
1/3 HP MOTOR
CARRIAGE
BOLT
SPACER
NUT
FAN HOUSING
PROPELLOR
HUB
NOTE: HUB FACES
AWAY FROM MOTOR
1. MOUNT MOTOR ON BASE USING SPACERS, BOLTS AND NUTS PROVIDED
2.PLACE FAN ON MOTOR SHAFT SO THAT ONE SCREW SET MEETS THE FLAT OF THE
SHAFT. TIGHTEN BOTH SET SCREWS
3.ADJUST THE MOTOR SO THAT THE TIO OF THE BLADE IS EVENLY SPACED AND AT
THE TRHOAT OF THE VENTURI
4.FAN MOTOR CAN BE WIRED FOR 240V OR 120V BUT THE SWITCH SUPPLIED IS 240
VOLTS ONLY. IT HAS A BUILT IN OVERLOAD.
AIR
WIRING SUGGESTION : CHECK ON LOCAL CODES
REFERENCE
FAN DIAGRAM
1 OF 1
REV
CUSTOMER
DWG FILE NAME
CHECKED
TITLE
PB
DWG FILE NAME
SHEETSCALE
DRAWN BY
NTS
12 Stevens Road
Brewer, Maine 04412
Tel: 1-207-989-4335 Int'l: 1-800-777-6953
Fax: 1-207-989-1101 Email: info@nyle.com
1.0
1/3 HP MOTOR
CARRIAGE
BOLT
SPACER
NUT
FAN HOUSING
PROPELLOR
HUB
NOTE: HUB FACES
AWAY FROM MOTOR
1. MOUNT MOTOR ON BASE USING SPACERS, BOLTS AND NUTS PROVIDED
2.PLACE FAN ON MOTOR SHAFT SO THAT ONE SCREW SET MEETS THE FLAT OF THE
SHAFT. TIGHTEN BOTH SET SCREWS
3.ADJUST THE MOTOR SO THAT THE TIO OF THE BLADE IS EVENLY SPACED AND AT
THE TRHOAT OF THE VENTURI
4.FAN MOTOR CAN BE WIRED FOR 240V OR 120V BUT THE SWITCH SUPPLIED IS 240
VOLTS ONLY. IT HAS A BUILT IN OVERLOAD.
REFERENCE
FAN DIAGRAM
1 OF 1
REV
CUSTOMER
DWG FILE NAME
CHECKED
TITLE
PB
DWG FILE NAME
SHEETSCALE
DRAWN BY
NTS
12 Stevens Road
Brewer, Maine 04412
Tel: 1-207-989-4335 Int'l: 1-800-777-6953
Fax: 1-207-989-1101 Email: info@nyle.com
1.0
1/3 HP MOTOR
CARRIAGE
BOLT
SPACER
NUT
FAN HOUSING
PROPELLOR
HUB
NOTE: HUB FACES
AWAY FROM MOTOR
1. MOUNT MOTOR ON BASE USING SPACERS, BOLTS AND NUTS PROVIDED
2.PLACE FAN ON MOTOR SHAFT SO THAT ONE SCREW SET MEETS THE FLAT OF THE
SHAFT. TIGHTEN BOTH SET SCREWS
3.ADJUST THE MOTOR SO THAT THE TIO OF THE BLADE IS EVENLY SPACED AND AT
THE TRHOAT OF THE VENTURI
4.FAN MOTOR CAN BE WIRED FOR 240V OR 120V BUT THE SWITCH SUPPLIED IS 240
VOLTS ONLY. IT HAS A BUILT IN OVERLOAD.
AIR
To Next Page
Loading...