To Next Page
J
Jessica LittleAug 1, 2025
How to fix forward infeed coil fault in Woods 8000?
- PpjonesAug 1, 2025
If a forward infeed coil fault occurs on the Woods Chipper, test the wiring to the forward coil. If the coil is out of specification, replace it.
How to fix forward infeed coil fault in Woods 8000?
If a forward infeed coil fault occurs on the Woods Chipper, test the wiring to the forward coil. If the coil is out of specification, replace it.
How to troubleshoot reverse coil fault in Woods Chipper?
If a reverse coil fault occurs on the Woods Chipper, test the wiring to the reverse coil. Replace the coil if it is out of specification.
How to reset blade service code on Woods 8000 Chipper?
If the blade service code is active on your Woods Chipper, and the control system hasn't detected chipper RPM after placing the feed bar in NEUTRAL after power up, service the blades. To reset the code, turn the key on and shift the feed bar from REVERSE to REVERSE then back 3 times within 60 seconds of turning the key on. Note that the engine cannot be running during this process.
What to do if Woods Chipper has been below operational RPM for more than 10 minutes?
If the Woods Chipper has been below operational RPM for more than 10 minutes, the 10-minute timer safety feature will activate. To resume operation, return the safety bar to the NEUTRAL position.
What to do if safety bar was activated on Woods 8000?
If the safety bar on the Woods Chipper was activated and forward coil or reverse coil faults are not active, push the Safety Bar Reset/Override Switch.
What if feed bar not in NEUTRAL on Woods 8000 startup?
If the feed bar is not in NEUTRAL upon initial startup of the Woods Chipper, place the feed bar in NEUTRAL.
Essential safety instructions and adherence to all manual guidelines.
Pre-operation checks and securing the equipment for safe use.
Safe operating procedures and precautions during use.
Safety measures for moving the chipper between locations.
Safety guidelines for performing maintenance and servicing.
Proper procedures for safely storing the chipper when not in use.
Visual identification and understanding of critical safety decals on the unit.
Detailed explanation of the chipper's components, controls, and their functions.
Key steps and checks required before starting the chipper.
Step-by-step guide for securely mounting the chipper to a tractor.
Ensuring proper tractor stability during operation and transport.
Safe procedures for starting the tractor and engaging the chipper.
Safe methods for shutting down the chipper and tractor.
Best practices for efficient and safe chipper operation.
Function and operation of the feed roller control bar for material feeding.
Understanding the chipper's controller and its operational feedback.
Adjusting feed roller speed for optimal material processing.
Guidelines for proper and safe storage of the chipper.
Procedures for cleaning the chipper after use to maintain performance.
Schedule and points for lubricating the chipper's moving parts.
Procedure for using the disk lock to secure the disc during maintenance.
Essential maintenance for chipper blades to ensure performance.
Detailed instructions on how to sharpen chipper blades for optimal cutting.
Correctly setting the clearance between the chipper anvil and blades.
Step-by-step guide for replacing worn or damaged chipper blades.
Lubrication requirements for the PTO driveline assembly.
Safe methods to clear obstructions from a plugged chipper rotor.
Guidance on adjusting belt tension or replacing worn drive belts.
Procedures for removing and installing new bearings.
Steps for replacing the hydraulic oil filter for system maintenance.
Instructions for filling the hydraulic system and purging air.
Interpretation of controller indicator light codes for diagnostics.
A table listing common issues, causes, and solutions for the chipper.
Diagram illustrating the chipper's hydraulic system layout.
Diagram showing the chipper's electrical wiring and components.
Guidelines for dealers to properly assemble and prepare the chipper.
Instructions for assembling the discharge tube to the chipper.
Steps to shorten the driveline for proper tractor PTO connection.
Wiring guide for the control box on the Model 8100 chipper.
Dealer checklist for ensuring correct setup before customer delivery.
Dealer checklist for customer orientation and final delivery checks.
Glossary of abbreviations used throughout the manual.
General